A ceramic capacitor is a capacitor in which a ceramic material forms the electrically insulating layer, or dielectric, between conductive electrodes. Ceramic capacitors are generally non-polarized, meaning that neither terminal has a required positive or negative polarity. They are widely used in electronic equipment because they can combine small dimensions, low electrical losses, and useful performance at high frequencies. Their properties vary substantially with ceramic composition: some types provide highly stable capacitance, while others achieve much greater capacitance in a small volume at the cost of sensitivity to temperature, applied voltage, and time.
Operating principle
A ceramic capacitor stores energy in the electric field between its electrodes. For an idealized pair of parallel electrodes, capacitance is
where is the overlapping electrode area, is the dielectric thickness, is the permittivity of free space, and is the ceramic’s relative permittivity.
Capacitance can therefore be increased by enlarging the electrode area, reducing dielectric thickness, or using a material with higher permittivity. Multilayer construction combines many thin dielectric layers and overlapping electrodes within a single component.
For a capacitor whose capacitance is effectively constant, the relationship between stored electric charge and voltage is , and stored energy is
These simple expressions require qualification for high-permittivity ceramics whose capacitance changes significantly with voltage. Their stored energy must be evaluated from the actual charge–voltage relationship rather than from a single nominal capacitance value.
Construction and manufacture
Multilayer ceramic capacitors
The multilayer ceramic capacitor, commonly abbreviated MLCC, is the principal miniature form used in modern electronics. It contains alternating layers of ceramic and internal metal electrodes. Alternate electrodes connect to opposite end terminations, placing the individual capacitive sections electrically in parallel.
If similar active dielectric gaps contribute in parallel, an approximate expression is
Manufacture typically involves preparing fine ceramic powders, forming thin sheets, printing electrode patterns, stacking and laminating the sheets, cutting individual components, removing organic binders, and firing the assembly. During sintering, the ceramic densifies into a mechanically coherent body. External terminations are then applied and commonly plated to provide solderable surfaces.
Many MLCCs use nickel internal electrodes; other designs use precious-metal electrode systems. Ceramic chemistry and firing atmosphere must be controlled together to preserve both electrode integrity and dielectric insulation.
Most miniature MLCCs are intended for surface-mount technology. They are mounted directly onto conductive pads on a printed circuit board. Capacitance, voltage rating, and package size are interdependent: a smaller package does not necessarily provide the same effective capacitance under operating conditions as a larger component with the same nominal rating.
Disc and specialized forms
A ceramic disc capacitor generally consists of a ceramic disc with electrodes on its opposite faces, attached leads, and a protective coating. Leaded multilayer constructions also exist.
Specialized ceramic capacitors include high-voltage discs, feedthrough capacitors, and larger radio-frequency power components. Their geometry and materials are adapted to requirements such as insulation distance, current handling, heat dissipation, and low connection inductance.
Dielectric classes
Ceramic capacitors are commonly divided into two main dielectric classes. Classification terminology varies between standards systems, so a class number alone is not a complete specification.
Class 1: stable, low-loss dielectrics
Class 1 ceramics offer relatively low dielectric loss and predictable temperature behavior. Their permittivity is generally lower than that of Class 2 materials, so they provide less capacitance for a given volume.
The best-known designation is C0G, often also called NP0. C0G specifies a temperature coefficient of capacitance of approximately parts per million per degree Celsius over its specified temperature range. Other Class 1 formulations provide deliberately chosen temperature coefficients.
Typical characteristics include:
- Small capacitance changes with temperature.
- Little dependence on applied DC voltage.
- Negligible dielectric aging compared with Class 2 ceramics.
- Low loss and good suitability for resonant circuits.
Class 1 capacitors are used where capacitance stability matters, including oscillators, precision timing networks, and frequency-selective circuits.
Class 2: high-permittivity dielectrics
Class 2 ceramics commonly use formulations based on barium titanate. Their high permittivity is associated with ferroelectric behavior. They can provide much higher capacitance per unit volume than Class 1 materials, but their capacitance is more dependent on operating conditions.
Common temperature-characteristic codes include:
| Code | Specified temperature range | Permitted capacitance change with temperature |
|---|---|---|
| X7R | −55 to +125 °C | ±15% |
| X5R | −55 to +85 °C | ±15% |
| Y5V | −30 to +85 °C | +22% to −82% |
These limits describe temperature behavior under specified test conditions. They do not include every source of capacitance variation, such as initial tolerance, DC bias, or aging. An X7R designation therefore does not mean that capacitance remains within ±15% of its nominal value under all operating conditions.
Class 2 capacitors are widely used for supply decoupling, filtering, and other functions where compactness is more important than precise capacitance.
Electrical behavior
DC-bias dependence
Many Class 2 MLCCs lose a substantial fraction of their measured small-signal capacitance when a DC voltage is applied. The magnitude of this DC-bias effect depends on the dielectric formulation, layer thickness, package, capacitance, and applied voltage.
Consequently, a capacitor can operate below its rated voltage while providing far less capacitance than its nominal marking suggests. Voltage rating specifies an operating limit under stated conditions; it is not a guarantee of capacitance retention. Manufacturer bias curves or component models describe this behavior more usefully than dielectric code alone.
Class 1 capacitors generally show much smaller voltage dependence.
Aging and temperature history
Class 2 ceramics exhibit dielectric aging: after cooling below their relevant transition region, their capacitance typically decreases approximately logarithmically with elapsed time. Aging rates are often expressed as a percentage change per decade of time, such as from 10 to 100 hours.
Heating the material sufficiently can reset much of this aging process. Soldering can therefore alter the capacitance measured shortly afterward, with aging resuming during subsequent storage or operation. Aging is distinct from irreversible damage or ordinary component wear.
Losses and parasitic elements
A practical ceramic capacitor includes effective series resistance and inductance as well as capacitance. A simplified series model has impedance
where is equivalent series resistance, is equivalent series inductance, and is angular frequency.
Below its self-resonant frequency, the component behaves predominantly as a capacitor. Above that frequency, its inductive behavior becomes dominant. In the simple model,
Package construction, connection geometry, and board layout all affect high-frequency performance. Low intrinsic resistance does not eliminate heating: sufficiently large alternating currents and dielectric losses can still produce significant temperature rise.
Microphonic and acoustic effects
Some high-permittivity ceramics exhibit piezoelectric and electrostrictive effects. Mechanical vibration can produce an electrical disturbance, while an applied varying voltage can cause mechanical deformation.
Through coupling to the circuit board, these effects can generate audible noise or introduce interference into sensitive signal paths. Stable Class 1 dielectrics generally exhibit much less of this behavior.
Applications
Ceramic capacitors serve several distinct roles:
- Supply decoupling: placed near integrated circuits to provide local transient current and reduce supply-voltage disturbances.
- Filtering: used in signal filters and power networks to attenuate unwanted frequency components.
- Signal coupling: pass alternating signals while blocking steady DC, although voltage-dependent capacitance can introduce distortion in some applications.
- Resonance and timing: stable Class 1 types establish frequencies and time constants.
- Power conversion: used in DC–DC converters, switched-mode power supplies, and other power-electronic circuits for filtering and suppression of switching disturbances.
- Interference suppression: specialized constructions reduce conducted high-frequency noise, including feedthrough types at enclosure boundaries.
Ceramic capacitors often complement electrolytic capacitors. Electrolytic types can provide economical bulk capacitance, while small ceramic components can offer lower connection inductance and better high-frequency performance. Connecting different capacitor types or values in parallel can also produce resonances, so their combined behavior is not simply the sum of ideal capacitances.
Reliability and limitations
Ceramic is hard but brittle. Board bending, mechanical shock, and thermal stress can crack an MLCC. Some cracks reduce insulation resistance or create a short circuit, particularly if moisture or conductive contamination reaches internal structures. Flexible terminations and mechanically accommodating package designs can reduce vulnerability but do not eliminate every failure mechanism.
Rapid temperature changes during assembly can also cause damage. Electrical overstress may lead to dielectric breakdown, and elevated temperature, humidity, and sustained electric field can affect long-term insulation reliability.
A standard ceramic capacitor is not automatically suitable for connection across an AC supply or between a supply conductor and protective earth. Such positions use appropriately certified X- or Y-class safety capacitors. These safety classifications are separate from dielectric codes such as X7R.
Historical development
Ceramic capacitors developed through improvements in ceramic dielectrics, electrode materials, and manufacturing processes. Early constructions included single-layer and disc devices. High-permittivity titanate ceramics enabled much greater capacitance in compact components, while multilayer manufacture substantially increased usable electrode area.
The expansion of surface-mount assembly made MLCCs a standard component in electronic manufacturing. Subsequent development has emphasized thinner dielectric layers, finer powders, greater layer counts, base-metal electrodes, and improved resistance to mechanical stress. These advances increase capacitance density, but they also make effective capacitance, dielectric reliability, and manufacturing control central considerations in component performance.