Surface tension is a physical property of a fluid interface that causes it to resist an increase in area. It can be expressed as a tangential force per unit length or, equivalently, as the reversible work required to create a unit of interfacial area under specified conditions. The term commonly refers to a liquid–gas boundary; interfacial tension is the broader term, often used for the boundary between two immiscible liquids. Surface tension explains why small droplets are nearly spherical, why liquid rises or falls in narrow tubes, and why some objects denser than a liquid can remain supported at its surface.
Physical origin
Surface tension arises because the molecular environment at an interface differs from that within either bulk phase. In a liquid, a molecule interacts with surrounding molecules through forces that may include van der Waals forces, electrostatic interactions, and hydrogen bonding. Near an interface, molecular surroundings, organization, and fluctuations change. Creating additional interface generally requires an increase in free energy.
A common introductory picture describes surface molecules as having fewer attractive neighbours than molecules in the interior. This gives useful intuition, but surface tension is not simply an uncompensated inward pull on every surface molecule. A complete account involves the interfacial distribution of molecular forces and the contributions of both energy and entropy.
In a mechanical description, the pressure tensor within an interface is generally anisotropic: normal and tangential stresses differ. For a planar interface, the surface tension can be written as
where is surface tension, is distance normal to the interface, and and are the normal and mean tangential components of the pressure tensor.
The analogy between a liquid surface and a stretched elastic membrane has limits. An ordinary clean liquid interface does not possess the persistent in-plane shear rigidity of a solid sheet. Its molecules continually rearrange, and its tension need not increase when its area is increased.
Definition, units, and thermodynamics
For a straight segment of length bounding a single uniform interface, the magnitude of the force exerted perpendicular to the segment and tangent to the interface is
A soap film normally has two liquid–gas interfaces. Consequently, an ideal film pulling on a movable wire of length exerts approximately , provided both interfaces have the same tension and edge effects are negligible.
The SI unit of surface tension is the newton per metre:
The equivalence of these units connects the mechanical and energetic descriptions.
Within thermodynamics, creating interfacial area introduces a term into the differential of the appropriate free energy. For an equilibrium system with one independently variable interfacial area, a common expression is
where is Gibbs free energy, is area, and temperature, pressure, and component amounts are held fixed. Under fixed-temperature, fixed-volume conditions, the corresponding derivative uses Helmholtz free energy.
These expressions require a consistent description of the interface and its constraints. For mixtures, redistribution of material between the bulk and the interface must also be considered. Surface tension is a free-energy cost, not generally the interfacial internal energy per unit area.
Curvature and the Young–Laplace equation
A curved interface with uniform surface tension supports a difference in pressure between its two sides. The Young–Laplace equation expresses this balance:
where and are the principal radii of curvature, with signs determined by the chosen interface normal.
For a spherical liquid droplet of radius , surrounded by gas,
Thus, smaller droplets have larger excess internal pressures. For a thin spherical soap bubble, two interfaces contribute, giving approximately
when the film thickness is negligible compared with its radius.
Positive surface tension favours a reduction in interfacial area, subject to volume and other constraints. A sphere has the least surface area for a given enclosed volume, so sufficiently small, freely suspended droplets tend to be spherical. Larger droplets are more strongly distorted by gravity, contact with solids, or fluid motion.
Surface tension also drives the breakup of sufficiently long liquid jets into droplets. Such breakup can reduce total surface area, although inertia and viscosity affect how the instability develops.
Wetting and capillary action
Contact angle
Wetting describes how a liquid spreads on or adheres to a solid. It depends on the balance among solid–gas, solid–liquid, and liquid–gas interfacial properties, rather than on liquid surface tension alone.
For an ideal smooth, rigid, chemically homogeneous surface at equilibrium, Young’s equation is
where is the contact angle measured through the liquid and the subscripts identify the adjoining phases.
A small contact angle indicates stronger wetting; a large angle indicates weaker wetting. Real surfaces commonly show contact-angle hysteresis: an advancing liquid edge and a receding edge have different apparent contact angles because roughness or chemical heterogeneity pins the contact line. Consequently, a measured angle is not always a unique equilibrium material property.
Capillary rise and depression
Capillary action results from surface tension acting together with wetting and pressure differences across curved liquid surfaces. In a narrow circular tube, a wetting liquid generally forms a concave meniscus and rises above the surrounding reservoir. A non-wetting liquid can form a convex meniscus and be depressed.
For an ideal vertical tube of radius , equilibrium height is approximately
where is the density difference between liquid and surrounding fluid, and is gravitational acceleration. The expression assumes a uniform tube and neglects corrections associated with the detailed meniscus geometry.
Capillarity is important in porous materials, paper, textiles, soils, and groundwater systems. In these settings, pore geometry and interconnected flow paths make the behaviour more complex than that of a single tube.
Competition with gravity
The capillary length measures the scale at which surface tension and gravity have comparable effects:
For a clean water–air interface near room temperature, it is about millimetres. Surface tension usually dominates static shape at lengths much smaller than this, while gravity becomes increasingly important at larger scales.
Small insects and some carefully placed dense objects can be supported by a liquid surface through the combined effects of buoyancy and vertical components of surface-tension forces. The surface is not an impermeable solid skin.
Temperature, composition, and surfactants
Temperature dependence
For most ordinary pure liquids, surface tension decreases as temperature increases. Along liquid–vapour coexistence, it approaches zero at the critical point, where the distinction between liquid and vapour disappears.
Clean water in contact with air has a surface tension of approximately at . Under comparable conditions, ethanol has a much lower value, around . Values depend on temperature, composition, and the phase contacting the liquid.
Surface-active substances
A surfactant is a substance that preferentially accumulates at an interface and changes its properties, usually lowering surface or interfacial tension. Many surfactants contain a water-compatible region and a region with low affinity for water. Their adsorption can substantially change tension even when their bulk concentration is small.
At fixed temperature, the Gibbs adsorption equation relates changes in interfacial tension to changes in component chemical potentials:
where is the surface excess amount of component per unit area, defined relative to a chosen dividing surface.
Surfactant accumulation often lowers tension as concentration increases. Above the critical micelle concentration, added surfactant predominantly enters molecular aggregates, and surface tension commonly changes much more slowly. Not all dissolved substances reduce tension: many inorganic salts increase the surface tension of water over relevant concentration ranges.
Dynamic surface tension
A newly created interface need not immediately reach its equilibrium composition. Surfactant transport by diffusion, adsorption, desorption, and interfacial rearrangement takes time. Dynamic surface tension therefore depends on the age and deformation history of an interface.
This distinction matters in processes that rapidly create fresh area, including spraying, printing, foaming, and droplet formation. An equilibrium value alone may not describe their behaviour.
Surface-tension gradients and fluid motion
Spatial variations in temperature or composition can produce surface-tension gradients. These gradients exert tangential stresses and generate the Marangoni effect. At the interface, the resulting stress tends to draw fluid toward regions of higher surface tension.
Examples include flows in evaporating liquid films, motion caused by locally added surfactant, and thermally driven circulation during materials processing. The full flow pattern also depends on geometry, viscosity, heat transfer, and material transport.
Surfactants can help stabilize foams and emulsions, but lowering tension is not the only mechanism involved. Resistance to film thinning, interfacial rheology, and forces between closely spaced interfaces can be equally important.
Measurement
Common techniques determine surface tension from forces, pressures, or interface shapes:
- Wilhelmy plate: measures the wetting force on a thin plate with known wetted perimeter. Reliable interpretation requires control of the contact angle and a correction for buoyancy.
- Du Noüy ring: measures the force associated with pulling a ring through an interface. Corrections account for the shape and weight of the lifted liquid.
- Pendant-drop and sessile-drop analysis: infer tension by fitting a droplet profile to the balance between gravity and capillary pressure.
- Capillary-rise measurement: uses the rise or depression in a tube of known radius, together with the contact angle and density difference.
- Maximum bubble-pressure measurement: uses the pressure needed to grow bubbles through a submerged capillary and can probe dynamic surface tension.
Contamination is a major source of error, especially for water and dilute surfactant solutions. Temperature control, clean apparatus, accurate density values, instrument calibration, and the elapsed time after interface formation all affect results. Reported measurement uncertainty should reflect both instrumental limitations and the suitability of the physical model used.
Applications and limitations
Surface tension is central to coating, printing, detergency, soldering, emulsification, foam production, spray formation, and microfluidic droplet control. In small devices, interfacial forces can dominate forces that are more important at everyday scales.
Its role in moving fluids is often assessed through dimensionless ratios. The capillary number,
compares viscous stresses with surface-tension stresses, where is dynamic viscosity and is a characteristic speed. The Weber number,
compares inertial and surface-tension effects. Their significance depends on the flow geometry and other relevant parameters; neither gives a universal threshold for droplet breakup.
Biological interfaces are often more complex than clean liquid surfaces. Pulmonary surfactant reduces surface tension at the lung’s air–liquid interfaces, while the mechanical behaviour of a cell membrane also involves lipid organization, membrane bending, and coupling to other cellular structures.
At molecular length scales, a sharp interface with a single constant tension may be inadequate. Strong curvature, molecular layering, thermal fluctuations, and interactions between nearby interfaces can require more detailed descriptions. For solids, surface stress and surface free energy per unit area are also generally distinct, so liquid-interface formulas cannot be transferred unchanged.
Historical development
Early studies of narrow tubes, menisci, and liquid cohesion preceded the modern concept of surface tension. In the early nineteenth century, Thomas Young developed a force-based account connecting capillarity with contact angles, while Pierre-Simon Laplace developed a mathematical relation between interface curvature and pressure difference.
Later work by James Clerk Maxwell and Josiah Willard Gibbs helped place interfacial phenomena within mechanical and thermodynamic frameworks. Twentieth-century developments in molecular theory, surfactant chemistry, and experimental measurement extended the subject to films, emulsions, dynamic interfaces, and molecular-scale descriptions.