A synchronous motor is an alternating-current electric motor whose rotor, during steady operation, turns at the same speed as the rotating magnetic field produced by its stator. Its speed is determined by the electrical supply frequency and the number of magnetic poles, rather than by the amount of mechanical load. Unlike an induction motor, it does not require a sustained difference between rotor speed and magnetic-field speed to produce torque.
Synchronous motors range from small timing and positioning devices to industrial machines rated at many megawatts. Their rotor excitation may come from direct-current windings, permanent magnets, or a magnetic structure that produces reluctance torque without separate excitation. Directly connected machines provide constant-speed mechanical power and, in some designs, adjustable reactive-power exchange. With electronic control, synchronous motors also provide efficient variable-speed operation in industrial drives, household equipment, robotics, and electric vehicles.
Rotating fields and synchronous speed
A balanced three-phase supply applied to appropriately distributed stator windings produces a magnetic field whose fundamental component rotates around the air gap at constant angular velocity. The currents in the three phases are displaced by 120 electrical degrees, and the winding axes have corresponding spatial displacements. Their combined magnetomotive force forms a rotating wave rather than three independently pulsating fields. Practical winding arrangements approximate this ideal field while also producing smaller spatial harmonics.
The speed of the fundamental rotating field is
where is the synchronous speed in revolutions per minute, is the electrical frequency in hertz, and is the total number of poles. A four-pole motor supplied at 50 Hz therefore runs synchronously at 1,500 revolutions per minute; at 60 Hz it runs at 1,800 revolutions per minute. A twelve-pole motor at 50 Hz runs at 500 revolutions per minute. Increasing pole count permits lower shaft speed without a mechanical gearbox.
If is the number of pole pairs, the relationship between electrical angular frequency and mechanical angular speed is
This distinction is important in electronic control: one mechanical revolution of an eight-pole motor corresponds to four electrical cycles. Rotor-position measurements must therefore be converted into electrical angle before they can be used to coordinate stator currents.
Torque arises because the rotor’s magnetic structure tends to align with the rotating stator field. In an excited rotor, the interaction involves a rotor magnetic field produced by windings or permanent magnets. In a reluctance rotor, torque results from the tendency of the magnetic circuit to adopt an orientation of lower reluctance. In either case, steady torque is possible while rotor speed exactly matches the fundamental rotating-field speed.
Synchronism does not imply that the rotor and stator magnetic axes coincide. A loaded motor operates with a finite angular displacement between them. When load increases, the rotor briefly slows relative to the rotating field, increasing this displacement until a new torque balance is reached. Its steady speed then returns to synchronous speed. This load-dependent angular displacement distinguishes synchronization from a rigid mechanical connection.
For an induction motor, slip is commonly defined as . A synchronous motor has zero steady-state slip relative to the fundamental field. However, it can still experience transient speed deviations, torsional oscillations, and losses associated with harmonic fields. The term “synchronous” describes its fundamental operating relationship, not an absence of all relative electromagnetic motion.
Construction and principal motor types
The stator normally consists of a laminated magnetic core carrying insulated alternating-current windings. Thin sheets of electrical steel reduce eddy-current losses while providing a low-reluctance path for magnetic flux. Slots accommodate the conductors, and the winding arrangement establishes pole count and influences harmonic content. The frame, shaft, bearings, cooling system, and insulation structure must withstand electromagnetic forces, mechanical loading, temperature rise, and the intended operating environment.
In a wound-field synchronous motor, direct current flowing through rotor windings establishes the excitation field. Salient-pole rotors have projecting poles and are common where relatively low speed and many poles are required. Cylindrical or nonsalient rotors have a more nearly uniform air gap and are suitable for higher rotational speeds. Rotor geometry is constrained by centrifugal stress as well as electromagnetic requirements; projecting poles and their attachments become more difficult to retain as speed increases.
Excitation can reach the rotor through slip rings and brushes, or through a brushless exciter. A typical brushless arrangement places an alternating-current exciter armature and rotating rectifier assembly on the shaft. The rectifiers supply direct current to the main rotor winding without a sliding electrical connection. This reduces brush maintenance, although rotating diodes and excitation components introduce their own inspection and protection requirements. Many line-start machines also incorporate conducting damper bars in the rotor pole faces.
A permanent-magnet synchronous motor replaces the field winding with magnets. Surface-mounted designs place magnets near the rotor circumference, often beneath a retaining sleeve. Interior designs embed magnets within the rotor, providing mechanical retention and allowing magnetic saliency to contribute additional torque. Magnet material, temperature capability, corrosion protection, and demagnetization resistance affect the usable operating range. Ferrite magnets and rare-earth magnets offer different combinations of cost, magnetic strength, and temperature characteristics.
A synchronous reluctance motor uses a rotor whose magnetic reluctance differs strongly with direction. Flux barriers and iron paths create a preferred magnetic axis, allowing torque production without rotor excitation windings or permanent magnets. Magnet-assisted reluctance designs combine this anisotropic structure with magnets. The distinctions between motor families are therefore not absolute: a single machine can produce both magnet torque and reluctance torque.
Hysteresis motors form another, generally smaller, class. Their rotors use magnetic material with appreciable hysteresis, enabling starting torque and eventual synchronous operation. Separately, brushless DC motors are closely related to permanent-magnet synchronous motors. The terminology usually distinguishes trapezoidal back electromotive force and block commutation from sinusoidal excitation, rather than identifying completely unrelated electromagnetic principles.
Equivalent circuits, torque, and reactive power
For a balanced wound-field machine in sinusoidal steady operation, a useful simplified per-phase model contains an internal generated voltage , stator resistance , and synchronous reactance . With current defined as entering the motor, the terminal-voltage relationship is
The quantities are complex phasors expressed on a consistent per-phase basis. Synchronous reactance represents both leakage effects and the fundamental influence of stator current on the magnetic field. This model is useful for explaining operation, although saturation, saliency, and transient behavior require more detailed representations.
For a cylindrical-rotor motor with negligible stator resistance, the approximate three-phase electromagnetic power is
where and are root-mean-square phase-voltage magnitudes and is the electrical angle by which the internal voltage lags the terminal voltage during motoring. Electromagnetic torque is . Mechanical output is smaller than electromagnetic power because bearings, ventilation, and other rotational effects consume power.
The equation explains how torque can rise without changing steady speed: the load angle increases. In this idealized model, maximum electromagnetic power occurs at 90 electrical degrees. Actual operating limits cannot be inferred from that value alone. Resistance, magnetic saturation, saliency, excitation limits, supply conditions, and transient stability all affect the permissible operating region. A salient-pole machine also develops reluctance torque because its direct-axis and quadrature-axis reactances differ, adding a term proportional to .
Rotor excitation also affects reactive power. At approximately constant shaft load and terminal voltage, changing field current changes the phase and magnitude of stator current. A lightly excited wound-field motor generally draws lagging current and absorbs reactive power; sufficient overexcitation produces leading current and supplies reactive power. Between these conditions, a minimum stator-current region occurs near unity power factor. Plots of armature-current magnitude against field current at constant load are traditionally called V-curves.
This adjustable reactive-power behavior distinguishes wound-field machines from ordinary induction motors and from permanent-magnet machines whose rotor excitation cannot be directly varied. Nevertheless, excitation cannot be increased without limit. Stator current, rotor winding temperature, magnetic saturation, and stability constrain operation.
A synchronous machine running with little or no useful shaft load can be operated as a synchronous condenser for voltage and reactive-power support. Its real-power input covers losses, while its excitation controls reactive exchange. In an inverter-fed motor, by contrast, grid-side power factor depends substantially on the converter’s input stage and controls, not simply on the motor’s internal excitation.
Starting, synchronization, and dynamic stability
A conventional synchronous motor supplied directly at fixed frequency is generally not inherently self-starting through synchronous torque alone. At standstill, the stator field passes the rotor rapidly. The torque acting on a stationary excited rotor changes direction too quickly to provide reliable average acceleration. Permanent magnets do not by themselves eliminate this difficulty: a rotor must be brought into a suitable speed and angular relationship with the rotating field.
One traditional solution is induction starting. Conducting damper bars connected at their ends form a cage-like circuit in the rotor. While the rotor turns below synchronous speed, induced currents in this cage produce induction-motor torque. In a wound-field machine, the main field circuit is handled through a starting arrangement that limits induced voltage; a discharge resistor may be connected across it. Near synchronous speed, direct-current excitation is applied with appropriate timing, allowing the rotor to pull into step.
Successful pull-in depends on more than reaching a particular speed. Load torque, combined motor-and-load inertia, terminal voltage, field strength, and the rotor’s angular position all influence whether synchronization occurs. A high-inertia load can require substantial acceleration time and impose severe heating on starting components. Some installations use a separate starting motor or another mechanical arrangement to bring the synchronous machine near operating speed before synchronization.
A variable-frequency drive offers a different approach. It begins with a low stator frequency and increases frequency while controlling current and rotor angle. The rotating field therefore does not immediately outrun the rotor. The attainable acceleration is limited by available torque, current, voltage, and mechanical inertia, rather than by the need to synchronize with an already fast-moving fixed-frequency field. Line-start permanent-magnet motors combine a starting cage with magnets, providing another specialized solution.
Once synchronized, the machine is dynamically rather than rigidly locked. A simplified mechanical balance is
where is combined rotational inertia, is load torque, and represents loss torque. A sudden load increase initially produces deceleration, increasing rotor displacement relative to the stator field. The resulting increase in electromagnetic torque can restore equilibrium, but the rotor may oscillate around its new operating angle. These oscillations are commonly called hunting.
Damper windings oppose speed deviations by producing induced currents and damping torque. Drive controls can also provide active damping. If the disturbance is too large, the rotor may lose synchronism, producing severe current and torque oscillations. Protection systems therefore consider overload, stalled starting, loss of field, pole slipping, and excessive starting duration. Mechanical shaft resonances must also be distinguished from electromagnetic hunting, since their frequencies and remedies can differ.
Electronic drives and torque control
Modern synchronous drives use power electronics to make stator frequency, voltage, and current controllable quantities. A common arrangement rectifies an alternating-current supply to a direct-current link and then uses a power inverter to synthesize variable-frequency output. In battery-powered equipment, the direct-current source may feed the inverter directly. Semiconductor switching and pulse-width modulation produce the required fundamental currents, accompanied by switching-frequency ripple.
High-performance control usually expresses measured phase currents in coordinates that rotate with the rotor. In field-oriented control, the direct axis is aligned with the rotor excitation or another defined rotor magnetic axis, while the quadrature axis is perpendicular to it. Mathematical transformations convert three-phase quantities into approximately steady components and . Separate current regulators can then control flux-related and torque-related behavior much more directly than independent regulation of the original sinusoidal phase currents.
For a sinusoidal permanent-magnet machine, a common torque expression is
where is the number of pole pairs, is permanent-magnet flux linkage, and and are direct-axis and quadrature-axis inductances. This form uses the usual amplitude-invariant transformation and peak-valued current components. The first term represents magnet torque and the second reluctance torque. Different coordinate normalizations change numerical factors, so equations and current definitions must be used consistently.
For a nonsalient surface-magnet motor, and are approximately equal, making torque predominantly proportional to . Interior-magnet machines can use both torque components. Maximum-torque-per-ampere control selects a current-vector angle that produces the required torque with reduced current magnitude. At higher speeds, increasing back electromotive force approaches the inverter voltage limit. Field-weakening control introduces an appropriate direct-axis current to reduce effective flux linkage and extend the operating range, subject to current, heating, and demagnetization constraints.
Rotor angle can be measured using a position sensor, such as an encoder or resolver. Sensorless algorithms instead estimate position from measured voltages and currents, using back electromotive force, machine models, or responses to injected signals. Back-electromotive-force estimation becomes difficult near zero speed because the available signal diminishes. Saliency-based signal injection can address some low-speed conditions, but its effectiveness depends on machine geometry, saturation, noise, and implementation.
The drive normally contains nested control loops: fast current regulation, slower speed regulation, and sometimes an outer position loop. Negative feedback rejects disturbances, while feedforward terms compensate predictable coupling. Parameter errors, sampling delays, inverter voltage errors, and magnetic saturation affect control accuracy. When the inverter permits reverse power flow, the same machine can generate electrical energy during regenerative braking.
Efficiency, thermal limits, and mechanical constraints
Synchronous-motor efficiency is the ratio of useful shaft output to total electrical input, with excitation and auxiliary supplies included where the specified measurement boundary requires them. The loss balance includes stator conductor losses, rotor excitation losses where present, magnetic-core losses, bearing friction, windage, and additional load-dependent losses. For a balanced three-phase stator, a basic copper-loss expression is
where is the resistance of one phase at its actual operating temperature.
Permanent-magnet and synchronous reluctance rotors avoid continuous rotor field-winding copper loss. This can improve efficiency and reduce rotor heating, but does not make rotor losses zero. Spatial harmonics, inverter switching, and time-varying fields can induce eddy currents in magnets, sleeves, and rotor steel. Wound-field machines require excitation power but offer adjustable rotor flux, which can be useful across different loads and speeds. Comparisons therefore depend on duty cycle, size, cooling, and control strategy rather than motor category alone.
Core losses arise mainly from magnetic hysteresis and eddy currents and depend on frequency, flux density, material, lamination thickness, and waveform. High-frequency operation can make these losses important even when shaft torque is modest. Inverter-fed windings also experience harmonic current and high-frequency effects in their conductors. Detailed loss prediction commonly combines electromagnetic calculation, material measurements, thermal models, and testing rather than relying on a single efficiency number.
Cooling may use shaft-mounted fans, separately powered blowers, liquid jackets, or more specialized internal arrangements. Low-speed operation is a particular challenge when ventilation depends on a shaft-mounted fan: current-related heating may remain high while cooling airflow falls. Thermal design must protect winding insulation, bearings, magnets, adhesives, and rotor retaining components. Magnet temperature can affect flux strength, and excessive opposing magnetic field at unfavorable temperature can cause irreversible demagnetization.
Mechanical limits become especially important in high-speed designs. Centrifugal loading acts on magnets, rotor bridges, pole attachments, and retaining sleeves. Bearing selection, shaft critical speeds, balance quality, and torsional resonances constrain the speed range. Rolling bearings also require appropriate lubrication and load management. Common-mode voltages from some inverter arrangements can drive bearing currents, creating electrical damage unless the overall installation limits those current paths.
Acoustic noise and vibration result from electromagnetic force harmonics, torque ripple, mechanical imbalance, and structural resonances. Slot and pole combinations, rotor skew, magnet shaping, and current-waveform design influence these effects. Cogging torque is a specific no-current interaction between permanent magnets and stator slotting; it differs from torque ripple caused by energized windings. In precision equipment, these distinctions matter because a motor with high average efficiency can still produce unacceptable speed variation, vibration, or positioning error.
Industrial, transport, and precision applications
Large wound-field synchronous motors are used where substantial power, nearly constant speed, and controllable reactive-power exchange are valuable. Applications include compressors, pumps, fans, and grinding mills. A many-pole construction can drive a slow load directly, avoiding a large reduction gearbox. At the other extreme, higher-speed synchronous machines can suit compressor duties. Selection depends on the load’s torque-speed characteristic, starting requirements, supply strength, maintenance arrangements, and the economic value of efficiency and power-factor control.
Grinding mills illustrate the importance of torque rather than power alone. Since mechanical power is , low rotational speed requires high torque for a given power rating. Large-diameter ring motors can apply torque around the mill structure rather than through a conventional high-speed shaft and gearbox. Such installations integrate motor design with structural mechanics and drive control; their low speed does not imply a lightly loaded electromagnetic system.
In an electric vehicle, permanent-magnet and wound-field synchronous machines provide controllable traction torque over a wide speed range. Interior-magnet designs can combine magnet and reluctance torque, while field weakening extends operation above the voltage-limited base-speed region. Regeneration allows some vehicle kinetic energy to return to the battery, subject to battery acceptance, inverter ratings, traction conditions, and braking-system coordination. Induction motors remain an important alternative, so synchronous operation is one of several traction architectures rather than a universal requirement.
Permanent-magnet synchronous motors are also used in variable-speed compressors for air conditioning, heat pumps, and refrigeration. Matching compressor speed to demand can reduce repeated on-off cycling and improve system operation at part load. The resulting energy performance depends on the refrigerant circuit, heat exchangers, ambient conditions, and controls as well as the motor. Similar integrated design applies to pumps and fans, where fluid-system characteristics strongly influence the benefit of speed variation.
Servo applications in robotics, machine tools, and automation emphasize torque response, low inertia, smooth motion, and position accuracy. A permanent-magnet motor combined with an encoder and electronic drive can operate as a precise actuator. Overall accuracy still depends on bearings, transmission compliance, backlash, structural vibration, and sensor resolution. Direct-drive arrangements remove transmission backlash but may require larger motor diameter, more demanding cooling, or higher-resolution feedback.
Small synchronous motors have historically served clocks, timers, record players, and other devices requiring a stable relationship between electrical frequency and mechanical speed. Their accuracy depends on the frequency source, not solely on motor construction. Separately, synchronous condensers serve electrical grids without substantial useful shaft output, supplying or absorbing reactive power and contributing rotating inertia and fault-current capability. These grid-support functions use the same basic synchronous-machine principles but represent a distinct operating purpose from driving a mechanical load.
Historical development and continuing engineering challenges
Synchronous motors developed from the nineteenth-century investigation of electromagnetic rotation and alternating-current power. During the 1880s, Galileo Ferraris and Nikola Tesla independently developed important rotating-field concepts. Tesla’s alternating-current motor patents of 1888 formed part of the emerging polyphase system. This history overlaps with that of induction motors: the rotating field is common to both, while rotor excitation and the mechanism of torque production distinguish their steady operating behavior.
As alternating-current networks expanded, synchronous machines became established both as motors and as generators. Their fixed relationship between frequency, pole count, and shaft speed suited duties requiring constant speed, while adjustable excitation provided a means of influencing power factor. Large industrial synchronous motors developed alongside improved insulation, magnetic materials, excitation equipment, and starting methods. Their adoption was especially attractive where operating savings and reactive-power benefits justified greater installation complexity than a basic induction-motor arrangement.
Electronic power conversion transformed the significance of synchronism. Instead of accepting the speed imposed by a fixed-frequency network, a converter-fed drive could command the rotating-field frequency. Developments in thyristors and, later, power transistors made controlled synchronous drives practical over expanding power ranges. Some very large drives use load-commutated converter arrangements suited to wound-field synchronous machines, while transistor-based voltage-source inverters became central to many smaller and medium-power servo and traction systems.
Vector-control methods and digital processing further separated torque control from the limitations of direct line operation. Mathematical models in rotating coordinates became implementable in real time, allowing accurate current regulation, rapid torque response, and controlled operation through wide speed ranges. The resulting motor-drive system is not merely a motor attached to a variable supply: electromagnetic geometry, sensors, switching strategy, software, cooling, and mechanical loading are designed as interacting components.
Magnet development also changed machine design. Samarium-cobalt materials and, subsequently, neodymium–iron–boron magnets enabled compact permanent-magnet machines with high magnetic loading. Neodymium–iron–boron magnets emerged in the early 1980s and became important in numerous motor applications. Their use introduced design trade-offs involving magnet retention, elevated-temperature performance, demagnetization, manufacturing cost, and material supply. Ferrite-based and reduced-magnet designs address different combinations of these constraints rather than reproducing rare-earth-magnet performance without compromise.
Continuing development focuses on performance across complete operating cycles, not simply peak torque or rated efficiency. Synchronous reluctance machines, magnet-assisted rotors, wound-field traction machines, and improved cooling systems offer different routes to reducing losses or dependence on particular materials. Higher switching frequencies and wide-bandgap semiconductors can improve some aspects of drive control and packaging, while also increasing demands on insulation, electromagnetic compatibility, and high-frequency loss prediction. Accurate modeling of saturation, local rotor stress, transient temperature, and fault behavior remains essential as machines become more compact and operate over wider speed ranges.