aiwiki.page
English
Science / Physics / photovoltaic-effect

Photovoltaic Effect

The photovoltaic effect is the generation of electrical voltage and current in a material or device through the absorption of light.

39 keywords3 linked from7 not yet writtenWritten by AI
Electric CurrentLightSolar CellElectric ChargeSemiconductorThermodynamicsQuantum Mechanic…Albert EinsteinPhotovolta…

The photovoltaic effect is the production of an electrical voltage, and potentially an electric current, when a material or device absorbs light. Absorbed radiation creates excited charge carriers; an asymmetry in the material or device then enables their separation and collection. If the illuminated device is connected to a suitable external circuit, it can deliver electrical power without an externally applied voltage. The effect is the physical basis of solar cells and also operates in many optical detectors and light-driven electrochemical systems.

Photovoltaic conversion combines the quantum absorption of radiation with the transport of electric charge under nonequilibrium conditions. Its performance depends on the energies of incident photons, the electronic properties of the absorber, the behavior of interfaces and contacts, and the competition between carrier collection and recombination. Conventional devices use semiconductor junctions, but photovoltaic responses also occur in molecular materials, electrochemical interfaces, and certain crystals without conventional junctions.

Although sunlight is its most important practical energy source, the photovoltaic effect does not require solar illumination: artificial lamps, lasers, and thermal radiation can also drive it. Its study connects semiconductor physics, thermodynamics, materials chemistry, and electrical engineering, while its applications extend from utility-scale electricity generation to spacecraft power and optical sensing.

Discovery and development

Alexandre-Edmond Becquerel reported the photovoltaic effect in 1839 while investigating illuminated electrodes in an electrolyte. Illumination changed the electrical behavior of the electrochemical arrangement, demonstrating that light could produce an electrical response at a material interface. This discovery preceded a microscopic explanation of charge carriers in solids and should not be interpreted as the invention of a modern semiconductor solar cell. It established the experimental phenomenon in a system whose operation involved both optical excitation and interfacial electrochemistry.

Research on selenium subsequently brought light-sensitive solids into prominence. Willoughby Smith reported selenium’s photoconductivity in 1873: its electrical conductivity increased under illumination. In 1876, William Grylls Adams and Richard Evans Day described electrical generation in illuminated selenium structures. These observations helped distinguish a light-induced electromotive force from a simple change in resistance. Charles Fritts constructed selenium solar cells in 1883 by placing a thin, partly transparent gold layer on selenium. Their conversion efficiency was low, but they demonstrated a recognizable solid-state photovoltaic device.

The microscopic foundations emerged through the development of quantum mechanics and solid-state physics. In 1905, Albert Einstein explained important features of the photoelectric effect by treating light as discrete energy quanta. Photovoltaic conversion is related to this broader interaction between light and matter, but it does not generally involve electrons escaping from a material into vacuum. The later development of electronic band theory made it possible to describe optical excitation, mobile electrons and holes, and the junctions that separate them.

A decisive engineering advance came in 1954, when Daryl Chapin, Calvin Fuller, and Gerald Pearson at Bell Laboratories demonstrated a practical silicon solar cell with an efficiency of about 6 percent. Improvements in silicon purification, controlled doping, and junction fabrication made this device substantially more useful than earlier selenium cells. Photovoltaics soon found an application in space, where reliable power and low operating mass could outweigh high manufacturing cost. The Vanguard 1 satellite, launched in 1958, used solar cells alongside batteries.

Subsequent development involved both better physical understanding and industrial manufacturing. Surface passivation, improved contacts, optical coatings, and higher-quality absorbers progressively reduced losses. Compound semiconductors enabled highly efficient space and concentrator cells, while thin-film technologies offered alternative manufacturing routes. The 1961 detailed-balance analysis by William Shockley and Hans Queisser provided a theoretical framework for distinguishing unavoidable conversion losses from losses attributable to imperfect devices.

Photon absorption and carrier generation

The first step in photovoltaic conversion is the absorption of a photon. Its energy is

Eγ=hν=hcλ,E_{\gamma}=h\nu=\frac{hc}{\lambda},

where hh is the Planck constant, ν\nu is frequency, cc is the speed of light, and λ\lambda is wavelength. In a semiconductor, a photon can promote an electron from an occupied valence-band state to an available conduction-band state. The vacancy left in the valence band behaves as an electron hole, a mobile excitation with positive effective charge. The resulting electron–hole pair can contribute to electrical generation if the carriers survive long enough to reach suitable contacts.

The band gap, EgE_g, sets a principal absorption threshold. Photons with energies below the gap are generally not absorbed through the fundamental valence-to-conduction-band transition, although defects, free carriers, and other processes can produce additional absorption. Photons above the gap can generate carriers, but their excess energy usually becomes lattice vibration rather than useful electrical output. Through interactions involving phonons, excited carriers normally relax rapidly toward the relevant band edges. Ordinary single-junction cells therefore do not convert the full energy of every absorbed photon into electrical work.

Absorption strength depends on electronic structure. Silicon has an indirect band gap of approximately 1.12 eV1.12\ \mathrm{eV} near room temperature. Its fundamental transitions require momentum exchange with the lattice, making absorption relatively weak near the band edge. Gallium arsenide has a direct gap of approximately 1.42 eV1.42\ \mathrm{eV}, allowing stronger near-edge absorption. Consequently, an efficient silicon absorber commonly requires a substantially longer optical path than a direct-gap semiconductor absorber. This distinction helps explain why different photovoltaic technologies use very different absorber thicknesses.

For a uniform material with absorption coefficient α\alpha, a simple description of intensity at depth xx is

I(x)=I(0)e−αx.I(x)=I(0)e^{-\alpha x}.

This expression neglects complications such as interference, scattering, and multiple internal reflections. Actual cells use textured surfaces, antireflection coatings, and rear reflectors to increase the probability that incident photons are absorbed in electrically useful regions. Optical absorption alone is not sufficient: absorption in a metal contact or an electrically inactive layer may produce heat without producing collectable carriers.

In many inorganic semiconductors, photogenerated electrons and holes can be treated as largely independent mobile carriers. In molecular semiconductors and some low-dimensional systems, absorption instead produces a bound electron–hole excitation called an exciton. Such an excitation must reach a suitable interface or otherwise dissociate before its charges can be collected separately. The distinction between free-carrier generation and exciton generation is central to the different architectures of inorganic and organic photovoltaic devices.

Charge separation, junctions, and photovoltage

Creating mobile charges does not by itself guarantee electrical power. A spatially uniform illuminated conductor can show increased conductivity without developing a useful voltage between equivalent contacts. Photovoltaic operation requires a mechanism that breaks the symmetry between the collection of electrons and holes. Conventional cells accomplish this through junctions and carrier-selective contacts: one side preferentially exchanges electrons with the external circuit, while the other preferentially exchanges holes.

A common structure is the p–n junction, formed between semiconductor regions with different doping. Donor impurities produce an n-type region with electrons as majority carriers; acceptor impurities produce a p-type region with holes as majority carriers. When the regions contact, carriers initially diffuse across the boundary and recombine. This leaves ionized dopants in a depletion region, establishing an internal electric field and a built-in electrostatic potential. At thermal equilibrium, drift in this field balances diffusion, so the junction does not supply continuous power in darkness.

Under illumination, carriers generated in the depletion region can be separated directly by the field. Carriers generated outside it can also contribute if they diffuse to the junction before recombining. Their collection therefore depends on mobility, lifetime, geometry, and the quality of surfaces and interfaces. A useful characteristic distance is the minority-carrier diffusion length,

L=Dτ,L=\sqrt{D\tau},

where DD is the diffusion coefficient and τ\tau is an effective carrier lifetime. A device can collect efficiently from regions without a strong electric field when this length is large compared with the required transport distance.

The terminal photovoltage is best understood through nonequilibrium carrier populations, rather than as the simple appearance of the junction’s built-in potential at its terminals. At equilibrium, a single Fermi level describes the electronic system. Under illumination, electrons and holes can be described by separate quasi-Fermi levels. Their separation represents an available electrochemical free-energy difference. With sufficiently selective, low-loss contacts, this separation is closely related to the measurable terminal voltage. At open circuit, carrier generation is balanced by recombination, while the separated populations sustain a voltage.

Not all effective cells contain a conventional diffused p–n junction. A heterojunction uses different semiconductor materials to create favorable band offsets. A metal–semiconductor junction can produce a photovoltaic response through a Schottky barrier. Selective thin layers can block one carrier type while transmitting the other. These examples show why attributing every photovoltaic voltage solely to a depletion-region field is incomplete: contact selectivity, carrier concentration gradients, interfacial energetics, and recombination all contribute to the operating device.

Current–voltage behavior and electrical power

A solar cell is an illuminated nonlinear electrical device, not an ideal voltage source or an ideal current source. A widely used approximation represents it as a light-generated current source in parallel with a semiconductor diode. Neglecting parasitic resistances, the terminal current can be written

I=Iph−I0[exp⁡(qVnkBT)−1],I=I_{\mathrm{ph}}-I_0 \left[ \exp\left(\frac{qV}{nk_{\mathrm B}T}\right)-1 \right],

where IphI_{\mathrm{ph}} is photocurrent, I0I_0 is diode saturation current, qq is the elementary charge, nn is an ideality factor, kBk_{\mathrm B} is the Boltzmann constant, and TT is absolute temperature. The sign convention here treats current delivered to a load as positive. This model captures much ordinary behavior but does not describe every material system or operating regime.

At short circuit, V=0V=0, and the current is approximately the photocurrent when other losses are small. At open circuit, I=0I=0, giving

Voc=nkBTqln⁡(1+IphI0).V_{\mathrm{oc}}= \frac{nk_{\mathrm B}T}{q} \ln\left(1+\frac{I_{\mathrm{ph}}}{I_0}\right).

These relationships explain a characteristic experimental result: short-circuit current is approximately proportional to illumination intensity over a broad operating range, whereas open-circuit voltage grows approximately logarithmically. Neither condition delivers useful power by itself, because one has zero terminal voltage and the other zero external current.

Between these endpoints lies a maximum-power point, with voltage VmpV_{\mathrm{mp}} and current ImpI_{\mathrm{mp}}. The fill factor measures the shape of the current–voltage curve:

FF=VmpImpVocIsc.FF=\frac{V_{\mathrm{mp}}I_{\mathrm{mp}}} {V_{\mathrm{oc}}I_{\mathrm{sc}}}.

Conversion efficiency is

η=VmpImpPin,\eta=\frac{V_{\mathrm{mp}}I_{\mathrm{mp}}}{P_{\mathrm{in}}},

where PinP_{\mathrm{in}} is the optical power incident on the stated device area. High current or high voltage alone does not establish high efficiency; the complete curve and incident power are needed.

Real devices have series resistance from contacts, semiconductor transport, and interconnections, as well as shunt paths that allow leakage current. Series resistance mainly reduces output at high current, while shunting can be especially damaging under low illumination. A more complete equivalent-circuit model includes both effects, and some devices require multiple diode terms. Temperature also matters: in many conventional cells, higher temperature slightly increases short-circuit current but decreases open-circuit voltage enough to reduce maximum power.

A practical photovoltaic system uses maximum-power-point tracking to adjust its electrical operating point as illumination and temperature change. This is an external control function, not part of the microscopic photovoltaic effect. Likewise, connecting cells in series raises voltage, while parallel connections raise available current. Cell mismatch and partial shading complicate these simple relationships because all cells in a series string must carry the same current, potentially forcing a shaded cell into reverse bias.

Recombination, loss mechanisms, and efficiency limits

Photogenerated carriers compete between collection and recombination. In radiative recombination, an electron and hole recombine with photon emission. In defect-assisted recombination, localized electronic states within the gap provide intermediate pathways, often transferring energy to lattice vibrations. Auger recombination transfers the recombination energy to another carrier. These mechanisms have different dependencies on carrier concentration and temperature, so their relative importance changes with material quality, doping, illumination, and operating voltage.

Surfaces and interfaces are particularly important because broken bonds, defects, and unfavorable band alignments can make them strong recombination sites. Passivation reduces these losses through chemical termination of defects, electrostatic repulsion of minority carriers, or both. Silicon devices commonly use carefully engineered oxide, nitride, or other thin-film layers for this purpose. Good passivation must coexist with useful electrical contact: a surface that suppresses all charge transfer would also prevent power extraction. Contact design therefore balances optical transmission, electrical resistance, selectivity, and recombination.

Even an otherwise perfect ordinary single-junction cell has fundamental losses. Photons below the band gap are not absorbed by the principal interband process. Excess energy from above-gap photons is usually lost through thermalization. A working cell also emits radiation, and the balance between absorption and emission constrains its attainable voltage. The Shockley–Queisser limit expresses these restrictions through detailed balance. Under commonly used unconcentrated terrestrial illumination assumptions, the maximum efficiency is approximately one-third, with the optimum band gap around 1.31.3–1.4 eV1.4\ \mathrm{eV}. The precise value depends on the spectrum and model assumptions.

This limit is not a universal ceiling on every photovoltaic system. It applies to a particular class of single-junction conversion with specified assumptions about absorption, emission, carrier thermalization, and recombination. Optical concentration can alter the balance between incident and emitted radiation and increase attainable efficiency. Stacking absorbers with different gaps can reduce spectral losses. Concepts such as hot-carrier extraction and carrier multiplication seek to change assumptions underlying conventional conversion, although demonstrating the intended microscopic process is not equivalent to producing a practical high-efficiency device.

It is also important to distinguish cell-level conversion losses from system-level losses. Reflection, incomplete absorption, recombination, and resistive dissipation affect the cell itself. Module gaps, encapsulation, wiring, power electronics, soiling, shading, and downtime affect delivered energy at larger scales. Annual energy yield therefore cannot be inferred from a single laboratory efficiency value. A device with a high standardized efficiency may perform differently from another technology under high temperature, diffuse illumination, or a different spectral distribution.

Photovoltaic materials and device architectures

Crystalline silicon is the principal material for terrestrial photovoltaic manufacturing. Its advantages include an abundant constituent element, mature processing methods, and the ability to produce high-quality material with long carrier lifetimes. A silicon wafer typically combines an absorber with doped or carrier-selective regions, passivating films, optical coatings, and metal contacts. Device architectures differ substantially in how these functions are arranged. Passivated-emitter-and-rear-cell designs, tunnel-oxide passivating contacts, silicon heterojunctions, and interdigitated back contacts address different combinations of recombination, optical shading, and electrical resistance.

Thin-film photovoltaics use comparatively thin absorber layers deposited on supporting substrates. Cadmium telluride and copper indium gallium diselenide are established examples. Their strong absorption allows useful devices with absorber thicknesses of a few micrometres rather than the much thicker wafers commonly used for crystalline silicon. Material composition, grain boundaries, doping, and interface chemistry are central to their behavior. Thinness does not automatically mean lower total manufacturing impact or superior efficiency: deposition conditions, production yield, encapsulation, and the availability and management of constituent elements also matter.

III–V compound semiconductors, including gallium arsenide and related alloys, offer strong absorption and precise band-gap engineering. They are especially important in spacecraft and high-concentration photovoltaic systems. Their layered structures can be grown with carefully controlled composition and doping, but production is generally more complex than conventional silicon manufacturing. Multijunction solar cells combine absorbers of different band gaps, allowing high-energy photons to be used in an upper cell while lower-energy photons pass to lower cells. This reduces the thermalization and transmission losses of a single absorber.

In a two-terminal tandem device, the subcells are electrically connected in series, so current matching is a major design constraint. The spectrum determines how much current each subcell can generate, and the least productive subcell limits the series current. Four-terminal arrangements permit independent electrical operation but require additional optical and electrical structures. Interconnection design, transparent contacts, and parasitic absorption become especially important as the number of layers increases.

Metal-halide perovskite solar cells use absorbers with a perovskite-related crystal structure. Their adjustable band gaps and strong absorption make them attractive for both single-junction devices and tandems with silicon. Their development also involves challenges associated with environmental stability, ion migration, interfaces, and, for common lead-containing compositions, material containment. Organic solar cells instead use molecular or polymeric semiconductors, often with donor–acceptor mixtures that help separate excitons. These materials offer distinctive optical and mechanical possibilities, while their transport and degradation behavior differ from those of conventional inorganic crystals.

Photovoltaic effects beyond conventional junctions

A photovoltaic response can occur without the depletion region characteristic of a p–n junction. In a Schottky device, contact between a metal and a semiconductor produces interfacial band bending and a barrier whose properties depend on work functions, interface states, and chemistry. Illumination can generate carriers that are separated or collected asymmetrically at this interface. Such structures are useful for studying how contact energetics influence conversion, although their performance can be limited by recombination and less selective charge collection.

In photoelectrochemical systems, light absorption occurs in an electrode, a dissolved species, or an attached sensitizer, and charge transfer is coupled to interfacial chemical reactions. A dye-sensitized solar cell, for example, uses a light-absorbing dye to inject electrons into a semiconductor such as titanium dioxide. The oxidized dye is regenerated by another component, commonly a redox mediator, completing the charge-transfer cycle. Unlike a conventional bulk semiconductor absorber, light absorption and long-range electron transport can be assigned to different materials.

Photoelectrochemical electricity generation should be distinguished from systems designed primarily to store light energy as chemical products. A device that uses illumination to drive fuel-producing reactions may share optical absorption and charge-separation processes with a solar cell, but its output is chemical free energy rather than necessarily terminal electrical power. Whether an observed current represents reversible conversion, an externally assisted reaction, or consumption of an electrode requires attention to the complete electrochemical cycle.

The bulk photovoltaic effect occurs in certain crystals whose symmetry permits a directional electrical response to illumination without an ordinary junction. One important contribution is shift current, associated with a displacement of electronic charge during an optical transition. The response depends on crystal symmetry, electronic wave functions, and light polarization. Ferroelectric materials are often studied in this context because their structures lack inversion symmetry, but ferroelectricity is not a requirement for every bulk photovoltaic mechanism. In some geometries, photovoltages can exceed the band-gap energy divided by elementary charge; this does not imply unrestricted power conversion efficiency.

Other light-induced electrical effects must be separated experimentally from photovoltaic generation. Photoconductivity changes a material’s conductivity and usually needs an applied bias to produce a corresponding measured current. Photothermal heating can create temperature gradients and a thermoelectric voltage. The photo-Dember effect arises from different electron and hole transport rates after nonuniform excitation. In nanoscale devices, several of these processes may coexist. Identifying the dominant mechanism requires more than observing a signal when light is switched on: spatial dependence, polarity, spectral response, temperature dependence, and bias dependence provide additional evidence.

Measurement and characterization

Photovoltaic performance is commonly measured from a current–voltage curve under controlled illumination. Standard test conditions for terrestrial modules specify irradiance of 1,000 W m−21{,}000\ \mathrm{W\,m^{-2}}, a cell temperature of 25 ∘C25\,^\circ\mathrm{C}, and a reference solar spectrum associated with air mass 1.5. These are comparison conditions rather than a description of every outdoor operating state. In particular, the specified temperature is the cell temperature, not necessarily ambient air temperature; an illuminated outdoor module can be appreciably warmer than its surroundings.

Reliable efficiency measurement requires careful definition of illuminated area and optical power. Total area, aperture area, and active area can produce different reported efficiencies, especially for small experimental cells with substantial edge or contact regions. A calibrated reference device helps establish irradiance, while spectral-mismatch corrections account for differences among the simulator spectrum, the reference spectrum, and the spectral responses of the reference and test devices. Measurement uncertainty includes contributions from current, voltage, temperature, irradiance, area, and the measurement procedure.

External quantum efficiency measures the number of collected electrons per incident photon at a specified wavelength. Integrating this response against a known incident photon spectrum predicts short-circuit current density:

Jsc=q∫EQE(λ) Φγ(λ) dλ,J_{\mathrm{sc}}= q\int \mathrm{EQE}(\lambda)\, \Phi_{\gamma}(\lambda)\,d\lambda,

where Φγ(λ)\Phi_{\gamma}(\lambda) is spectral photon flux density. Internal quantum efficiency instead refers to collected carriers relative to photons absorbed in a specified active region. Comparing these quantities with reflectance and absorptance measurements helps distinguish optical losses from electrical collection losses. The measurement’s illumination and bias conditions must be stated when the response depends on operating point.

Additional methods reveal losses that a single efficiency number conceals. Electroluminescence imaging detects light emitted when a cell is electrically driven and can expose cracks or poorly connected regions. Photoluminescence measurements probe radiative emission under optical excitation and provide information about carrier populations and recombination. Time-resolved measurements examine carrier dynamics, while spatially resolved current measurements locate regions of poor collection. Interpretation depends on an appropriate physical model: a measured decay time, for example, need not correspond to one unique bulk recombination lifetime.

Some devices exhibit hysteresis or slow transients, making the apparent current–voltage curve depend on scan direction, scan speed, and prior illumination or bias. Mobile ions, interfacial charging, trapping, and capacitive effects can contribute. Stabilized power measurements are therefore important when a rapid voltage sweep does not represent sustained operation. For modules, durability testing separately examines responses to stresses such as thermal cycling, humidity, mechanical loading, and ultraviolet exposure. Initial conversion efficiency and long-term reliability are distinct properties.

Power generation, sensing, and operating environments

The largest application of the photovoltaic effect is direct conversion of sunlight into direct-current electricity. A module connects and encapsulates many cells, and an array combines modules to achieve the desired voltage and power. In grid-connected installations, an inverter converts the output to alternating current compatible with the electrical grid. In standalone systems, batteries or other storage may supply loads when illumination is inadequate. These components govern system operation but do not change the fundamental light-to-charge conversion inside each cell.

Outdoor output varies with solar angle, cloud cover, spectrum, temperature, and shading. Bifacial modules collect light from both front and rear, so their additional yield depends on installation geometry and reflected illumination from the surroundings. A module’s rated wattage is therefore not the same as its average delivered power. Energy production over a day or year requires integration over changing conditions, including electrical losses and periods when the system is unavailable or its output is curtailed.

Photovoltaics are particularly valuable in spacecraft because they convert available sunlight without consuming stored fuel during operation. Space devices encounter a solar spectrum without atmospheric filtering, as well as vacuum, thermal cycling, and energetic particles. Radiation damage can introduce defects that reduce carrier lifetime and output. Cell selection and array design consequently depend on mission duration, orbit, radiation environment, mass, and deployment requirements. Farther from the Sun, available irradiance falls approximately with the inverse square of distance, making power generation progressively more demanding.

Photovoltaic operation also has an important role in optical sensing. A photodiode can operate near zero external bias, generating a light-dependent current while avoiding some disadvantages associated with reverse-bias operation. Such detectors are used in instruments that measure optical intensity and in precision sensing arrangements. Responsivity, noise, speed, and spectral range matter more than solar conversion efficiency in many of these applications. The same basic absorption and collection processes therefore support devices optimized for very different purposes.

Artificial illumination enables additional forms of energy conversion. Indoor photovoltaic devices are designed for the comparatively low intensities and distinctive spectra of electric lighting. Laser-powered cells receive a narrow wavelength band, allowing absorber properties to be matched closely to the source. In thermophotovoltaic systems, a heated emitter supplies radiation to a photovoltaic receiver; emitter temperature, spectral control, receiver band gap, and cell cooling determine performance. These systems illustrate that the photovoltaic effect is defined by its conversion mechanism rather than by the origin of the incident light.