A film capacitor is a capacitor in which a thin plastic film forms the insulating layer, or dielectric, between conductive electrodes. The electrodes may be separate metal foils or metal coatings deposited directly onto the film. Most film capacitors are nonpolarized and can operate with either voltage polarity, subject to their specified direct-current, alternating-current, and pulse ratings. Their relatively low losses, high insulation resistance, and range of voltage and current capabilities make them important in precision electronics, motor circuits, and power electronics.
Operating principle
Like other capacitors, a film capacitor stores energy in an electric field. For an idealized parallel-plate structure,
where is capacitance, is the effective overlapping electrode area, is dielectric thickness, is the permittivity of free space, and is the film’s relative permittivity.
Practical components obtain a large electrode area by winding long film strips into a compact roll or stacking many layers. Thinner films increase capacitance per unit volume but place greater demands on film uniformity, manufacturing cleanliness, and electric-field control.
The energy stored at voltage is approximately
The dielectric is a polymer, rather than the oxide layer used in an electrolytic capacitor or the ceramic body used in a ceramic capacitor. This distinction strongly influences capacitance density, electrical losses, stability, and failure behavior.
Construction and manufacture
Two principal electrode constructions are used.
Film-and-foil construction
In a film-and-foil capacitor, separate metal foils alternate with insulating film layers. The relatively thick electrodes can carry substantial pulse currents, making this construction useful where high peak current or rapid voltage change is important.
A dielectric puncture can produce a persistent short circuit because the foil around the fault does not readily clear away. Film-and-foil capacitors therefore do not inherently exhibit the self-healing behavior associated with suitably designed metallized films.
Metallized-film construction
In a metallized-film capacitor, a very thin conductive coating, commonly aluminum or zinc-based metallization, is deposited onto the polymer film. Uncoated margins and offset layers prevent the two electrodes from contacting one another. Sprayed-metal end connections join the exposed electrode edges to external terminals.
Metallized construction generally provides a smaller component for a given capacitance and voltage rating than comparable film-and-foil construction. Its thin electrodes, however, introduce trade-offs between electrical resistance, current capacity, and fault-clearing behavior. Metallization may be made thicker near the contacts or patterned into segments to manage these trade-offs.
Both constructions may use wound or stacked elements. Packages range from small resin-encapsulated components for printed circuit boards to large enclosed power capacitors. Some designs are dry, while others use impregnants to fill voids and improve electrical or thermal performance.
Dielectric materials
The film material determines much of a capacitor’s electrical and thermal behavior. The characteristics below are general tendencies; actual performance also depends on film thickness, electrode design, packaging, and operating conditions.
| Material | Typical characteristics | Common uses |
|---|---|---|
| Polypropylene (PP) | Low dielectric loss, high insulation resistance, relatively low dielectric absorption | Power conversion, resonant circuits, pulse circuits, precision applications |
| Polyethylene terephthalate (PET), or polyester | Higher relative permittivity than polypropylene, allowing compact construction; generally higher dielectric loss | Coupling, bypassing, timing, and general-purpose electronics |
| Polyethylene naphthalate (PEN) | Useful thermal and processing characteristics for compact designs | Selected surface-mount and higher-temperature applications |
| Polyphenylene sulfide (PPS) | Good dimensional and thermal stability, with relatively low dielectric loss | Surface-mount components and stable electronic circuits |
| Polytetrafluoroethylene (PTFE) | Very low loss and high temperature capability, but relatively costly | Specialized high-temperature and precision applications |
Polystyrene was historically used for low-loss, stable capacitors, particularly in timing and measurement circuits. Its limited tolerance of high processing temperatures restricts its compatibility with many modern assembly methods.
Manufacturer abbreviations such as MKT and MKP commonly identify metallized polyester and metallized polypropylene capacitors, respectively. These markings do not by themselves specify a complete electrical rating.
Electrical characteristics
Capacitance stability
Film capacitors can provide relatively stable capacitance, but stability varies with dielectric material and operating conditions. Temperature, frequency, aging, and absorbed moisture can all affect the measured value.
Many film types exhibit much less capacitance change with applied voltage than high-permittivity ceramic capacitors. This can be useful in timing circuits, analog signal processing, and precision filters.
Losses and heating
Real capacitors dissipate energy through dielectric losses and resistance in electrodes, contacts, and terminals. These effects are often represented by an equivalent series resistance (ESR).
For a sinusoidal current at a specified frequency, an approximate loss relation is
The dissipation factor, often written , expresses losses relative to the reactive behavior. In a simple series model,
where is frequency. ESR and dissipation factor generally vary with frequency and temperature; neither should be treated as a universal constant.
Low-loss polypropylene is particularly useful where substantial alternating current would otherwise cause excessive internal heating.
Pulse current and parasitic inductance
The ideal capacitor relation
shows why a rapid voltage change can produce a large current. Pulse performance depends not only on dielectric strength but also on electrode resistance, end connections, terminals, and internal heating.
Every real capacitor also has parasitic inductance. Above its self-resonant frequency, inductive behavior becomes dominant. Low-inductance winding arrangements and short, wide terminal connections can improve high-frequency performance, but film capacitors do not replace small ceramic components in every high-frequency application.
Dielectric absorption
Dielectric absorption is the partial recovery of terminal voltage after a charged capacitor has been discharged and then left open-circuit. It arises from polarization processes that relax over different timescales.
Its magnitude depends on the film material. It matters in sample-and-hold circuits, integrators, and precision measurements because it can introduce memory-like errors.
Self-healing and failure mechanisms
A major feature of many metallized-film capacitors is self-healing. If a localized dielectric defect breaks down, the resulting discharge can vaporize the very thin metallization around the fault. The cleared area isolates the damaged point, allowing the rest of the capacitor to remain functional.
Self-healing has important limits:
- Each clearing event removes a small amount of active electrode area.
- Repeated events can cause measurable capacitance loss.
- Excessive fault energy can prevent successful clearing or damage surrounding material.
- Self-healing does not prevent every short circuit, open circuit, or enclosure rupture.
Some power capacitors use segmented electrodes with narrow, fuse-like connections that disconnect a defective region. Certain enclosed designs also incorporate pressure-operated disconnectors. These are construction-specific features, not properties of all film capacitors.
Other degradation mechanisms include moisture-related electrode corrosion, deterioration of end contacts, thermal damage, and partial discharges in internal voids under sufficiently high electrical stress. Service life depends on the combined effects of voltage, temperature, ripple current, humidity, and construction; no single lifetime figure applies to the entire category.
Applications
Electronic circuits
Film capacitors are used for signal coupling, timing, integration, and filtering in electronic amplifiers, instrumentation, and control circuits. Their usefulness follows from measurable properties such as stability, leakage, and loss, rather than from a general superiority over every other capacitor technology.
Power conversion and DC links
In power inverters, variable-frequency drives, and some electric vehicles, film capacitors support the DC link between conversion stages. They carry ripple current and provide a local energy reservoir.
Compared with aluminum electrolytic capacitors, film capacitors can offer low losses and substantial ripple-current capability, but generally provide less capacitance per unit volume. Their suitability depends on voltage, required stored energy, thermal conditions, and the converter’s operating strategy.
Snubbers and resonant circuits
Film capacitors appear in snubber networks that limit voltage transients or damp oscillations during switching. They are also used in resonant converters and induction-heating equipment, where repetitive current, low loss, and pulse endurance are important.
These duties occur in switched-mode power supplies and other switching power systems.
AC power and motors
Power film capacitors provide reactive power compensation and improve power factor in electrical installations. Metallized polypropylene is widely used in this role.
Film capacitors are also used as run capacitors in some single-phase induction motors, where they help establish a phase displacement between winding currents. Motor-start capacitors may instead use other technologies, so start and run capacitors are not necessarily interchangeable.
Interference suppression
Specially approved film capacitors suppress electromagnetic interference at mains connections. Safety classifications distinguish, among other things, X capacitors used across supply conductors and Y capacitors used in positions where failure could create an electric-shock hazard, commonly between a supply conductor and protective earth.
A general-purpose film capacitor with a high DC voltage rating is not automatically equivalent to a mains interference-suppression capacitor. Relevant safety classifications include requirements for impulse withstand, endurance, and failure behavior, not merely nominal voltage.
Development and technological limits
Plastic-film capacitors expanded during the mid-twentieth century as thin, consistent polymer films and industrial metallization processes became available. They replaced paper-dielectric capacitors in many applications, although paper and mixed paper-film constructions continued in specialized uses. Improvements in film extrusion, vacuum metallization, electrode patterning, and enclosure design subsequently supported higher electric fields and more demanding power applications.
Their principal limitations remain physical and thermal. Increasing electric field can reduce component size, but also increases stress on the dielectric. Thinner metallization can improve fault clearing while increasing resistance. Higher operating temperature can accelerate deterioration of the film, electrodes, or packaging.
Film capacitors consequently occupy a distinct position among capacitor technologies: they provide a useful combination of voltage capability, low loss, stability, and current handling, while usually sacrificing capacitance density relative to electrolytic capacitors and compactness relative to ceramics in many small-capacitance applications.