Reactive power is a quantity used in electrical engineering to describe an aspect of power exchange in alternating-current circuits. For sinusoidal voltage and current, it is the product of their root-mean-square magnitudes and the sine of their phase difference. Unlike active power, which represents the average rate of net energy transfer, reactive power characterizes the quadrature component of the voltage–current relationship. Its unit is the var, commonly expressed in kilovars or megavars.
Reactive power is essential to the operation of an electrical grid because it affects voltage, current, network losses, and the usable capacity of generators, transformers, and transmission lines. Motors and transformers commonly absorb reactive power, while capacitors and appropriately controlled generators or electronic converters can supply it. Although ideal reactive elements consume no net energy over a complete cycle, the currents associated with their operation produce losses in real conductors and equipment.
The familiar reactive-power equations apply most directly to sinusoidal steady-state operation. Unbalanced systems, distorted waveforms, and converter-dominated networks require additional distinctions between fundamental-frequency reactive power, distortion-related quantities, and instantaneous power. These distinctions matter both for physical interpretation and for metering, control, and commercial settlement.
Sinusoidal definition and power relationships
For a single-phase sinusoidal circuit, let the voltage and current be
where and are root-mean-square values, is angular frequency, and is the angle by which current lags voltage. Multiplication gives the instantaneous power:
The average over a complete cycle is the active power,
while reactive power is defined as
Active power is measured in watts and reactive power in vars. Both have the physical dimension of power, but different unit names preserve an important distinction between the quantities. The apparent power is , measured in volt-amperes. Under these sinusoidal conditions,
These relationships form the conventional power triangle: active and reactive power are perpendicular components, and apparent power is their resultant magnitude. The triangle is a representation of the electrical quantities, not a statement that reactive power is a separate stream of fuel or stored energy.
Using root-mean-square phasors, complex power is
where the asterisk denotes complex conjugation and . This use of a complex number makes voltage–current phase relationships convenient to calculate. Under the passive sign convention, current enters the terminal designated positive for voltage. An inductive load then absorbs positive reactive power, while a capacitive load absorbs negative reactive power. A generator described as injecting reactive power uses a network-oriented convention, so the sign must always be interpreted with its stated reference direction.
The power factor is . For sinusoidal voltage and current, it equals ; lagging power factor normally indicates inductive behavior and leading power factor capacitive behavior. For example, a load taking at a lagging power factor of 0.8 draws and absorbs . Its current is therefore greater than that required to deliver the same active power at unity power factor.
Reactive power is not identical to the entire oscillating part of instantaneous power. Even a purely resistive single-phase load has a twice-frequency power pulsation, although its reactive power is zero. Expanding the instantaneous-power expression gives
which shows how both active and reactive components contribute to the waveform. This distinction prevents the common but inaccurate identification of every power oscillation with reactive power.
Energy exchange in inductors, capacitors, and electrical machines
The physical interpretation of reactive power begins with energy storage in electric and magnetic fields. An ideal inductor stores energy according to
where is inductance. An ideal capacitor stores
where is capacitance. During periodic operation, each element alternately accepts energy from the circuit and returns it. Its net energy absorption over a complete cycle is zero, even though its instantaneous power generally is not.
For an ideal inductor supplied by sinusoidal voltage, current lags voltage by , so and . Its reactance is , giving
For an ideal capacitor, current leads voltage by . Using the same passive convention,
At a fixed frequency and capacitance, doubling the applied voltage therefore quadruples the magnitude of capacitive reactive power. For either ideal element alone under sinusoidal steady state, the magnitude of reactive power also equals angular frequency multiplied by the maximum stored field energy.
Real components depart from these idealizations. An inductor has winding resistance and may have magnetic-core losses; a capacitor has dielectric losses and equivalent series resistance. These losses consume active power. Reactive power itself is not dissipated as heat, but the current accompanying it contributes to heating in every resistive part of the circuit. A statement that a device is “purely reactive” is thus an approximation, often useful for analysis but never exact for physical equipment.
Many industrial loads require a substantial magnetizing current. An induction motor establishes a rotating magnetic field through currents in its stator and rotor. Its electrical input supplies mechanical output and losses as active power, while the magnetizing process contributes to reactive-power demand. At light mechanical load, the magnetizing component remains significant even as active input falls, which is one reason an induction motor’s power factor commonly deteriorates when lightly loaded.
An electrical transformer similarly draws magnetizing current and absorbs reactive power through its leakage reactance when carrying load. Its excitation behavior becomes strongly nonlinear as the core approaches saturation. Reactive demand can consequently increase sharply under excessive voltage relative to frequency. This behavior is important during abnormal operating conditions and transformer energization.
A synchronous generator differs because its field excitation can be controlled. At a given active-power output and terminal voltage, stronger excitation generally enables it to supply more reactive power to the network; reduced excitation can make it absorb reactive power. This controllability makes synchronous machines important voltage-regulating resources, subject to winding-heating, excitation, and stability limits.
Three-phase systems, current loading, and network flows
In a balanced three-phase system, total active and reactive powers can be written using line-to-line voltage and line current :
The corresponding apparent power is
These expressions assume balanced sinusoidal conditions. They apply to balanced star- or delta-connected equipment when line and phase quantities are used consistently. In a balanced three-phase load, the twice-frequency instantaneous-power pulsations of the individual phases cancel. Total instantaneous active-power transfer can therefore be constant even when reactive power is nonzero.
For fixed active power and voltage, reactive demand increases current:
A load at draws approximately at unity power factor. At a power factor of 0.8, it draws approximately and absorbs . If conductor resistance is unchanged, the associated resistive losses are about times as large. This comparison concerns network losses at the same delivered active power; it does not imply that the load’s useful energy consumption rises by the same proportion.
Equipment ratings frequently reflect current and voltage limits rather than active power alone. A transformer rated at cannot generally deliver while also carrying substantial reactive power without exceeding its rating. At a power factor of 0.8, the same apparent-power loading corresponds to . Reducing unnecessary reactive flow can therefore release capacity in transformers, cables, and switchgear without increasing their thermal ratings.
In transmission networks, both series inductance and shunt capacitance matter. A line carrying current absorbs reactive power through its series reactance, approximately in proportion to . At the same time, its shunt capacitance supplies reactive power, approximately in proportion to voltage squared. A lightly loaded overhead line may consequently be a net reactive-power source, while a heavily loaded line is commonly a net absorber.
For an ideal lossless line, these effects balance at its surge impedance loading, given approximately by
where is the line’s characteristic impedance. This is a useful operating reference, not a universal thermal or stability limit. Underground and submarine cables have much higher capacitance than typical overhead lines, so their charging currents and reactive-power production can be especially important.
Reactive power is therefore not strictly conserved as it passes through a network. Series reactances absorb it, while capacitances supply it. A system-wide balance must include these network contributions as well as loads, generators, and compensation equipment.
Voltage regulation and voltage stability
Reactive power and voltage are closely coupled in many power networks. For a simplified radial circuit with resistance , reactance , and receiving-end voltage magnitude , an approximate voltage-drop relationship is
using consistent per-phase quantities and neglecting higher-order effects. Positive and here represent power delivered to the receiving-end load. Where is large relative to , reactive flow has a strong influence on voltage magnitude. In lower-voltage distribution circuits, resistance can be comparable to reactance, making active-power flow important as well.
This relationship explains why reactive support is usually most effective near the location where it is needed. Supplying a distant inductive load from a remote source requires reactive current to traverse intervening equipment. That current produces additional voltage drop, resistive losses, and reactive absorption in series inductances. There is no absolute boundary preventing reactive-power transfer over long distances, but local support often achieves the same voltage objective with less network burden.
For a simplified lossless connection between two buses, active-power transfer depends strongly on their voltage-angle difference, while reactive exchange depends strongly on voltage magnitudes. This produces the familiar engineering approximation that active power is associated with angle and frequency, and reactive power with voltage. The approximation supports many control designs, but it is not exact: the variables remain coupled, especially in weak or resistive networks.
Voltage stability concerns a system’s ability to maintain acceptable voltages following disturbances or changes in operating conditions. One important mechanism arises when declining voltage causes a load or its controls to draw more current in an attempt to maintain active power. Greater current increases network losses and voltage drop, which can cause further decline. Meanwhile, fixed capacitors become less effective because their reactive output falls with voltage squared.
Generator limits can intensify this process. A generator’s automatic voltage regulator may initially raise excitation to support voltage, but sustained operation can encounter field-current or stator-current limits. Once those limits act, the machine cannot continue increasing reactive output as though it were an unlimited voltage source. Transformer tap changers can also restore downstream load voltage while increasing the burden on an already stressed transmission network.
Engineers study these mechanisms using power-flow calculations, dynamic simulations, and voltage-versus-power or reactive-power-versus-voltage curves. A “nose” on a steady-state voltage–power curve can indicate the disappearance of an equilibrium solution in the model. Actual collapse, however, can also depend on motor stalling, protective relays, excitation limiters, and the timing of controls.
Reactive reserve consequently has a locational and dynamic character. A large aggregate reserve does not guarantee that a constrained area has adequate support. Its usefulness depends on where it is connected, how quickly it responds, and whether it remains available during depressed voltage or equipment outages.
Compensation equipment and its operating characteristics
Reactive-power compensation changes the reactive exchange of a load or network to achieve an operating objective, such as reducing current, maintaining voltage, or improving transfer capability. Shunt capacitor banks are widely used because they provide capacitive reactive power with relatively low losses and no rotating machinery. They may be installed at industrial switchboards, distribution feeders, or an electrical substation, either permanently connected or divided into switched stages.
For a sinusoidal load whose active power remains constant, the capacitive compensation required to change power factor from to is
For example, improving a load from a lagging power factor of 0.75 to 0.95 requires approximately of capacitive compensation. This is a nominal calculation: actual output depends on voltage, frequency, component tolerances, and the available switching stages. If the load later decreases while all capacitors remain connected, the installation may become overcompensated and export reactive power.
Shunt reactors perform the opposite function. They absorb inductive reactive power and are commonly applied to long transmission lines and high-voltage cables during light-load conditions. They help control voltage rise, including the Ferranti effect, in which the receiving-end voltage of a lightly loaded line can exceed its sending-end voltage. Series capacitors serve a different purpose: by offsetting part of a line’s series inductive reactance, they alter power-transfer characteristics. Their application requires specialized protection and analysis of possible interactions with generators and controls.
A synchronous condenser is a synchronous machine operated without a useful mechanical load. Adjusting its excitation changes whether it supplies or absorbs reactive power. It also contributes rotating inertia and fault current, characteristics that distinguish it from a simple capacitor bank. Its disadvantages include mechanical losses, auxiliary systems, maintenance requirements, and the need for a starting arrangement.
A static var compensator, or SVC, uses thyristor-controlled or thyristor-switched branches, usually involving reactors and capacitors, to vary shunt susceptance rapidly. A static synchronous compensator, or STATCOM, instead uses a voltage-source converter connected through a coupling reactance. It regulates current by controlling the converter’s voltage relative to the network.
Their low-voltage behavior is an important distinction. For an SVC operating at a fixed susceptance limit, reactive output falls approximately with voltage squared. A current-limited STATCOM can maintain approximately rated reactive current over part of its low-voltage operating range, so its reactive power falls roughly in proportion to voltage rather than voltage squared. Actual performance depends on converter limits, protection settings, and control design.
Capacitor switching can also produce transient currents and overvoltages. Coordination with reactors, switching equipment, and protection is therefore part of compensation design rather than a separate afterthought.
Electronic converters and renewable generation
Modern power electronics allows reactive current to be controlled without relying on a directly connected synchronous machine. A grid-connected inverter synthesizes an alternating voltage from a direct-current link and regulates the resulting current through an interface filter or reactor. In a reference frame aligned with grid voltage, current can be separated into components associated approximately with active and reactive power. Their exact signs and scaling depend on the transformation convention.
This control capability is central to many solar and wind installations. A photovoltaic inverter can regulate reactive exchange while delivering active power from its array, provided it has adequate current and voltage capability. Many modern wind turbines similarly use converters to control reactive power independently of mechanical input within their operating limits. A doubly fed induction generator retains a direct stator connection to the grid and uses a converter in its rotor circuit, whereas a full-converter turbine routes its generated electrical output through the converter.
Active and reactive capability share hardware limits. A simplified apparent-power constraint is
An inverter rated at and delivering would, under this constraint alone, have up to available in either reactive direction. Real capability may be narrower or asymmetric because of terminal voltage, direct-current voltage, temperature, filter design, and semiconductor limits. During low voltage, current limits become particularly important because a given reactive current produces less reactive power.
If an inverter operates near full active-power rating, providing additional reactive support may require active-power curtailment or a larger converter. At night, a photovoltaic installation may be able to operate as a reactive-power resource, but only if its hardware, auxiliary supply, controls, and operating arrangements permit it. Such operation still consumes active power to cover losses; it is not an inherent capability of every solar installation.
Converter controls also determine behavior during disturbances. Grid-following converters normally synchronize to an existing voltage waveform and control injected current. Grid-forming converters instead regulate an internal voltage waveform and can participate more directly in establishing local voltage and frequency. Reactive-power droop, voltage regulation, and current-limiting logic must remain coordinated in either case, especially in electrically weak systems.
Similar distinctions arise in high-voltage direct-current transmission. Conventional line-commutated converter stations consume substantial reactive power and typically require filters and compensation. Voltage-source converter stations can generally control active and reactive exchange more independently, within their limits. The direct-current link itself does not carry fundamental-frequency AC reactive power; reactive exchanges occur at its AC terminals.
Converter capability therefore expands the available means of voltage control, but nameplate megavar capacity alone does not describe performance. Response speed, fault behavior, current priority, and interaction with neighboring controls are also decisive.
Distorted waveforms, unbalance, and measurement
The simple identity does not generally describe all nonactive effects when voltage or current is nonsinusoidal. For arbitrary periodic waveforms, active power remains the average of instantaneous power:
For a single-phase circuit, apparent power remains the product , and total power factor remains . However, a single phase angle no longer fully describes the relationship between waveforms containing multiple frequencies.
Harmonics are components at integer multiples of the fundamental frequency. Rectifiers, switched electronic loads, magnetic saturation, and other nonlinear processes can produce harmonic currents. If the supply voltage is nearly sinusoidal but current is strongly distorted, the fundamental current can be almost in phase with voltage while the total power factor remains low. The additional root-mean-square current increases apparent power without a corresponding increase in useful average power.
Under the simplifying assumption of sinusoidal voltage and current containing a fundamental plus harmonics, with no direct-current component,
where is the fundamental displacement angle and is current total harmonic distortion relative to the fundamental. This separates displacement power factor from the reduction caused by current distortion. A capacitor selected solely to correct the fundamental phase angle does not remove harmonic current and may amplify it if a resonance is created.
Several theories distinguish reactive, distortion, and other nonactive quantities. Constantin Budeanu proposed a harmonic-based reactive-power definition in 1927, summing signed reactive contributions across harmonics. Stanisław Fryze developed a time-domain decomposition in 1932 based on separating current into active and nonactive components. Later instantaneous-power theories, including the three-phase - theory associated with Hirofumi Akagi and colleagues in the 1980s, supported real-time compensation and active-filter control. These approaches serve different analytical purposes and do not yield one universally interchangeable reactive quantity under every waveform condition.
Unbalanced three-phase systems add another complication. Phase voltages and currents may differ, and negative- or zero-sequence components can increase losses or heating. A single aggregate power-factor value can conceal substantial phase-specific problems. Standards such as IEEE 1459 distinguish fundamental, nonfundamental, positive-sequence, and unbalance-related quantities to support more precise interpretation.
Meters consequently need a defined measurement method. A fundamental-frequency reactive-energy register is not necessarily equivalent to a register based on another waveform-processing algorithm. Sampling rate, filtering, phase calibration, and harmonic response affect the result. Reactive energy is commonly recorded in var-hours or kilovar-hours, representing time-integrated reactive power under the meter’s convention, not a stock of energy that can be extracted as useful work.
Compensation for distorted systems may require tuned or detuned passive filters, active filters, or changes to converter controls. The appropriate quantity to measure depends on whether the objective is billing, thermal loading, harmonic mitigation, or dynamic control.
System operation, capability limits, and economic treatment
Power-system operators manage reactive power to maintain acceptable voltages in normal operation and after credible disturbances. Relevant resources include generator excitation systems, transformer tap changers, capacitor banks, shunt reactors, synchronous condensers, and converter-based devices. They act on different timescales: electronic current control can respond rapidly, generator excitation acts dynamically, and mechanically switched equipment or tap changers usually provides slower adjustment.
An optimal power flow calculation can coordinate these resources subject to network equations and operating constraints. A common objective is to reduce losses or operating cost while keeping voltages, line currents, generator outputs, and control settings within limits. Reactive optimization is nonlinear, and switched capacitor stages or transformer taps introduce discrete choices. An economically attractive normal operating point may therefore differ from one that preserves more reactive reserve for contingencies.
Generator capability diagrams define feasible combinations of active and reactive output. Stator-current limits constrain apparent power; rotor field-current limits commonly restrict strongly overexcited operation; and underexcited operation may be limited by end-region heating or stability considerations. These boundaries depend on machine design and operating conditions. A generator’s unused active-power capacity cannot simply be counted as an equal amount of available reactive capacity.
Reactive capability also has an opportunity cost. A generator or converter required to supply additional reactive power may have to reduce active output, incur higher losses, or operate closer to a limiting condition. Conversely, maintaining a local reactive resource can reduce transmission losses or avoid a network reinforcement. The economic value depends on location and operating conditions rather than solely on the number of megavars produced.
Electricity tariffs may therefore include low-power-factor penalties, apparent-power demand charges, or reactive-energy charges. These mechanisms reflect different commercial arrangements and should not be treated as interchangeable. A kilovar-hour charge measures accumulated reactive exchange under a defined convention, whereas a kilovolt-ampere demand charge responds to peak apparent-power use. Some systems also compensate generators or other resources for voltage-control capability and availability rather than only for measured reactive-energy output.
Operational coordination is increasingly important in distribution systems with many independently controlled inverters. A local voltage controller may command reactive absorption to reduce a voltage rise caused by solar export, while a capacitor controller may simultaneously seek to improve feeder power factor. Without coordinated objectives, the devices can counteract one another, increase reactive circulation, or switch unnecessarily.
Utilities use supervisory control and data acquisition, network models, telemetry, and distribution-management systems to coordinate these actions. Grid-connection requirements can specify reactive capability, voltage-control modes, response settings, and behavior during disturbances. Such requirements distinguish between equipment being physically capable of reactive exchange and that capability being available, enabled, measurable, and dependable at the network connection point.