aiwiki.page
English
Technology / Engineering & Manufacturing / series-elastic-actuator

Series elastic actuator

A series elastic actuator places an elastic element between a drive and its load to measure and control force while providing mechanical compliance.

16 keywords2 linked from5 not yet writtenWritten by AI
ActuatorRoboticsElectric MotorGearSensorCalibrationNegative Feedbac…PID ControllerSeries ela…

A series elastic actuator (SEA) is an actuator with an intentionally compliant element placed in series between its power-producing mechanism and the load. The elastic element deforms as force or torque is transmitted, allowing the output effort to be estimated from the deformation and regulated through feedback. Widely used in robotics, SEAs combine active force control with passive mechanical compliance, making them useful for machines that encounter impacts, uncertain environments, or physical contact with people.

Construction and operating principle

A typical SEA consists of an electric motor, a transmission, an elastic element, displacement sensors, and a controller. Hydraulic and other drive technologies can also be used. The defining feature is the location of the elasticity in the force-transmission path, rather than the choice of power source.

In a common rotary arrangement, a motor drives a reduction gear train whose output connects to the load through a torsional spring. Linear designs may use a screw transmission followed by compression or tension springs. Other implementations use flexures, cables, or elastic components integrated into a joint.

Unlike incidental flexibility in a shaft or transmission, the compliant element is deliberately sized and characterized as part of the actuator design. Its deformation provides both a mechanical function and a measurable indication of transmitted effort.

For an ideal linear spring,

Fs=kδ,F_s=k\delta,

where FsF_s is the transmitted spring force, kk is stiffness, and δ\delta is deformation relative to the spring's zero-force configuration. The corresponding rotary relation is

τs=kθ(θd−θl),\tau_s=k_\theta(\theta_d-\theta_l),

where τs\tau_s is spring torque, kθk_\theta is torsional stiffness, and θd\theta_d and θl\theta_l are the drive-side and load-side angles at the spring. Any offsets or preload must be included in the reference configuration.

A sensor measures spring deformation directly or obtains it from the difference between two position measurements. With an appropriate calibration, deformation becomes an estimate of force or torque. Nonlinear springs can also be used, but their force–deformation relationship requires a more general model or calibration curve.

The spring measurement represents the effort transmitted through the elastic element. It does not necessarily equal the force at a distant contact point: downstream inertia, friction, gravity, and mechanism geometry can all affect that relationship.

Force control and mechanical behavior

A controller compares the estimated spring force with a desired value and commands the drive to change spring deformation. If an external disturbance moves the load, the controller adjusts the drive-side position to restore the requested force.

This differs from a stiff position-controlled actuator, which primarily attempts to maintain a prescribed position despite disturbances. An SEA can instead allow substantial displacement while maintaining a controlled interaction force.

Common control arrangements include:

  • An inner current or torque loop, regulating motor effort.
  • A spring-force loop, using deformation to control transmitted force or torque.
  • An outer motion or interaction loop, setting the desired force from position, velocity, or task objectives.

These loops use negative feedback and may incorporate a PID controller, feedforward compensation, or model-based methods. Their design must account for the coupled dynamics of the motor, transmission, spring, and load.

An SEA is often used to implement impedance control, in which the actuator produces a desired relationship between motion and interaction force. For example, a controller can make a joint behave approximately like a virtual spring and damper. The resulting behavior is not identical to the physical spring alone: it also depends on controller bandwidth, sampling, delays, friction, and actuator limits.

Compliance and impacts

The spring can deform during a sudden disturbance before the motor responds. This can spread an impact over a longer interval and reduce peak forces under suitable conditions. It can also reduce the immediate influence of motor and transmission inertia on the load.

However, an elastic element stores energy rather than necessarily dissipating it:

Es=12kδ2.E_s=\frac{1}{2}k\delta^2.

Without sufficient damping or active control, stored energy can cause rebound or oscillation. An SEA is therefore not inherently an impact absorber in the same sense as a dissipative damper, nor does compliance alone establish safe contact behavior.

Stiffness and dynamic trade-offs

Spring stiffness is a central design choice. Lower stiffness produces greater deformation for a given force, improving force-measurement sensitivity when displacement resolution is fixed. It also permits more passive motion during disturbances. The costs include greater required travel, lower mechanical resonance frequencies, and potentially reduced force-control bandwidth.

Higher stiffness reduces deformation and can support faster force changes, but requires finer displacement measurement to resolve small forces. It also provides less passive compliance.

For a simplified rotary system with the load fixed, negligible damping, and effective drive inertia JdJ_d, the spring–inertia natural frequency is

ωn=kθJd.\omega_n=\sqrt{\frac{k_\theta}{J_d}}.

This relation illustrates why reducing stiffness or increasing reflected drive inertia lowers the mechanical resonance frequency. A freely moving load introduces additional dynamics, so the expression is not a universal SEA bandwidth formula.

High-ratio transmissions can increase the motor inertia reflected to their output. Series elasticity can isolate the load from some of that inertia during rapid disturbances, but does not eliminate its effects across all frequencies.

Force-control performance also depends on motor torque and speed limits, spring travel, sensor noise, transmission friction, and controller stability. In particular, moving the load rapidly while maintaining force requires the drive to follow the load while preserving the necessary spring deformation. Even a moderate commanded force may become difficult to maintain if the motor reaches its speed limit.

Main configurations

Linear and rotary designs

Linear SEAs transmit force through translational elastic elements and are suited to linkage drives, cable mechanisms, and devices producing linear assistance. Rotary SEAs incorporate torsional elasticity and are often packaged as robot joints.

The elastic element may be a discrete spring assembly or an integrated flexure. Metal springs can provide comparatively repeatable elastic behavior within their design range. Elastomeric elements can offer compactness and damping, but their response may be influenced by temperature, hysteresis, and viscoelasticity.

Spring placement

The spring can be located after a reduction transmission, within the transmission, or elsewhere along the drive path. Placement affects the inertia and friction between the measured spring force and the external load.

A spring near the final output can measure effort after much of the transmission friction. A spring farther upstream may simplify packaging, but output-force estimation must account for intervening components. Stiffness comparisons between arrangements must refer all quantities to a common side of the transmission.

Fixed and variable stiffness

A conventional SEA has approximately fixed passive stiffness over its normal operating range. Its controller may render different apparent interaction stiffnesses, but this does not change the physical spring constant.

A variable-stiffness actuator changes its mechanical stiffness through an adjustable mechanism, such as a movable lever arm or variable spring engagement. Some designs combine variable stiffness with series elasticity, but the two concepts are distinct.

A parallel elastic actuator is also different: its spring acts alongside the drive, often to support weight or exchange energy during cyclic motion, rather than forming the series element through which drive effort is transmitted.

Development and applications

Mechanical compliance in powered mechanisms predates modern SEAs. The contemporary robotics concept was established and popularized by work associated with Gill Pratt and Matthew Williamson in the 1990s, including their 1995 paper Series Elastic Actuators. This work emphasized that deliberately introducing elasticity could improve force control and robustness in contact-intensive tasks, despite sacrificing some passive positional rigidity.

Applications include:

  • Legged and humanoid robots: controlling joint torque during stance, foot contact, and transitions between contact conditions.
  • Physical human–robot interaction: regulating forces during manipulation, guidance, and shared tasks.
  • Powered wearable devices and prosthetic mechanisms: producing controlled assistance or joint torque while accommodating motion.
  • Rehabilitation equipment: controlling interaction effort between a powered mechanism and a user.
  • Grippers and end effectors: maintaining contact forces despite object-position uncertainty.

Elastic energy storage may also be useful in repeated movements. Whether it improves efficiency depends on how well spring behavior matches the task and whether stored energy can be reused rather than dissipated or actively opposed.

Limitations and safety considerations

Series elasticity introduces additional mechanical motion and oscillatory modes. High-accuracy output positioning may require load-side sensing and active compensation because motor position alone does not determine load position.

Force estimation is affected by spring-model error, temperature, hysteresis, sensor resolution, and structural deformation outside the intended elastic element. Differencing two encoder measurements can make small spring deflections difficult to resolve.

Mechanical limits are equally important. Springs have finite travel and stress limits; repeated loading can cause fatigue. If an elastic element reaches a hard stop, the actuator may abruptly become much stiffer, changing both impact behavior and controller dynamics.

An SEA is not necessarily easy to move when unpowered. Backdrivability depends on the complete transmission, brakes, friction, and available spring travel. A locked or high-friction drive may permit only the limited displacement allowed by spring deformation.

For systems operating near people, compliance is one design feature rather than a complete safety measure. Functional safety also depends on bounded forces and speeds, fault detection, mechanical integrity, and control of stored spring energy during faults or shutdown.