Kirchhoff’s law of thermal radiation states that, at thermodynamic equilibrium, a body’s ability to emit thermal electromagnetic radiation equals its ability to absorb radiation at the same wavelength, direction, and polarization, with the appropriate correspondence between incoming and outgoing modes. In its familiar form for reciprocal materials, the law is expressed as equality between spectral emissivity and spectral absorptivity. It establishes why good absorbers are also good thermal emitters and connects the radiation of real materials to the universal spectrum of blackbody radiation.
Statement and definitions
For a conventional reciprocal surface at absolute temperature , the spectral, directional form is
where:
- is wavelength;
- specifies a viewing or illumination direction relative to the surface;
- specifies polarization;
- is spectral directional emissivity;
- is spectral directional absorptivity.
The incident and emitted directions are paired by reversal of the propagation path. In ordinary surface terminology, illumination from a given direction is compared with emission toward that direction.
Absorptivity is the fraction of incident radiant power that a body absorbs, rather than reflects or transmits. Emissivity is the ratio of the body’s emitted thermal radiance to the radiance of a blackbody at the same temperature, wavelength, and corresponding polarization. Using radiances summed over both polarizations,
where includes only radiation thermally generated by the body, not reflected or transmitted radiation from its surroundings.
A blackbody absorbs all incident radiation and therefore has absorptivity and emissivity equal to one. A real material may have values close to one in some wavelength ranges and close to zero in others.
Kirchhoff’s law concerns matching optical conditions. It does not state that a material’s visible-light absorptivity equals its infrared emissivity, or that a single emissivity value describes every direction and wavelength.
Equilibrium basis
The law follows from the requirements of thermodynamics, particularly the second law of thermodynamics.
Consider a body inside an enclosure whose walls and contents are all at the same temperature. The equilibrium radiation field inside the enclosure has the blackbody spectrum. At a given wavelength and for corresponding incoming and outgoing modes, the body absorbs radiation from that field and emits radiation into it.
If its emissivity exceeded its absorptivity for the relevant mode, it would emit more thermal radiation into that mode than it absorbed from the equilibrium field. If its absorptivity exceeded its emissivity, the reverse imbalance would occur. For ordinary reciprocal systems, equilibrium requires these exchanges to balance, giving
Dividing by the blackbody radiance yields Kirchhoff’s law.
This reasoning concerns the emitted component of radiation. A reflective object in an equilibrium enclosure can have the same outgoing radiance as a blackbody even though its own thermal emission is small: reflected enclosure radiation supplies the difference.
The directional statement also relies on electromagnetic reciprocity. Energy balance alone should not be taken as a proof of pairwise equality for arbitrary nonreciprocal optical systems.
Connection with Planck’s law
Kirchhoff’s law relates emission to absorption but does not, by itself, determine the blackbody spectrum. That spectrum is given by Planck’s law:
where is the Planck constant, is the speed of light in vacuum, and is the Boltzmann constant.
Combining the two laws gives, for the ordinary unpolarized case,
The thermal emission spectrum therefore depends on two distinct factors:
- The universal blackbody spectrum at the body’s temperature.
- The material’s wavelength- and direction-dependent absorption properties.
For example, a material may absorb strongly in a narrow infrared band and weakly elsewhere. At a temperature where appreciable blackbody radiation falls in that band, it can emit strongly there while emitting weakly at neighboring wavelengths.
Spectral and total quantities
The distinction between spectral and integrated quantities is essential.
Spectral emissivity describes emission at a particular wavelength. Total emissivity describes emission integrated over all wavelengths. Directional quantities describe a particular direction, whereas hemispherical quantities include all outward directions with the appropriate projected-area weighting.
For hemispherically averaged spectral emissivity, total emissivity is
where is blackbody spectral radiant exitance.
By contrast, total absorptivity for specified illumination is weighted by the incident spectrum and its angular distribution. Consequently, total emissivity and total absorptivity need not be equal when the incident radiation differs from equilibrium blackbody radiation at the body’s temperature.
This explains why a surface can absorb sunlight effectively yet emit thermal infrared radiation weakly without violating Kirchhoff’s law. Sunlight and terrestrial-temperature thermal emission occupy substantially different parts of the electromagnetic spectrum.
Graybody approximation
A graybody is an idealized body whose emissivity is independent of wavelength over the range of interest. If its hemispherical emissivity can be treated as a constant, its total emitted radiant power per unit area is
where is the Stefan–Boltzmann constant.
This expression combines Kirchhoff’s framework with the integrated blackbody emission law. The graybody approximation is useful in engineering, but many metals, gases, coatings, and optical structures are strongly nongray.
Reflection, transmission, and absorption
For a passive surface or layer under specified illumination, conservation of energy gives
where is reflectivity and is transmissivity. Reflected and transmitted fractions must include all relevant outgoing directions.
For an opaque body, , so that Kirchhoff’s law gives
Thus, a highly reflecting opaque surface is a weak thermal emitter at the same wavelength and corresponding direction. This is why polished metals often have low infrared emissivity.
For a semitransparent material, low reflectivity alone does not imply high emissivity: much of the incident radiation may pass through rather than be absorbed. Emission then depends on absorption within the material, its thickness, and internal reflections.
Gases and radiative transfer
Kirchhoff’s law also has a local form in radiative transfer. In a medium without scattering, the transfer equation along a ray can be written
where is spectral radiance per unit frequency, is the absorption coefficient, and is the thermal emission coefficient in the corresponding transfer convention.
Under local thermodynamic equilibrium,
or, equivalently,
where is the thermal source function. The coefficients must be defined consistently, including the treatment of stimulated emission.
Local thermodynamic equilibrium does not require the entire radiation field to be a blackbody field. It requires the relevant material populations to be described by the local equilibrium temperature sufficiently well for the thermal source relation to apply.
This formulation is central to astrophysics and atmospheric radiation. A gas can emit at wavelengths where it absorbs, yet appear as either an emission or absorption feature depending on its temperature, optical depth, and the radiation behind it. Scattering adds terms to the transfer equation; the total source function then need not equal the Planck function even when the material is locally in thermodynamic equilibrium.
Applications
Temperature measurement
Infrared thermometers and thermal cameras infer temperature from measured radiance. Kirchhoff’s law connects emissivity to absorption and reflection properties that can be measured independently.
The observed signal may contain emitted, reflected, and transmitted components. For an opaque surface, a simplified directional description is
A low-emissivity surface can therefore appear dominated by reflections of its surroundings. This matters in industrial inspection, furnace measurements, and radiometric calibration.
Thermal engineering and selective surfaces
Radiative heat-transfer calculations use emissivity to estimate energy exchange between surfaces. Kirchhoff’s law permits absorption measurements to characterize thermal emission under corresponding conditions.
Selective coatings exploit spectral differences rather than circumventing the law. Solar absorbers can combine strong absorption in solar wavelengths with weak emission in thermal infrared wavelengths. Conversely, radiative-cooling surfaces can reflect much of the solar spectrum while emitting strongly through infrared transmission windows of the Earth’s atmosphere.
Spectroscopy and astronomy
The relationship between absorption and emission supports the interpretation of spectral lines in spectroscopy and astronomy. Whether a particular transition produces an observed bright or dark line depends on radiative transfer and the physical state of the emitting and absorbing regions, not simply on the existence of that transition.
Scope and limitations
The familiar equality requires several qualifications:
- Thermal emission: It does not directly describe fluorescence, laser emission, chemical light production, or other nonequilibrium radiation.
- Corresponding conditions: Wavelength, direction, polarization, temperature, and material state must be matched appropriately.
- Reciprocity: In nonreciprocal systems, such as some materials under an applied magnetic field, same-direction emissivity and absorptivity can differ. More general relations are needed; global equilibrium energy balance remains necessary.
- Local equilibrium: The thermal source-function form can fail when atomic or molecular populations depart substantially from local equilibrium.
- Optical geometry: Standard surface-radiance formulas describe propagating far-field radiation. Near-field heat transfer includes evanescent electromagnetic modes and requires a more general treatment.
For small particles and structured optical systems, absorption cross sections and mode-resolved emission can be more appropriate than macroscopic surface emissivity. Blackbody bounds expressed per unit geometrical area should not be applied indiscriminately to such systems.
Historical development
Gustav Kirchhoff developed the law in 1859–1860 while investigating the relationship between emission and absorption spectra. His work established that the ratio of a body’s thermal emission to its absorptivity, under matching equilibrium conditions, is a universal function of wavelength and temperature.
Kirchhoff did not determine the explicit form of that universal function. Finding it became the blackbody-radiation problem. Max Planck obtained the successful spectral formula in 1900, introducing energy quantization into its derivation. Kirchhoff’s equilibrium argument and Planck’s spectral law thus answer different questions: the former connects a material’s emission to its absorption, while the latter specifies the universal radiation spectrum.