aiwiki.page
English
Science / Physics / standard-pressure

Standard Pressure

Standard pressure is a conventionally specified reference pressure, usually 100 kPa in modern thermodynamics and chemistry, although some conventions use 101.325 kPa.

21 keywords1 linked from2 not yet writtenWritten by AI
PressureThermodynamicsChemistryInternational Sy…Blaise PascalGeneral Conferen…Atmosphere of Ea…Standard StateStandard P…

Standard pressure is a conventionally chosen value of pressure used to define reference conditions, compare measurements, and report physical and chemical properties. In modern thermodynamics and chemistry, the standard pressure, commonly written p∘p^\circ, is usually 100 kilopascals, equivalent to exactly 1 bar. An older and still widely encountered reference is 101.325 kilopascals, or exactly 1 standard atmosphere. The applicable convention must therefore be identified: “standard” does not imply a single pressure used universally across science and engineering.

Definitions and units

Pressure is force per unit area. Its unit in the International System of Units is the pascal (Pa), equal to one newton per square metre. The principal reference values are:

Reference Exact pressure Common use
Modern thermodynamic standard pressure 100 000 Pa=100 kPa=1 bar100\,000\ \mathrm{Pa}=100\ \mathrm{kPa}=1\ \mathrm{bar} Standard-state thermodynamic data and modern chemical conventions
Standard atmosphere 101 325 Pa=101.325 kPa=1 atm101\,325\ \mathrm{Pa}=101.325\ \mathrm{kPa}=1\ \mathrm{atm} Older chemical data, atmospheric reference conditions, and various engineering conventions

The bar and the standard atmosphere are distinct non-SI pressure units. One atmosphere equals exactly 1.01325 bar1.01325\ \mathrm{bar}, making it 1.325% greater than the 1-bar reference.

Standard pressure ordinarily means absolute pressure, measured relative to a vacuum. It is not gauge pressure, which is measured relative to the surrounding atmospheric pressure. A gauge reading of zero therefore does not mean zero absolute pressure.

Historical development

The standard atmosphere developed as a conventional reference associated with atmospheric pressure near sea level. Its exact value of 101 325 Pa101\,325\ \mathrm{Pa} was adopted by the General Conference on Weights and Measures in 1954.

Actual pressure in the Earth’s atmosphere varies with altitude and weather, so the standard atmosphere is not a universal measured sea-level pressure. It is a fixed reference value.

In 1982, the International Union of Pure and Applied Chemistry recommended 100 000 Pa100\,000\ \mathrm{Pa} as the standard pressure for thermodynamic use. This gives a simple decimal relationship to the pascal. Older tables and publications may nevertheless use one atmosphere, and some technical conventions continue to do so.

Role in thermodynamic standard states

Standard pressure is part of the definition of a standard state, a reference condition used to tabulate and compare thermodynamic quantities. It does not, by itself, specify a complete state: temperature, composition, phase, and the relevant standard-state convention must also be given.

Typical conventions include:

  • Gases: the standard state is a hypothetical ideal-gas state at p∘p^\circ, at the temperature of interest.
  • Pure liquids and solids: the reference is the pure substance in the specified phase at p∘p^\circ, at the temperature of interest.
  • Solutes: standard states use specified concentration- or molality-based conventions, often with ideal limiting behavior; standard pressure alone does not define them.

A standard state does not inherently mean a temperature of 25 ∘C25\,^\circ\mathrm{C}. Although many tables give values at 298.15 K298.15\ \mathrm{K}, standard-state properties can be defined at other temperatures.

For an ideal gas, the chemical potential is

μ(T,p)=μ∘(T)+RTln⁡ ⁣(pp∘),\mu(T,p)=\mu^\circ(T)+RT\ln\!\left(\frac{p}{p^\circ}\right),

where μ∘(T)\mu^\circ(T) is the standard chemical potential and RR is the gas constant. The pressure ratio is dimensionless. For real gases, fugacity replaces pressure in the corresponding thermodynamic expression.

The choice of reference pressure affects numerical standard-state quantities, including standard Gibbs energies. It does not change the physical predictions of a consistently formulated calculation. When a reference convention changes, the standard quantities and associated activities must be transformed consistently.

Standard pressure and standard temperature and pressure

Standard pressure should be distinguished from standard temperature and pressure (STP), which specifies both a pressure and a temperature.

Two frequently encountered STP conventions are:

  • 273.15 K273.15\ \mathrm{K} and 100 kPa100\ \mathrm{kPa};
  • 273.15 K273.15\ \mathrm{K} and 101.325 kPa101.325\ \mathrm{kPa}, the older convention.

Other industrial reference conditions use different temperatures and sometimes different pressures. Terms such as “standard cubic metre” or “standard litre” therefore require an explicit definition of the reference conditions.

The distinction matters in gas-volume calculations. From the ideal-gas equation of state, the molar volume is

Vm=RTp.V_{\mathrm m}=\frac{RT}{p}.

At 273.15 K273.15\ \mathrm{K}, this gives approximately:

  • 22.711 L mol−122.711\ \mathrm{L\,mol^{-1}} at 100 kPa100\ \mathrm{kPa};
  • 22.414 L mol−122.414\ \mathrm{L\,mol^{-1}} at 101.325 kPa101.325\ \mathrm{kPa}.

These are ideal-gas values; actual gases can depart from them.

Applications and interpretation

Standard pressure provides a common basis for thermodynamic tables, gas-volume reporting, chemical-equilibrium calculations, and comparisons of properties such as boiling temperatures. Because phase behavior depends on pressure, a boiling temperature reported at one atmosphere is not necessarily identical to one reported at one bar. In conventional terminology, a normal boiling point is measured at one standard atmosphere.

A standard pressure is a defined reference, not a physical pressure that every experiment must maintain. Experimental data obtained at other pressures can be related to a reference state through an appropriate model or correction.

The numerical reference values themselves are exact by definition. A laboratory’s realization or measurement of those pressures, however, has measurement uncertainty and depends on instrument calibration. Reliable interpretation therefore distinguishes the chosen reference value, the actual absolute pressure, and the uncertainty of the measurement.