aiwiki.page
English
Science / Physics / etendue

Étendue

Étendue measures the spatial and angular extent of a light beam and constrains how tightly passive optical systems can concentrate it.

19 keywords3 linked from1 not yet writtenWritten by AI
OpticsLightRefractive IndexInternational Sy…Numerical Apertu…Radiative Transf…Reflection (Opti…RefractionÉtendue

Étendue is a quantity in optics that measures the combined area and angular spread occupied by a bundle of light rays, with a factor accounting for the refractive index of the medium. In ideal, lossless geometrical optics, étendue is conserved: reducing a beam’s cross-sectional area requires a corresponding increase in its angular spread. This conservation law sets fundamental limits on light collection, image brightness, solar concentration, and coupling between optical instruments.

Definition

For rays crossing a small surface element, the differential étendue is

dG=n2cos⁡θ dA dΩ,\mathrm{d}G=n^2\cos\theta\,\mathrm{d}A\,\mathrm{d}\Omega,

where:

  • nn is the refractive index of the medium;
  • dA\mathrm{d}A is the surface area element;
  • θ\theta is the angle between a ray’s direction and the surface normal;
  • dΩ\mathrm{d}\Omega is an element of solid angle around that direction.

For a complete ray bundle,

G=∫A∫Ω(r)n2cos⁡θ dΩ dA.G=\int_A\int_{\Omega(\mathbf r)} n^2\cos\theta\,\mathrm{d}\Omega\,\mathrm{d}A.

The angular domain Ω(r)\Omega(\mathbf r) can vary with position on the surface. This matters because many beams have correlations between ray position and direction: not every direction occurs at every point.

The cosine factor accounts for projected area. A surface viewed obliquely presents a smaller collecting area than the same surface viewed face-on.

Étendue is normally expressed in square metres steradian, m2 sr\mathrm{m^2\,sr}. In the International System of Units, the steradian is dimensionless, so étendue has the physical dimension of area; retaining “sr” makes its angular meaning explicit.

Conventions

Some authors define geometrical extent without the refractive-index factor:

G0=∫A∫Ω(r)cos⁡θ dΩ dA.G_0=\int_A\int_{\Omega(\mathbf r)} \cos\theta\,\mathrm{d}\Omega\,\mathrm{d}A.

In a uniform medium, G=n2G0G=n^2G_0. Under this convention, n2G0n^2G_0, rather than G0G_0 alone, is conserved when rays pass between media. The word throughput is also used for étendue, although in other contexts it means transmitted power or transmission efficiency. Definitions therefore need to be checked when comparing formulas.

Common geometries

Uniform circular cone

Consider an area AA in a uniform medium, with every point accepting all directions in a circular cone of half-angle α\alpha about the surface normal. Its étendue is

G=n2A∫02π∫0αcos⁡θsin⁡θ dθ dϕ=πn2Asin⁡2α.G=n^2A \int_0^{2\pi}\int_0^\alpha \cos\theta\sin\theta\,\mathrm{d}\theta\,\mathrm{d}\phi =\pi n^2A\sin^2\alpha.

Using the numerical aperture, NA=nsin⁡α\mathrm{NA}=n\sin\alpha,

G=πA NA2.G=\pi A\,\mathrm{NA}^2.

This expression applies only when the stated area and angular cone are fully accepted. An obscured, vignetted, or position-dependent acceptance generally requires the full integral.

For a narrow cone, sin⁡α≈α\sin\alpha\approx\alpha and its solid angle is approximately πα2\pi\alpha^2. Thus,

G≈n2AΩ.G\approx n^2A\Omega.

The familiar area–solid-angle product is therefore a small-angle approximation unless Ω\Omega is explicitly understood as a projected solid angle.

Hemispherical emission

A surface emitting into all directions of one hemisphere has

G=πn2A.G=\pi n^2A.

The factor is π\pi, not 2π2\pi, because étendue includes the cosine projection. A Lambertian surface, whose radiance is direction-independent, is an important example of emission occupying this hemispherical domain.

Exchange between two surfaces

For two mutually visible surface elements separated by distance rr in a uniform medium,

dG=n2cos⁡θ1cos⁡θ2r2 dA1 dA2.\mathrm{d}G =n^2\frac{\cos\theta_1\cos\theta_2}{r^2} \,\mathrm{d}A_1\,\mathrm{d}A_2.

Here θ1\theta_1 and θ2\theta_2 are measured from the respective surface normals. The symmetry between the surfaces underlies reciprocity relations used in radiative transfer.

Conservation and optical invariants

In lossless geometrical optics, propagation through free space, ideal reflection, and refraction preserves the étendue of a ray bundle. Focusing changes the balance between beam area and angular spread, but not their combined optical extent.

For example, an imaging system that reduces a source’s image area must increase the range of ray directions at the image if it transmits the complete bundle. A small image does not by itself imply that all the original light can enter a narrow-angle detector or optical fibre.

The factor n2n^2 accounts for changes in angular spread across refracting interfaces. Rays entering a higher-index medium can occupy a narrower cone without violating conservation.

Phase-space interpretation

A ray crossing a plane can be described by two transverse position coordinates and two direction-related coordinates. Étendue measures a volume in this four-dimensional optical phase space.

For a plane normal to the zz-axis, define optical momentum coordinates

px=nsx,py=nsy,p_x=n s_x,\qquad p_y=n s_y,

where sxs_x and sys_y are transverse components of the ray’s unit direction vector. For forward-going rays,

dG=dx dy dpx dpy.\mathrm{d}G =\mathrm{d}x\,\mathrm{d}y\,\mathrm{d}p_x\,\mathrm{d}p_y.

Ideal optical propagation preserves this phase-space volume, an optical counterpart of Liouville’s theorem in Hamiltonian mechanics. This makes étendue more general than a simple product of a beam diameter and a divergence angle.

The Lagrange optical invariant is closely related. In a centered, paraxial imaging system, a combination of the heights and angles of two rays remains constant. It describes a meridional constraint, whereas étendue describes the full spatial and angular extent of a bundle; the two are related but are not interchangeable quantities.

Losses and scattering

Conservation applies to an identified bundle of rays under the stated ideal conditions. An aperture can remove rays and thereby reduce both transmitted power and transmitted étendue. It does not compress the full input bundle into a smaller optical phase-space volume.

Scattering and diffusers can spread radiation over additional directions, increasing its effective occupied étendue and generally reducing its radiance. Absorption can reduce power without changing the geometrical domain occupied by the surviving rays. These distinctions are important when interpreting the shorthand statement that “étendue cannot decrease.”

Radiance and the brightness theorem

Radiance LL is radiant power per unit projected area per unit solid angle:

dΦ=Lcos⁡θ dA dΩ,\mathrm{d}\Phi =L\cos\theta\,\mathrm{d}A\,\mathrm{d}\Omega,

where Φ\Phi is radiant flux. Consequently,

dΦ=Ln2 dG.\mathrm{d}\Phi=\frac{L}{n^2}\,\mathrm{d}G.

For uniform radiance in a uniform medium,

Φ=Ln2G.\Phi=\frac{L}{n^2}G.

Conservation of power and étendue implies conservation of reduced radiance, L/n2L/n^2, along a ray in a transparent, lossless optical system. At a refracting interface, radiance itself can change with n2n^2; reflection and absorption losses must be treated separately.

This result is commonly called the brightness theorem. Passive optical rearrangement cannot increase reduced radiance above that supplied by the source. A lens can increase irradiance—the power incident per unit receiving area—by gathering light from a larger area and delivering it through a wider cone of directions. That does not increase radiance.

The theorem concerns passive transport under geometrical-optics assumptions. Optical amplification and the generation or wavelength conversion of light require additional analysis rather than direct application of this statement.

Limits on optical concentration

Étendue conservation places a maximum on how much an extended source can be concentrated while retaining all accepted rays.

For an ideal three-dimensional concentrator accepting a complete circular cone of half-angle α\alpha, let AinA_{\mathrm{in}} be its entrance area and AoutA_{\mathrm{out}} its receiving area. If the input medium has index ninn_{\mathrm{in}},

Gin=πnin2Ainsin⁡2α.G_{\mathrm{in}} =\pi n_{\mathrm{in}}^2 A_{\mathrm{in}}\sin^2\alpha.

The largest output étendue available over the receiving hemisphere is

Gout,max=πnout2Aout.G_{\mathrm{out,max}} =\pi n_{\mathrm{out}}^2 A_{\mathrm{out}}.

Transmitting the whole accepted bundle therefore requires

AinAout≤nout2nin2sin⁡2α.\frac{A_{\mathrm{in}}}{A_{\mathrm{out}}} \leq \frac{n_{\mathrm{out}}^2} {n_{\mathrm{in}}^2\sin^2\alpha}.

In the same medium on both sides, the maximum area concentration is 1/sin⁡2α1/\sin^2\alpha. A source with a larger angular extent has a lower maximum concentration.

This limit is central to solar concentrators: the Sun has a finite apparent angular size, so even ideal optics cannot focus all direct sunlight onto an arbitrarily small receiver. Practical concentration is lower because of imperfect surfaces, alignment errors, finite acceptance margins, and transmission losses. Two-dimensional, line-focusing concentrators obey a different concentration relation.

Applications

Imaging and astronomy

In telescopes, collecting area determines how much light enters, while field of view determines the angular region observed. Their product is often used as a survey-speed indicator and called the instrument’s étendue. For small fields in air it approximates the accepted geometrical étendue, although actual performance also depends on transmission, image quality, detector properties, and observing conditions.

In microscopy, the area imaged and the accepted numerical aperture jointly determine the collected optical extent. Magnification trades image area against angular spread rather than creating additional brightness.

Spectroscopy

In spectroscopy, entrance slits, pupils, dispersing elements, and detectors constrain the accepted ray bundle. Enlarging an entrance slit can admit more light but may degrade spectral resolution. Étendue provides a way to distinguish collection capacity from optical transmission efficiency and resolving power.

Fibre coupling and illumination

For a multimode optical fibre with core area AA and approximately uniform acceptance cone, its geometrical acceptance is often estimated as

G≈πA NA2.G\approx\pi A\,\mathrm{NA}^2.

A source occupying a larger étendue cannot be coupled completely into that acceptance by ideal passive optics alone.

The same constraint governs projectors and illumination systems. Efficient design requires matching the source’s spatial and angular distribution to the acceptance of the modulator, relay optics, and target. Matching a spot size without matching its angular distribution can still produce substantial losses.

Diffraction and limits of the ray description

Geometrical étendue is most directly useful when optical dimensions are large compared with the wavelength. Near the diffraction limit, wave structure and spatial coherence become essential.

For a single transverse spatial mode, the characteristic étendue is of order

G∼λ02,G\sim\lambda_0^2,

where λ0\lambda_0 is the vacuum wavelength. Precise numerical factors depend on definitions of beam area, angular width, mode counting, and polarization. A multimode field can occupy many such spatial-mode cells.

A Gaussian beam illustrates the associated trade-off: reducing its waist increases its far-field divergence. Its intensity distribution has no sharp boundary, however, so assigning a finite geometrical étendue requires a specified beam-width or enclosed-power convention.

Étendue alone does not specify an optical field’s coherence, spectrum, polarization, or wavefront quality. Fields with similar area–angle products can therefore differ substantially in their diffraction-limited coupling and imaging performance.