Reflectance is the ratio of reflected radiant power to incident radiant power. It describes how much electromagnetic radiation a surface or material returns rather than absorbs or transmits. Reflectance is dimensionless and is commonly expressed as a number between 0 and 1 or as a percentage. It is not generally a single fixed property of a material: it depends on wavelength, illumination direction, polarization, surface condition, and the directions over which reflected radiation is collected.
Definition and energy balance
For incident radiant flux and reflected radiant flux , reflectance is
Radiant flux is power carried by radiation. A reflectance measurement must specify the relevant spectral range and collection geometry. Collecting only the narrow beam reflected by a polished surface gives a different quantity from collecting all radiation returned into the hemisphere above it.
For a passive system in which incident radiation is accounted for by reflection, transmission, and absorption,
where is transmittance and is absorptance. These quantities must refer to compatible wavelengths and geometries. For an opaque sample, , so .
This balance distinguishes reflected incident radiation from radiation emitted by the sample itself. Thermal emission, fluorescence, or other wavelength-converting processes require separate accounting when they contribute to a detector signal.
Reflectance is also distinct from an amplitude reflection coefficient. In a simple plane-wave problem, the complex electric-field reflection coefficient is
For incident and reflected waves propagating in the same lossless medium,
Unlike reflectance, contains phase information, which is important in interference and multilayer optics.
Spectral and broadband reflectance
Spectral reflectance, written , describes reflectance as a function of wavelength. Materials often reflect strongly in one part of the electromagnetic spectrum and weakly in another. A surface that appears dark in visible light may nevertheless reflect substantial near-infrared radiation.
A broadband reflectance is a weighted average over a wavelength interval. For fixed illumination geometry and incident spectral irradiance ,
Consequently, the same surface can have different broadband reflectances under different source spectra. An instrument's spectral response may introduce additional weighting into its reported value.
Visible appearance is not determined by reflectance alone. It also depends on the illuminant, viewing geometry, and the spectral sensitivity of the eye or detector. Photometrically weighted reflectance, which incorporates human visual sensitivity, should therefore be distinguished from an unweighted radiometric measurement.
Angular dependence and surface scattering
Reflection can be concentrated around a particular direction or distributed across many directions.
- Specular reflection is concentrated near the mirror direction, as for a smooth polished surface.
- Diffuse reflection distributes reflected radiation over a broad range of directions.
- Mixed reflection combines a specular component with diffuse or broader scattering components.
Diffuse reflection does not necessarily mean uniform scattering. An ideal Lambertian surface has reflected radiance independent of viewing direction under fixed illumination; many real matte surfaces only approximate this behavior.
Surface roughness, particles, pores, and internal interfaces can redistribute radiation through scattering. Roughness is relative to wavelength: a surface that is optically smooth at a long wavelength may be rough at a much shorter one.
Bidirectional reflectance distribution function
The bidirectional reflectance distribution function (BRDF) describes the angular distribution of reflected radiation. At a specified wavelength,
where is reflected radiance, is incident irradiance, and and specify illumination and reflection directions. Its unit is inverse steradian, not a dimensionless fraction.
For illumination from a single direction, integrating the BRDF over all reflected directions gives the directional–hemispherical reflectance:
where is measured from the surface normal.
Common measurement geometries include:
- Directional–hemispherical reflectance: directional illumination with collection over the reflected hemisphere.
- Bihemispherical reflectance: hemispherical illumination and hemispherical collection, with the angular distribution of illumination specified.
- Restricted-angle measurements: illumination and collection over defined, finite angular ranges.
A reflectance factor compares the radiation reflected in a specified geometry with that from an ideal perfectly reflecting Lambertian reference under the same illumination. It can exceed 1 when a surface concentrates reflected radiation toward the detector. This does not imply that the surface reflects more total energy than it receives. Similarly, a BRDF value greater than is not a violation of energy conservation.
Physical determinants
Refractive index and Fresnel reflection
At a smooth boundary, reflection depends on the optical properties of the adjoining media. For normal incidence between two nonabsorbing, nonmagnetic media with refractive indices and , the Fresnel equations give
For example, an air–glass interface with indices approximately 1 and 1.5 reflects about 4% of normally incident power. This is the reflectance of one interface, not necessarily that of an entire glass plate.
At oblique incidence, reflectance differs for polarization perpendicular and parallel to the plane of incidence. Under suitable conditions, the parallel-polarized component vanishes at Brewster's angle. At an interface from a higher-index to a lower-index lossless medium, total internal reflection occurs beyond the critical angle.
Absorbing media require a complex refractive index. Metals can have high reflectance over broad spectral ranges, but their reflectance remains wavelength-dependent and is generally below unity.
Layers, microstructure, and absorption
In thin films, reflections from different interfaces interfere. Depending on film thickness, wavelength, incidence angle, and refractive indices, this interference can suppress reflection or enhance it. Anti-reflective coatings and dielectric mirrors exploit this principle.
In paints, powders, snow, vegetation, and biological tissues, measured reflectance often includes radiation that enters the material and undergoes multiple scattering before emerging. Its spectrum depends on both absorption and scattering. Composition alone is therefore insufficient to predict reflectance: particle size, porosity, moisture, layer thickness, and the underlying substrate can also matter.
Measurement
Reflectance is measured with reflectometers, spectrophotometers, and angularly resolved optical instruments. Reliable results require a defined wavelength range, illumination geometry, collection geometry, and reference scale.
An integrating sphere collects radiation over a large range of directions and is widely used for hemispherical measurements. Instrument configurations may include or exclude the specular component. This distinction is important for glossy samples and for comparisons between instruments.
A gonioreflectometer varies illumination and observation directions to characterize angular scattering. Reflectance spectroscopy records wavelength-dependent behavior and can reveal absorption features associated with composition or structure.
Measurements commonly compare a sample with a calibrated reference. Such references are not perfect reflectors: their assigned spectral and angular properties must be incorporated through calibration. Important contributions to measurement uncertainty include stray light, detector nonlinearity, finite angular apertures, wavelength bandwidth, sample nonuniformity, and errors in positioning.
Dark samples are especially sensitive to stray light. Highly specular samples require careful alignment because a small angular error can move much of the reflected beam outside the detector aperture.
Applications and related quantities
Remote sensing and albedo
In remote sensing, spectral reflectance helps distinguish vegetation, soils, snow, water, and minerals. A satellite initially measures radiance at the sensor, not intrinsic surface reflectance. Estimating surface reflectance requires accounting for illumination and viewing geometry and, where relevant, absorption and scattering by the atmosphere.
Albedo is closely related to reflectance but usually denotes a hemispherically integrated quantity, often averaged over a broad solar wavelength range. Planetary science distinguishes several albedo definitions, including Bond albedo and geometric albedo, which are not interchangeable. Albedo is important in the Earth's energy budget because it determines the fraction of incoming solar radiation returned to space.
Optical engineering and appearance
Reflectance determines losses and useful signal levels in mirrors, lenses, displays, cameras, and optical sensors. High reflectance is desirable for many mirrors, whereas low reflectance is desirable for lens surfaces, light traps, and devices intended to absorb incident radiation.
Spectral and angular reflectance also underpin color measurement and realistic rendering. A single reflectance number cannot fully describe gloss, metallic appearance, iridescence, or the dependence of appearance on viewing angle.
Reflectance and thermal emission
Reflectance is related to emissivity through energy balance and Kirchhoff's law of thermal radiation. Under the conditions to which that law applies, emissivity equals absorptivity for matching wavelength, direction, and polarization. For an opaque reciprocal surface, this allows the appropriate directional spectral emissivity to be inferred from the corresponding reflectance as
The matching conditions are essential. Low visible reflectance does not by itself imply high thermal-infrared emissivity, because visible light and thermal radiation occupy different wavelength ranges.