Desalination is the removal of dissolved salts from saline water to produce water suitable for drinking, industrial processes, or agriculture. Its principal feedstocks are seawater and brackish surface water or groundwater, although related processes also treat saline industrial effluents. Unlike conventional filtration, which mainly removes suspended particles, desalination separates water from dissolved ions. It produces both a lower-salinity product and a concentrated residual stream, generally called brine.
Desalination provides a freshwater source that depends less directly on local rainfall than rivers, reservoirs, and shallow wells. It is especially important in arid coastal regions, islands, and cities with limited freshwater catchments. Its practical value nevertheless depends on reliable energy supplies, intake and discharge conditions, financing, and connections to water distribution systems. Modern plants predominantly use reverse osmosis, while thermal distillation remains important, particularly in parts of the Middle East. The design of a desalination system involves not only salt separation but also pretreatment, energy recovery, product-water stabilization, and management of environmental effects.
Feedwater, salt separation, and physical limits
The difficulty of desalination depends strongly on the composition of the feedwater. Open-ocean seawater typically contains about 35 grams of dissolved salts per kilogram of solution, although regional values vary. The Baltic Sea is substantially less saline, while restricted basins with strong evaporation, including the Red Sea and parts of the Persian Gulf, can be considerably saltier. Brackish water occupies an intermediate range between freshwater and seawater; operational definitions vary, but concentrations of roughly 1–10 grams of dissolved solids per liter are common in engineering usage. Sodium and chloride dominate seawater chemistry, but magnesium, sulfate, calcium, potassium, and bicarbonate also influence treatment.
Removing salt requires work because mixing water and salts is thermodynamically favorable. Osmosis is the movement of water through a selectively permeable membrane toward the solution with the greater osmotic pressure. In reverse osmosis, applied hydraulic pressure overcomes this tendency. For a dilute ideal solution, osmotic pressure is approximated by
where represents the effective number of dissolved particles per formula unit, is molar concentration, is the gas constant, and is absolute temperature. Concentrated seawater requires more accurate descriptions of ionic interactions. Typical seawater has an osmotic pressure of approximately 25–30 bar near room temperature.
Plant performance is commonly described by recovery and salt rejection. Recovery is the fraction of feedwater converted into product water:
where and are product and feed flow rates. Salt rejection is often expressed as , with and denoting product and feed salt concentrations. These measures describe different properties: a membrane may reject nearly all incoming salt while the system converts less than half its feed into freshwater.
A mass balance connects freshwater production to brine generation. Neglecting the small amount of salt in the product and approximating densities as equal,
At 50 percent recovery, the brine therefore contains approximately twice the feed salt concentration. Increasing recovery reduces the intake and discharge volumes per unit of product, but raises brine salinity, required pressure, and the risk of mineral precipitation.
Thermodynamics places a lower bound on energy consumption. For seawater containing about 35 grams of salt per kilogram at approximately 25 °C, the reversible minimum is roughly 0.8 kilowatt-hours per cubic meter of product at very low recovery and around 1.1 kilowatt-hours per cubic meter at 50 percent recovery. Actual plants consume more because pumps, membranes, piping, and energy-recovery devices are imperfect. These limits also explain why performance claims must specify feed salinity, recovery, product quality, and the equipment included in the energy calculation.
Historical development and geographical adoption
The principle of obtaining freshwater by evaporating saline water and condensing the vapor has been known since antiquity. Aristotle discussed the separation of freshwater from seawater through evaporation. For centuries, however, the energy and equipment required restricted practical use. Distillation became particularly valuable aboard ships, where access to freshwater could determine voyage endurance. The expansion of steam navigation in the nineteenth century encouraged improved evaporators and condensers, although boiler-water treatment and drinking-water production presented different operational requirements.
Large-scale development accelerated after World War II. Growing populations, expanding industry, and oil revenues supported investment in water infrastructure across the Arabian Peninsula. Kuwait developed large seawater-distillation installations during the 1950s, helping establish the model of coastal plants supplying cities with few nearby freshwater resources. Multi-stage flash distillation subsequently became a major municipal supply technology. Its deployment was closely associated with power stations, which could supply steam and electricity to adjacent desalination equipment.
Membrane desalination developed along a different technological path. In 1960, Sidney Loeb and Srinivasa Sourirajan demonstrated practical asymmetric cellulose acetate membranes with a thin selective surface and a more permeable supporting structure. Their work addressed the problem of obtaining useful water flow while retaining dissolved salts. Commercial reverse-osmosis applications expanded during the 1960s and 1970s, initially with particular advantages for brackish water. Later thin-film composite polyamide membranes, better high-pressure pumps, and improved energy recovery made seawater reverse osmosis increasingly competitive.
By the early twenty-first century, reverse osmosis had become the dominant technology for new desalination capacity. Large installations were built not only in the Gulf region but also around the Mediterranean, in Australia, in East Asia, and along parts of the American coastline. Israel’s Sorek plant, commissioned in 2013, was designed to produce approximately 150 million cubic meters annually. The Claude “Bud” Lewis Carlsbad Desalination Plant in California began commercial operation in 2015, with a nominal capacity of about 50 million US gallons per day, approximately 189,000 cubic meters.
Different regions adopted desalination for different reasons. Gulf states use it as a central component of municipal supply. Singapore incorporates it into a diversified system alongside imported water, local catchments, and reclaimed water. Australian coastal cities expanded desalination after prolonged drought, often retaining plants as insurance even when rainfall subsequently improved. Spain combines substantial seawater desalination with applications in islands, tourism, and agriculture.
Installed capacity is not the same as actual annual production. A plant may operate continuously, seasonally, or mainly during drought, and its practical contribution depends on maintenance, electricity availability, storage, and distribution. Desalination therefore ranges from a foundational source of urban water to a reserve asset within a broader water-supply portfolio.
Reverse osmosis and other membrane processes
A reverse-osmosis membrane allows water to pass much more readily than dissolved salts. Most modern desalination membranes contain a very thin polyamide selective layer supported by porous layers that provide mechanical strength. The selective layer is not simply a sieve with uniform holes smaller than salt ions. Water and dissolved substances interact differently with the membrane material, and transport depends on their uptake and movement through its structure. Membrane chemistry, cross-linking, surface charge, and operating conditions all affect permeability and selectivity.
In commercial systems, membrane sheets are commonly assembled into spiral-wound elements. Feedwater passes along narrow channels between membrane leaves. Water permeating through the membrane enters a spacer-supported collection channel and flows toward a central product tube. Several elements are placed in a pressure vessel, and many vessels operate in parallel. As feedwater travels through an array, its volume decreases and its salinity rises. This changing composition influences the required pressure, local flux, and scaling risk along the system.
Seawater reverse-osmosis systems commonly operate at approximately 55–80 bar, with higher pressures possible for unusually saline feeds or demanding recovery conditions. Brackish-water systems often operate at roughly 10–25 bar. Typical seawater recovery is around 35–50 percent, while brackish-water recovery can often reach 70–85 percent where feed chemistry permits. These are representative ranges rather than fixed limits. Temperature, membrane age, product specifications, and the concentration of sparingly soluble salts can shift the operating point.
A simplified expression for water flux is
where is membrane water permeability, is the hydraulic pressure difference, and is the osmotic pressure difference. Actual design must also account for concentration polarization: salt accumulates near the membrane surface because water crosses the membrane while most salt does not. This makes the local osmotic pressure greater than the value inferred from the bulk feed. Feed-channel mixing and adequate crossflow help limit the effect, but also increase hydraulic losses.
Other membrane technologies serve different feedwaters and objectives. Electrodialysis moves dissolved ions through alternating cation- and anion-selective membranes under an electric field. Because its energy requirement is closely related to the amount of salt transported, it is particularly useful for some brackish-water applications. Electrodialysis reversal periodically changes electrical polarity to reduce certain forms of scaling and fouling.
Nanofiltration preferentially removes many multivalent ions and organic compounds, but usually does not provide adequate monovalent-salt rejection for direct seawater-to-drinking-water treatment. It can instead soften feedwater or support more complex treatment trains. Forward osmosis uses a concentrated draw solution to attract water across a membrane; producing usable freshwater then requires separating water from that solution. Its apparent lack of a high-pressure membrane stage does not eliminate the energy requirement of the overall separation.
Thermal distillation and heat-driven systems
Thermal desalination separates water from salts by evaporation and condensation. Most dissolved inorganic salts are effectively nonvolatile under normal operating conditions, so the condensed vapor has very low salinity. The central engineering challenge is not whether evaporation can separate water, but how often the supplied heat can be reused. Evaporating one kilogram of water requires roughly 2.3 megajoules of latent heat near ordinary desalination temperatures. Single-use evaporation would consequently consume far more energy than modern large-scale systems can economically tolerate.
Multi-stage flash distillation, usually abbreviated MSF, sends heated seawater through a sequence of chambers maintained at progressively lower pressures. In each chamber, some water rapidly vaporizes because the incoming liquid is warmer than the local boiling temperature. The vapor condenses on tubes carrying colder incoming seawater, transferring heat back into the process. Many plants recirculate part of the brine, with makeup water and a blowdown stream maintaining the salt balance. Top brine temperatures have commonly been around 90–110 °C, although specific designs vary.
Multiple-effect distillation, or MED, also reuses latent heat, but organizes evaporation into successive effects. Vapor generated in one effect condenses on a heat-transfer surface and supplies the heat that evaporates water in the next effect, operating at lower pressure and temperature. Seawater may be sprayed over horizontal tubes to form thin films. Many modern MED systems operate with top temperatures around 60–70 °C, helping reduce scaling and allowing the use of relatively low-temperature heat sources.
Vapor-compression distillation increases the temperature and pressure of generated vapor so that it can condense at a temperature high enough to drive further evaporation. Mechanical vapor compression uses a compressor powered by electricity. Thermal vapor compression uses a steam ejector to entrain and compress lower-pressure vapor. The appropriate arrangement depends on plant size, available steam, electricity cost, and operating requirements. Compact mechanical systems are useful in some industrial and smaller-scale applications.
Thermal performance is often expressed by the gained output ratio: the mass of distillate produced per unit mass of externally supplied heating steam. A higher ratio generally indicates more effective heat reuse, but additional effects, stages, and heat-transfer area increase capital cost. Indicative heat inputs for established large thermal processes are often about 40–120 kilowatt-hours of thermal energy per cubic meter, alongside auxiliary electricity. This range spans different technologies and operating conditions rather than representing a universal specification.
Heat and electricity cannot be compared simply by adding their numerical energy quantities. Low-temperature heat has less capacity to perform useful work than the same quantity of electrical energy. Combined heat and power arrangements can therefore make thermal desalination attractive where suitable steam is available. Nevertheless, extracting steam may reduce electricity production, so it is not automatically costless “waste heat.”
Thermal plants also face corrosion, scaling, and vapor carryover. Droplet separators prevent saline droplets from contaminating the distillate, while careful materials selection and chemical control protect heat exchangers. These requirements distinguish a reliable industrial distillation plant from a simple evaporating vessel.
Intakes, pretreatment, and finished-water production
A desalination plant is a complete treatment system rather than an isolated membrane rack or evaporator. Its intake determines the quality and variability of the water entering the process. Open seawater intakes can supply large flows but may admit suspended sediment, plankton, algae, and debris. Subsurface intakes, including beach wells and infiltration galleries, allow seawater to pass through sediments before collection. They can provide naturally filtered water, although their feasibility depends on coastal geology, permeability, available shoreline, and the flow required.
Pretreatment protects downstream equipment from fouling and damage. Screens remove large debris, while coagulation and filtration can remove fine particles and organic matter. Dissolved-air flotation is particularly useful for some low-density particles and algal cells. Granular-media filters, ultrafiltration, or combinations of these processes may be used before reverse osmosis. Cartridge filters commonly provide a final protective barrier. Pretreatment design depends on seasonal conditions, storms, dredging, harmful algal blooms, and nearby pollution sources rather than feed salinity alone.
Membrane fouling has several distinct mechanisms. Colloids and particles accumulate on surfaces or in feed spacers; microorganisms form biofilms; organic compounds adsorb to the membrane; and sparingly soluble minerals precipitate as scale. Calcium carbonate, calcium sulfate, barium sulfate, and silica can constrain operation under different feed conditions. Antiscalants interfere with crystal formation and growth, while acid addition can reduce carbonate-scaling potential. These measures allow higher concentration factors within chemical and operational limits.
Disinfection requires particular care in polyamide reverse-osmosis plants. Chlorine can help control biological growth upstream, but most conventional polyamide membranes are vulnerable to oxidative damage. Residual chlorine is therefore commonly removed before the membrane stage, often with a reducing agent such as sodium bisulfite. This creates an operational tension: protecting the membrane from oxidants also removes a disinfectant residual from equipment susceptible to biological fouling. Cleaning procedures must be matched to the foulant and the membrane’s allowable chemical exposure.
Desalinated water usually requires stabilization before entering distribution. Very low mineral content and alkalinity can make untreated product water corrosive to pipes and fixtures. Remineralization may use limestone contactors, lime and carbon dioxide, or blending with another suitable water source. The aim is to establish appropriate calcium content, alkalinity, and pH, followed by disinfection suitable for the distribution network. Thermal distillate generally requires similar attention despite its very low salt content.
Specific contaminants can require additional treatment. Boron occurs largely as uncharged boric acid at normal seawater pH and is less strongly rejected than many ions. A second reverse-osmosis pass, sometimes operated at higher pH, can improve boron removal. Industrial users may require further demineralization, while agricultural users must consider sodium, chloride, boron, and nutrient balance. Compliance with drinking-water requirements is therefore assessed on the finished water, not inferred solely from the salt rejection of a membrane or the purity of newly condensed vapor.
Energy use, recovery, and integration with power supplies
Energy consumption is a central operating cost and environmental consideration in desalination. Modern large seawater reverse-osmosis plants commonly consume roughly 3–5 kilowatt-hours of electricity per cubic meter of finished water when intake, pretreatment, high-pressure pumping, and other plant loads are included. Favorable installations may achieve lower values, while high salinity, stringent product requirements, small scale, or difficult intake conditions can raise consumption. Pumping water inland or uphill adds further demand and is often reported separately.
A major efficiency improvement has been recovery of pressure energy from the concentrated brine. Water leaving a reverse-osmosis membrane array retains much of its feed pressure. Earlier systems used turbines or hydraulic devices to transfer some of this energy back to the pump shaft. Modern isobaric pressure exchangers transfer pressure more directly from the outgoing brine to incoming feedwater, greatly reducing the amount of high-pressure pumping required. Mixing, leakage, pressure losses, and auxiliary pumping still impose penalties, but energy recovery has been crucial to lowering seawater reverse-osmosis consumption.
Increasing membrane permeability alone cannot remove all energy demand. At a given salinity and recovery, the process must still overcome osmotic pressure. Higher permeability can reduce the extra pressure needed to sustain a chosen flux, or reduce membrane area, but may produce diminishing energy savings as the system approaches thermodynamic constraints. Excessive flux can also worsen concentration polarization and fouling. Efficient design therefore balances membrane properties, recovery, pressure losses, equipment cost, and cleaning requirements.
The carbon intensity of desalinated water depends on the energy supply. If a plant uses 4 kilowatt-hours per cubic meter and its electricity has an emissions intensity of 0.4 kilograms of carbon-dioxide equivalent per kilowatt-hour, operational electricity emissions are approximately 1.6 kilograms of carbon-dioxide equivalent per cubic meter. This illustrative calculation excludes construction, chemicals, membrane manufacture, and other life-cycle contributions. Thermal desalination requires additional accounting choices when steam and electricity are produced together.
Renewable energy can supply desalination through grid-connected electricity or dedicated generation. Solar and wind power can reduce fossil-fuel use, but their variability has operational consequences. Frequent starts, shutdowns, and pressure changes may affect treatment stability and equipment operation. Product-water storage can sometimes shift production more economically than storing the corresponding energy in a battery, although the appropriate balance depends on electricity prices, storage capacity, and required water-supply reliability.
Heat-driven desalination can also use solar thermal energy, geothermal resources, or heat associated with nuclear power and industrial processes. The availability, temperature, continuity, and opportunity cost of that heat determine whether integration is practical. Simple solar stills use sunlight to evaporate and condense water within an enclosure, but their low output per unit area generally limits them to small applications. Large-scale solar-powered desalination usually relies instead on electricity generation or engineered thermal cycles with substantially greater equipment complexity.
Costs, infrastructure, and allocation of water
The cost of desalinated water includes financing and constructing the plant, replacing equipment, buying energy and chemicals, paying operators, maintaining facilities, and managing residuals. A complete delivered-water cost also includes transmission pipelines, pumping stations, storage reservoirs, and distribution connections. Published prices are consequently difficult to compare unless their boundaries are clear. A low bulk-water contract price at a coastal plant does not necessarily represent the cost paid by consumers far inland.
Scale can reduce unit costs by spreading design, construction, staffing, and procurement expenses across greater output. Favorable large seawater reverse-osmosis projects can produce water at plant-gate costs below US$1 per cubic meter, while small, remote, highly saline, or difficult projects may cost substantially more. Electricity prices, interest rates, exchange rates, local construction conditions, and plant utilization can be as important as membrane performance. Tender prices may also reflect contractual assumptions about power supply, land, financing, and long-term purchase commitments.
High utilization spreads fixed costs over more cubic meters. A drought-reserve plant that operates infrequently may therefore have a higher average cost per cubic meter actually produced than a continuously operated plant, even if its equipment performs efficiently. Such a facility also provides a service not fully captured by production cost: the ability to supply water when reservoirs are depleted. Decisions about this reserve function connect desalination to infrastructure planning, demand forecasting, and the economic consequences of supply failure.
Desalination competes with and complements other water-management measures. Leakage reduction, demand management, reservoir expansion, interbasin transfers, groundwater development, and water reuse all have different costs and constraints. Wastewater treatment followed by advanced purification can produce an alternative water source whose feed salinity is often much lower than seawater. However, reuse depends on wastewater availability, collection systems, treatment requirements, and the intended application. No single ranking applies to every city or region.
Geography strongly affects the value of seawater desalination. Coastal populations can receive product water through relatively short connections, whereas inland cities may require expensive pipelines and substantial pumping energy. Brackish-water desalination can be located nearer inland demand, but extraction must be evaluated against aquifer recharge, water rights, and the difficulty of disposing of concentrate away from the sea. A technically productive well does not necessarily provide a renewable supply.
Agricultural use is especially sensitive to cost because many crops generate relatively little revenue per unit of water consumed. Desalinated water is more feasible for high-value crops, greenhouses, or blending than for unrestricted irrigation of low-value field crops. Irrigation applications also require attention to calcium, magnesium, boron, and sodium balance rather than simply minimizing total dissolved solids. Industrial users may place a higher value on consistent composition and supply reliability, particularly when interruptions would halt production or damage equipment.
Environmental effects, regulation, and research priorities
Environmental effects begin at the intake. Screens can trap larger organisms, while smaller organisms, eggs, and larvae may pass into the treatment system. These processes, termed impingement and entrainment, depend on intake design, water velocity, location, seasonal biology, and the volumes withdrawn. Subsurface intakes can reduce direct uptake of marine organisms, but their construction and operation introduce different geological, coastal, and land-use constraints. Site-specific ecological assessment is therefore more informative than a single universal intake preference.
Concentrate discharge is another major concern. Reverse-osmosis brine is denser than surrounding seawater and may spread along the seabed if mixing is weak. Thermal-plant discharges may also be warmer than ambient water. Elevated salinity, temperature changes, residual treatment chemicals, and cleaning wastes can affect organisms, particularly in shallow or poorly flushed environments. The outcome depends on dilution and exposure as well as the sensitivity of nearby habitats, including seagrass beds, coral communities, and other benthic ecosystems.
Outfalls commonly use multiport diffusers to increase mixing. Some plants combine brine with other discharge streams, although this changes rather than removes the need to assess environmental effects. Near-field plume models describe initial jet mixing, while larger-scale hydrodynamic models examine transport under tides, currents, and seasonal stratification. Monitoring can include salinity, temperature, dissolved oxygen, chemical residuals, and biological indicators. Compliance requirements are generally set through local permits and environmental assessment rather than a globally uniform discharge standard.
Inland concentrate disposal is often more difficult than marine discharge. Options include permitted sewer discharge, evaporation ponds, deep-well injection where geological and regulatory conditions allow, and further concentration. Zero-liquid-discharge systems recover additional water and leave salts or other solids, frequently through combinations of membrane concentration, evaporation, and crystallization. They can reduce liquid disposal requirements but generally increase energy consumption, capital cost, and the need to manage solid residues.
Research seeks improvements in membrane selectivity, fouling resistance, pretreatment, energy recovery, and concentrate management. Membrane distillation transfers water vapor through a hydrophobic porous membrane under a vapor-pressure difference and can use low-temperature heat. Its development must address membrane wetting, heat losses, scaling, and long-term operation. Capacitive deionization stores ions electrostatically or through related electrode processes and is generally better suited to lower-salinity streams than ordinary seawater. New materials must demonstrate stable performance with realistic feedwaters, not merely high flux under laboratory conditions.
Recovering valuable substances from brine is another active area, but feasibility depends on concentration, separation selectivity, purification cost, and market size. Sodium chloride and magnesium compounds have established industrial markets, yet a desalination brine is not automatically a profitable mineral resource. Trace constituents may require treating very large volumes to recover small quantities. Integrating resource recovery with freshwater production therefore requires a full chemical and economic balance, including the residual waste streams created by the recovery process.