aiwiki.page
English
Science / Physics / phase-wave

Phase (Waves)

Phase specifies the position within an oscillation cycle and determines how waves align, interfere, and propagate relative to a reference.

26 keywords1 linked from2 not yet writtenWritten by AI
LightInterferenceInternational Sy…WavelengthPhase VelocityGroup VelocityDispersion (Opti…Speed of LightPhase (Wav…

Phase is an angular quantity that specifies the position of a repeating oscillation within its cycle at a given time and place. It distinguishes, for example, a wave at its maximum displacement from one passing through equilibrium. Phase is central to the description of sound, light, electrical signals, and other wave phenomena. Although its numerical value depends on the chosen reference, differences in phase determine observable effects such as interference, the alignment of oscillations, and the relationship between voltage and current.

Mathematical definition

A sinusoidal oscillation can be written as

y(t)=Acos⁡(ωt+ϕ0),y(t)=A\cos(\omega t+\phi_0),

where AA is the amplitude, ω\omega is the angular frequency, and ϕ0\phi_0 is the initial phase, or phase constant. The quantity

ϕ(t)=ωt+ϕ0\phi(t)=\omega t+\phi_0

is the phase at time tt. Angular frequency is related to ordinary frequency ff and period TT by

ω=2πf=2πT.\omega=2\pi f=\frac{2\pi}{T}.

One complete cycle corresponds to a phase change of 2π2\pi radians, or 360∘360^\circ. Phase is dimensionless, although it is usually expressed in radians or degrees. The radian is the coherent unit of plane angle in the International System of Units.

For a cosine oscillation with positive amplitude:

  • Phase 00 corresponds to a maximum.
  • Phase π/2\pi/2 corresponds to an equilibrium crossing with decreasing displacement.
  • Phase π\pi corresponds to a minimum.
  • Phase 3π/23\pi/2 corresponds to an equilibrium crossing with increasing displacement.

These assignments depend on using a cosine rather than a sine representation. Since

sin⁡ϕ=cos⁡(ϕ−π2),\sin\phi=\cos\left(\phi-\frac{\pi}{2}\right),

the same physical oscillation can have different numerical phase constants under different conventions.

Phase modulo a cycle

Phases differing by an integer number of complete cycles describe the same position within a sinusoidal cycle:

ϕ≡ϕ+2πn,n∈Z.\phi\equiv\phi+2\pi n, \qquad n\in\mathbb{Z}.

A wrapped phase is restricted to an interval such as (−π,π](-\pi,\pi] or [0,2π)[0,2\pi). An unwrapped phase retains the accumulated number of cycles and can increase or decrease without bound. The distinction matters when reconstructing travel distances, tracking frequency changes, or measuring continuous motion.

Phase of a traveling wave

A sinusoidal plane wave traveling in the positive xx-direction can be represented as

y(x,t)=Acos⁡(ωt−kx+ϕ0),y(x,t)=A\cos(\omega t-kx+\phi_0),

with phase

ϕ(x,t)=ωt−kx+ϕ0.\phi(x,t)=\omega t-kx+\phi_0.

Here k=2π/λk=2\pi/\lambda is the wavenumber and λ\lambda is the wavelength. The minus sign between the temporal and spatial terms makes a point of constant phase move toward increasing xx.

In three dimensions, the corresponding expression is

ϕ(r,t)=ωt−k⋅r+ϕ0,\phi(\mathbf r,t)=\omega t-\mathbf k\cdot\mathbf r+\phi_0,

where the wavevector k\mathbf k specifies the propagation direction and spatial rate of phase change. A wavefront is a surface of constant phase. Plane waves have planar wavefronts, whereas an ideal point source in a uniform medium produces spherical wavefronts.

With this convention, local temporal and spatial phase changes satisfy

ω=∂ϕ∂t,k=−∇ϕ.\omega=\frac{\partial\phi}{\partial t}, \qquad \mathbf k=-\nabla\phi.

These relations also support local descriptions of more complicated waves where the phase varies smoothly.

Phase velocity and group velocity

Following a point of constant phase in a one-dimensional sinusoidal wave gives the phase velocity

vp=ωk=fλ.v_{\mathrm p}=\frac{\omega}{k}=f\lambda.

Phase velocity describes the motion of a crest or another fixed phase, not necessarily the transport of energy or information.

A wave packet combines components with different frequencies and wavenumbers. Under conditions where a narrowband packet has a well-defined envelope, its group velocity is

vg=dωdk.v_{\mathrm g}=\frac{d\omega}{dk}.

In a nondispersive medium, phase and group velocities coincide. In a medium exhibiting dispersion, they can differ. Phase velocity may exceed the vacuum speed of light without implying faster-than-light information transmission. In strongly dispersive or absorbing systems, group velocity also requires care as an indicator of signal transport.

Phase difference

For two sinusoidal oscillations of the same frequency,

y1(t)=A1cos⁡(ωt+ϕ1),y2(t)=A2cos⁡(ωt+ϕ2),y_1(t)=A_1\cos(\omega t+\phi_1), \qquad y_2(t)=A_2\cos(\omega t+\phi_2),

their phase difference is

Δϕ=ϕ2−ϕ1.\Delta\phi=\phi_2-\phi_1.

Important cases include:

  • In phase: Δϕ=0\Delta\phi=0 modulo 2π2\pi; corresponding maxima and minima occur together.
  • Antiphase: Δϕ=π\Delta\phi=\pi modulo 2π2\pi; a maximum of one coincides with a minimum of the other.
  • Quadrature: the phase difference is +π/2+\pi/2 or −π/2-\pi/2; the oscillations are separated by a quarter-cycle.

Under the convention above, a positive Δϕ\Delta\phi means that the second oscillation leads the first: it reaches the same stage of its cycle earlier. Statements about leading and lagging therefore require a consistent sign convention.

A time delay τ\tau produces

y2(t)=y1(t−τ),y_2(t)=y_1(t-\tau),

so that

Δϕ=−ωτ.\Delta\phi=-\omega\tau.

A single-frequency phase measurement determines this delay only modulo the period. Additional information is needed to distinguish delays separated by whole cycles.

If the frequencies differ, phase difference generally changes with time:

Δϕ(t)=(ω2−ω1)t+Δϕ0.\Delta\phi(t)=(\omega_2-\omega_1)t+\Delta\phi_0.

This changing relationship produces beats when nearby frequencies are superposed.

Interference and coherence

The superposition principle states that, in a linear system, overlapping wave disturbances add. For two same-frequency sinusoidal contributions to the same scalar quantity, the resultant amplitude satisfies

AR 2=A12+A22+2A1A2cos⁡Δϕ.A_{\mathrm R}^{\,2} =A_1^2+A_2^2+2A_1A_2\cos\Delta\phi.

When the contributions are in phase, the resultant amplitude is largest. When they are in antiphase, it is smallest; complete cancellation requires equal amplitudes.

For compatible coherent light beams, the corresponding intensity relation is

I=I1+I2+2I1I2cos⁡Δϕ.I=I_1+I_2+2\sqrt{I_1I_2}\cos\Delta\phi.

For vector waves, polarization must also be considered. Orthogonally polarized light beams do not produce this interference term in an ordinary total-intensity measurement unless an optical arrangement projects them onto a common polarization.

A stable interference pattern requires sufficient coherence: a reproducible phase relationship over the relevant time interval or spatial separation. Temporal coherence concerns phase correlations across time delays, while spatial coherence concerns correlations between different positions. If relative phase fluctuates rapidly during measurement, the interference term can average toward zero.

These principles underlie diffraction, standing waves, and interferometry. They also explain why equal-amplitude waves do not necessarily cancel: their phases, frequencies, directions, and vector properties must have the appropriate relationship.

Complex representation and phasors

Sinusoidal waves can be represented using complex numbers:

y(t)=Re⁡{Aeiϕ0eiωt}.y(t)=\operatorname{Re} \left\{A e^{i\phi_0}e^{i\omega t}\right\}.

The complex amplitude

A~=Aeiϕ0\widetilde A=Ae^{i\phi_0}

contains both amplitude and phase and is called a phasor in steady-state sinusoidal analysis. Its magnitude is AA, and its argument is ϕ0\phi_0. Some conventions use root-mean-square rather than peak amplitudes.

Phasors simplify calculations because differentiation becomes multiplication by iωi\omega when the time dependence is eiωte^{i\omega t}. A convention using e−iωte^{-i\omega t} reverses several signs but gives the same physical predictions when used consistently.

In alternating-current circuits, electrical impedance relates voltage and current phasors:

V~=ZI~.\widetilde V=Z\widetilde I.

The argument of ZZ is the voltage phase relative to the current. For ideal circuit elements:

  • A resistor has voltage and current in phase.
  • For a capacitor, current leads voltage by π/2\pi/2.
  • For an inductor, current lags voltage by π/2\pi/2.

For sinusoidal voltage and current, average electrical power is

P=VrmsIrmscos⁡θ,P=V_{\mathrm{rms}}I_{\mathrm{rms}}\cos\theta,

where θ\theta is their phase difference. Thus, voltage and current magnitudes alone do not determine the average power delivered.

Phase in nonsinusoidal signals

A general periodic waveform can be decomposed into sinusoidal components by Fourier analysis. Each component has its own amplitude and phase. The collection of component phases forms a phase spectrum, which helps determine the waveform’s shape.

A time delay τ\tau changes the phase of each angular-frequency component by

Δϕ(ω)=−ωτ.\Delta\phi(\omega)=-\omega\tau.

A constant phase shift applied to all positive-frequency components is therefore generally not equivalent to a constant time delay. They are interchangeable for a single sinusoid, but not for an arbitrary broadband signal.

For some nonstationary signals, an instantaneous phase can be defined through an analytic-signal representation,

z(t)=a(t)eiϕ(t),z(t)=a(t)e^{i\phi(t)},

constructed using the Hilbert transform. Its instantaneous angular frequency is dϕ/dtd\phi/dt. This representation is especially useful for suitably narrowband or single-component signals. For signals containing several independent oscillations, one instantaneous phase may not describe the signal meaningfully. Phase is undefined wherever the relevant complex amplitude is zero.

Measurement and applications

Phase is normally measured relative to another signal, a reference oscillator, or a second propagation path. Common methods include comparing zero crossings, mixing signals with a reference, measuring quadrature components, and recording interference fringes.

Phase unwrapping reconstructs a continuous phase from wrapped measurements. It requires assumptions about continuity or additional observations; noise, abrupt changes, and regions of low amplitude can make the reconstruction ambiguous.

Important applications include:

  • Optical metrology: Interferometers convert relative phase changes into measurements of displacement, surface shape, or refractive index. A change in optical path length ΔLopt\Delta L_{\mathrm{opt}} produces a phase-change magnitude 2πΔLopt/λ02\pi\Delta L_{\mathrm{opt}}/\lambda_0, where λ0\lambda_0 is the vacuum wavelength.
  • Communications: Phase modulation encodes information in changes to a carrier’s phase. Coherent receivers compare the incoming signal with a local reference.
  • Antenna and acoustic arrays: Controlled phase differences steer or reshape a combined radiation pattern.
  • Control systems: Frequency-dependent phase shifts affect how feedback changes system stability.
  • Magnetic resonance: Phase-sensitive detection is used in nuclear magnetic resonance and magnetic resonance imaging.
  • Crystallography: Measured diffraction intensities do not directly provide all phases of the scattered amplitudes, giving rise to the phase problem in X-ray crystallography.

Phase in quantum mechanics

In quantum mechanics, a wave function is generally complex. Multiplying an entire state by a constant global phase,

ψ⟶eiαψ,\psi\longrightarrow e^{i\alpha}\psi,

does not change its physical predictions. In particular, the probability density remains unchanged:

∣eiαψ∣2=∣ψ∣2.|e^{i\alpha}\psi|^2=|\psi|^2.

Relative phases between components of a quantum superposition, however, can affect interference and measurement probabilities. This distinction parallels the difference between choosing an arbitrary phase reference and changing the relationship between physical contributions.

Quantum phase is therefore not simply the position of a material particle within a mechanical oscillation. It is part of the mathematical structure of probability amplitudes, with observable consequences arising through relative phase relationships.

Historical development and terminology

Wave theories of light developed through the work of Christiaan Huygens, Thomas Young, and Augustin-Jean Fresnel. Young’s interference experiments and Fresnel’s mathematical treatment of diffraction helped establish the importance of relative wave phase. Nineteenth-century electromagnetic theory and alternating-current engineering further developed phase-based descriptions, including complex representations and phasor methods.

The word phase has several distinct scientific meanings. Wave phase specifies position within an oscillatory cycle. A thermodynamic phase is a physically distinct state of matter, and a phase transition is a transformation between such states. Neither meaning is the same as phase space, the space used to represent a system’s dynamical states.