Static friction is a form of friction that acts between contacting surfaces when they are not sliding relative to one another. It is a tangential force that opposes the tendency for relative sliding, rather than necessarily opposing an object’s motion. Its magnitude adjusts to the forces and constraints acting on the bodies, up to a limiting value. Static friction allows people to walk without slipping, enables tires to transmit driving and braking forces, and helps fastened components remain in place.
Definition and direction
The distinction between static and sliding friction concerns motion at the contact, not whether an entire object is stationary. A box resting on a floor may experience static friction when pushed horizontally. A wheel rolling without slipping can also experience static friction even though its center is moving.
Static friction acts parallel to the contact surface. Its direction is the direction needed to prevent the surfaces from sliding relative to each other. Depending on the situation, it may point forward, backward, uphill, or downhill. If there is no tendency to slide and no tangential force is needed to maintain the contact constraint, static friction can be zero.
The friction forces that two contacting bodies exert on each other are equal in magnitude and opposite in direction, in accordance with Newton’s third law. The normal force, by contrast, acts perpendicular to the contact surface.
The limiting-friction model
In the commonly used dry-friction model, the magnitude of static friction satisfies
where is the static-friction force, is the normal load, and is the coefficient of static friction.
The coefficient is dimensionless. It characterizes a pair of surfaces under specified conditions, rather than being an intrinsic property of one material alone. Surface preparation, contamination, humidity, temperature, contact history, and the duration of contact can all affect its measured value. It need not be less than one.
The equation
applies only at the limiting condition, often called impending slip. Below that limit, the force must be found from the equations of motion and the requirement of no relative sliding.
For example, consider a block on a horizontal floor subjected to a horizontal applied force , with no other horizontal forces. As long as the block remains at rest,
Increasing increases the friction force until the limiting value is reached. If the required friction exceeds that limit, the block cannot remain at rest under this model.
During sliding, kinetic friction replaces the static-friction description. For many dry material pairs, the force required to initiate sliding exceeds the force required to maintain sliding at a modest speed. This is common but not universal.
Microscopic origin
Nominally smooth solid surfaces are usually rough on microscopic scales. They touch at a population of small high points, called asperities, rather than across their entire apparent contact area.
Under load, these contacts deform elastically or plastically. Resistance to tangential displacement arises from several interacting mechanisms:
- Adhesive junctions: atomic and molecular interactions bind contacting regions, which resist shearing.
- Asperity deformation and interlocking: surface features deform or obstruct relative movement.
- Surface films: oxides, adsorbed molecules, contaminants, and lubricants alter junction strength and deformation.
Interactions such as van der Waals forces and, in some contacts, chemical bonding contribute to adhesion. Static friction is therefore not explained solely by roughness or by geometrical interlocking.
A simplified account of the approximate proportionality between limiting friction and normal load is that increasing the load increases the real contact area. If the average shear strength of the junctions remains roughly constant, the force needed to shear them also increases.
The familiar approximation that dry friction is independent of apparent contact area has limits. Soft materials, strongly adhesive surfaces, very small contacts, and contacts under extreme pressure can behave differently. These effects are studied in tribology, the science and engineering of interacting surfaces in relative motion.
Representative mechanical situations
A block on an inclined plane
For a block of mass resting on a plane inclined at an angle above the horizontal, gravity produces a downslope component . If there are no other applied forces,
Static friction acts upslope and has magnitude
The condition for remaining at rest is
or
At the limiting angle ,
This relation provides a simple measurement method, provided the object slides rather than tips or rolls and the assumed friction model is appropriate.
Walking and tire traction
During walking, a planted foot can push backward on the ground while the ground exerts a forward static-friction force on the foot. The force may reverse direction during other phases of a step.
A driven tire similarly pushes backward against the road, and the road supplies a forward force that helps accelerate the vehicle. During braking, the longitudinal road force generally acts backward. When a vehicle turns without skidding, lateral tire forces supply the acceleration required to change direction.
Real tires are deformable, and their contact patches can contain both adhering and locally slipping regions. Describing traction simply as static friction is therefore an approximation.
Rolling without slipping
For a wheel of radius rolling on a stationary flat surface without slipping,
where is its center-of-mass speed and is its angular speed.
Static friction can provide a torque that maintains this rolling condition. It is not always required: an ideal rigid wheel rolling uniformly on a level surface, with no other horizontal forces or resistive torques, can have zero friction force. Rolling resistance caused by deformation is distinct from the static-friction constraint.
Work and energy
Static friction does not invariably do zero work. Its work depends on the displacement of the point where the force acts.
For an ideal rigid wheel rolling without slipping on a stationary rigid surface, the instantaneous point of contact is at rest in the ground frame. The static-friction force therefore has zero instantaneous power at that contact, even though it can change the wheel’s translational and rotational motion.
By contrast, static friction can do positive work on an object carried by a moving belt without slipping. The object’s contact point moves in the laboratory frame, so friction can transfer energy from the belt to the object.
In an ideal sticking contact, the opposing friction forces do not dissipate energy through relative sliding because the relative contact velocity is zero. Real contacts can nevertheless lose mechanical energy through local microslip, deformation, and other processes, producing heat.
Measurement and limitations
Static friction is commonly measured by increasing a tangential force until sliding begins, or by gradually tilting an inclined plane. In a horizontal pull test,
provided the measured onset force represents the limiting friction and the pulling arrangement does not introduce unaccounted changes in normal load or cause tipping.
The measured threshold depends on the test procedure. Loading rate, vibration, alignment, surface wear, and the time spent at rest can affect the result and its measurement uncertainty. In many contacts, frictional strength grows with the time spent stationary, an effect called contact aging.
The simple limiting-friction law is an empirical approximation, not a complete microscopic theory. Before gross sliding begins, a contact may undergo small tangential deformation and localized slip. The transition to sliding may involve propagating slip fronts rather than simultaneous failure across the entire interface.
Repeated alternation between sticking and sliding produces stick–slip motion, which can cause vibration, noise, and irregular movement in mechanical systems. More detailed friction models include dependence on sliding speed, contact state, and loading history; such models are also used in studies of geological faults.