The center of gravity is the point used to represent the combined action of gravitational forces on an extended body. In the approximately uniform gravitational field encountered near Earth’s surface, a body’s distributed weight produces the same total force and turning effect as a single force acting through its center of gravity. This makes the concept fundamental to balancing objects, designing vehicles and structures, analyzing human movement, and determining the stability of ships and aircraft.
In a uniform gravitational field, the center of gravity coincides with the center of mass, the position determined by the distribution of mass alone. The terms are therefore often interchangeable in elementary mechanics and practical engineering, but they are not universally equivalent. A substantially nonuniform gravitational field can make the effective point of application depend on the body’s orientation, and a single body-fixed center of gravity may not exist.
The concept connects the geometry of mass distribution with the mechanics of forces and moments. Its practical significance depends not only on where the point lies, but also on how gravity interacts with supports, suspension points, buoyancy, aerodynamic forces, and acceleration.
Physical definition and relation to the center of mass
An extended body experiences gravity throughout its volume. Each small mass element , at position , experiences a force
where is the local gravitational field. The resultant gravitational force is
Its turning effect about an origin , expressed as torque, is
A point can represent the gravitational loading only if a force acting there reproduces both quantities.
In a uniform field, is constant over the body, so
Defining
therefore gives
The entire gravitational loading is mechanically equivalent to a force acting through the center of mass. This is the precise basis for identifying the center of gravity with the center of mass in ordinary terrestrial calculations.
For a single fixed direction of gravity, torque measurements identify a line of action, rather than a unique point along that line. Moving the representative force upward or downward along its own line does not change its torque. The conventional center of gravity is the body-fixed point through which the lines of action pass as the body is placed in different orientations, under the uniform-field approximation. This distinction explains why balancing an object in one orientation generally does not determine all three coordinates of its center.
The center of mass is more general because its definition does not require a gravitational field. It remains meaningful in free fall and in space, where apparent weight may vanish. By contrast, “center of gravity” emphasizes how gravitational loading acts. Neither point must lie within material: the center of a uniform ring lies in its opening, and the common center of mass of separated components may lie between them. The point is a property of the whole mass distribution, not necessarily a location occupied by a particular particle.
Calculation from mass distributions and geometry
For discrete components in a uniform gravitational field, the center of gravity is obtained from the mass-weighted average
In Cartesian coordinates,
Each component may itself be an extended object, provided its position is represented by its own center of mass. This permits a complex assembly to be reduced to a manageable collection of subassemblies.
For example, masses of and kilograms located at and metre have
The result lies closer to the heavier mass. If the components experience the same gravitational acceleration, their weights can replace their masses in the weighted average because the common factor cancels. Combining weights measured under different gravitational conditions, however, does not generally reproduce a mass-weighted center.
For a continuous body with density ,
Corresponding line or surface integrals describe slender wires and thin sheets. When density is uniform, it cancels, and the calculation becomes one of geometry: the center of gravity coincides with the centroid of the occupied volume, area, or line. Symmetry often provides the answer without integration. A uniform sphere has its center of gravity at its geometric center, while a uniform triangular sheet has it at the intersection of its medians.
Different physical realizations of a similar shape need not have the same center. A uniform solid cone has its center on the axis one-quarter of its height from the base; a thin conical lateral shell has its center one-third of its height from the base. These differences arise because volume and surface area distribute mass differently along the axis. Likewise, a hollow sphere with uniform thickness remains centered by symmetry, whereas adding a dense internal component displaces the center toward that component.
Composite calculations can treat a removed region as a negative contribution to mass and first moment. A circular hole cut from an otherwise uniform plate therefore shifts the center away from the missing material. For changing loads, a useful relation is
when a component of mass moves within a system of unchanged total mass . This formula underlies many loading and trim calculations, although removing or adding material also changes the denominator and must be handled separately.
Experimental determination and measurement
The simplest experimental method uses suspension. When an object hangs freely from a point and comes to rest, its center of gravity lies vertically below that point, provided the suspension transmits no significant resisting moment. Otherwise, weight would exert a torque and the object would continue rotating. A plumb line attached at the suspension point establishes the vertical direction.
For a thin irregular plate, a line is marked downward from one suspension point, and the procedure is repeated from another. Their intersection locates the center of gravity in the plane of the plate. Additional suspensions provide a check on experimental error. If the plate is flexible or its contents shift between trials, the lines may fail to identify a single material point because the mass distribution has changed.
Three-dimensional objects require more complete spatial information. Each suspension gives a vertical line through the center in the suspended configuration; these lines must be expressed in coordinates fixed to the object. Measurements from multiple orientations can then determine the three coordinates. For large assemblies that cannot conveniently be suspended, support reactions usually offer a more practical alternative.
Consider a horizontal beam supported at and , carrying total weight . If the vertical reaction at the second support is , moment balance gives
The reaction at the first support supplies the remaining share of the load. Multiple scales beneath a vehicle or platform similarly determine horizontal center-of-gravity coordinates. If scale acts vertically at , then
These equations assume that all relevant external forces and support locations have been accounted for.
A level weighing normally cannot determine height: changing the center’s vertical position does not change the moments of parallel vertical forces about a horizontal reference plane. Height can instead be inferred by tilting the assembly through a known angle and observing the resulting change in support reactions. Such tests require attention to suspension deflection, tire deformation, movable liquids, and the geometry of the tilt.
Accurate measurement also depends on calibration of load cells, dimensional measurements, and a defined loading condition. Fuel quantity, attached equipment, moisture, and packaging may change the result. Reported coordinates therefore need an identified origin and axis convention, together with measurement uncertainty. A center-of-gravity location without its coordinate reference is not sufficient for an engineering calculation.
Static equilibrium, stability, and tipping
The center of gravity becomes especially useful in statics, where an object is in equilibrium only if both the resultant external force and the resultant external torque vanish:
For a stationary object resting on a level surface under gravity alone, the upward support forces must balance its weight. Their combined line of action must also align with the vertical line through the center of gravity.
The relevant geometric region is the support polygon, the convex hull of the effective contact points or contact areas. If the vertical projection of the center of gravity lies strictly inside this region, nonnegative vertical support reactions can ordinarily balance the weight. If the projection lies outside, gravity produces an overturning moment about an edge of the support region. At the boundary, the object reaches the idealized threshold of tipping, with reactions at other contacts potentially falling to zero.
A rectangular block illustrates the role of height. Suppose its center of gravity lies a height above the support plane and a horizontal distance inward from the edge about which it could tip. On an inclined plane tilted toward that edge, the limiting angle satisfies
assuming the block remains rigid and does not slide first. A lower center or wider base increases the limiting angle. Friction must be analyzed separately: insufficient friction can cause sliding before the center’s projection reaches the edge.
Stability is also described through potential energy. In a uniform field,
An equilibrium is stable against a permitted small displacement when that displacement raises the center of gravity and therefore increases potential energy. It is unstable when a displacement lowers the center. A suspended object normally settles with its center below the suspension point; an inverted configuration with the center directly above the pivot is unstable unless additional constraints or active control are present.
The geometric test has limits. Adhesion, bolts, cables, suction, or embedded foundations can transmit forces that a simple unfastened contact cannot. A clamped object may remain in equilibrium even when its center projects beyond its footprint. Conversely, a high-speed disturbance can overturn an object that initially satisfies the static criterion. Stability against tipping is therefore not an intrinsic consequence of center height alone: it depends on constraints, loading direction, available friction, and the energy or momentum of the disturbance.
Historical development
The mathematical study of centers of gravity grew from problems involving balances, levers, and the equilibrium of plane figures. Archimedes, active in the third century BCE, developed a systematic treatment in On the Equilibrium of Planes. The work relates balance to distances from a support and investigates centers of gravity of geometrical figures. Its methods established a close connection between the law of the lever and the determination of a body’s balance point.
The lever principle expresses the equality of opposing moments. For two weights at perpendicular distances and from a fulcrum, equilibrium requires
This relationship provides more than a rule for a simple machine: it allows several distributed weights to be replaced by an equivalent resultant. Archimedean geometry used such reasoning to establish centers for triangles, parallelograms, and other figures. In On Floating Bodies, Archimedes also connected weight, displacement, and the equilibrium of floating bodies.
These investigations preceded the modern distinction between mass and weight. Their immediate subject was the balancing action of heaviness, not a general inertial property defined independently of gravity. Medieval and Renaissance scholars continued to examine balances and centers of gravity as part of the science of weights. During the Renaissance, translations, commentaries, and new geometrical work extended the analysis of plane and solid figures.
Galileo Galilei studied centers of gravity of solids early in his career. Such work belonged to a broader mathematical tradition that treated mechanical questions through geometry. In the seventeenth century, new methods for calculating areas, volumes, and moments made increasingly complicated distributions tractable. Integral methods eventually provided the compact expressions now used for continuous bodies.
The framework changed further with Isaac Newton and the publication of the Principia in 1687. Newton’s laws of motion and universal gravitation made it possible to separate two questions: where a system’s mass is concentrated for translational dynamics, and how an external gravitational field acts across that system. In later classical mechanics, the center of mass became fundamental even when no weight was present, while the center of gravity remained especially useful in statics and engineering. Their routine identification near Earth’s surface reflects a highly successful approximation rather than an exact equivalence in every gravitational environment.
Structures, lifting equipment, and ground vehicles
In structural engineering, locating the center of gravity converts a distributed dead load into a resultant for suitable equilibrium calculations. A prefabricated wall panel, bridge segment, or machine assembly may contain materials of different densities and irregularly positioned attachments. Its geometric center is therefore not necessarily its balance point. The center’s position relative to bearings, lifting points, and foundations determines the moments those elements must resist.
Lifting operations illustrate the distinction between load weight and load stability. A freely suspended rigid load tends to orient itself so that its center of gravity lies below the effective suspension point. If the lifting arrangement initially places the center elsewhere, the load can rotate as it leaves its supports. Forces in individual slings depend on their angles and attachment geometry, not simply on dividing the total weight by the number of slings. Flexible rigging and moving contents introduce additional degrees of freedom.
A crane must be analyzed as a combined system comprising the crane, its counterweights, the lifted load, and any relevant attachments. The load creates an overturning moment that generally increases with horizontal working radius. Counterweights and support reactions supply opposing moments. Outriggers enlarge the support region, but the stability of the ground beneath them remains a separate constraint. A geometrically adequate support footprint does not prevent failure if a support settles or the soil cannot sustain its reaction.
For road vehicles, center-of-gravity height influences lateral load transfer and rollover tendency. In a simplified rigid vehicle with track width , a centered center of gravity at height , level ground, and lateral acceleration , the idealized wheel-lift threshold is
This relation follows by balancing the overturning moment against the restoring moment . Actual behavior also depends on suspension roll, tire deformation, road banking, load movement, and transient motion. A wheel striking a curb can produce a tripped rollover outside this simple model.
Longitudinal placement determines axle loads. Braking transfers load toward the front axle, while forward acceleration transfers load toward the rear; the magnitude depends partly on center height and wheelbase. The vehicle’s center does not need to move relative to the chassis for the support reactions to change. Cargo displacement, by contrast, genuinely changes the mass distribution. Tanks with partially filled liquids complicate both effects because sloshing can shift the instantaneous center and exert time-dependent forces on the vehicle.
Aircraft loading and spacecraft dynamics
Aircraft loading expresses center-of-gravity position relative to a defined datum. The basic calculation uses the moment of each item:
where is its weight and its signed distance, or arm, from the datum. Empty-aircraft structure, occupants, baggage, payload, and fuel contribute separately. Operational loading documents specify a permissible envelope rather than a single ideal position because acceptable balance depends on total weight and flight configuration.
For a conventional fixed-wing aircraft, longitudinal center-of-gravity position strongly affects pitch equilibrium and static stability. Aerodynamic forces on the wing, tail, and fuselage must balance both force and moment about the center. Moving the center forward generally increases the control or tail force needed to achieve a given trim condition; moving it aft generally reduces the margin of longitudinal static stability. The detailed effects depend on the aircraft’s configuration, including whether it uses a conventional tail, a canard, or another arrangement.
A useful measure is the static margin,
with positions measured aft along the same axis, denoting the neutral point and the mean aerodynamic chord. A positive value corresponds to a center of gravity ahead of the neutral point under the specified analysis conditions. Fuel consumption can move the center in either direction, depending on tank positions and the sequence in which fuel is used. Consequently, a loading condition can change during flight even when no payload is added or removed.
Rotary-wing aircraft have related but distinct balance requirements. In a helicopter, the rotor system must generate the forces and moments needed to maintain attitude and translational equilibrium. Fore-and-aft or lateral center-of-gravity offsets affect the control displacement required and can restrict the available control margin. The center’s relation to the rotor hub matters more directly than its relation to a fixed wing’s aerodynamic reference points.
For spacecraft, center of mass is usually the more precise term because orbital free fall does not eliminate gravity but does eliminate ordinary supported weight. Thruster forces directed away from the center generate torque as well as translation:
Propellant depletion, solar-array deployment, and moving mechanisms can shift the center and alter the moment of inertia. Gravity gradients can also orient an extended spacecraft, but that effect requires accounting for variations of the field across the vehicle rather than applying all gravity at one point.
Floating bodies and the center of buoyancy
A floating object is acted on by weight through its center of gravity and by buoyancy associated with the surrounding fluid. In a fluid at rest, the resultant buoyant force is vertically upward and passes through the center of buoyancy, the centroid of the displaced fluid volume. For a freely floating body in equilibrium, its magnitude equals the body’s weight. This is an application of Archimedes’ principle.
The centers of gravity and buoyancy need not coincide. What matters initially is whether their force lines balance and how those lines change when the body heels. For a surface-piercing vessel, heel changes the shape of the submerged volume, generally moving the center of buoyancy toward the more deeply immersed side. This shift can produce a restoring couple even when the center of gravity is above the center of buoyancy.
For small heel angles, the geometry is described by the transverse metacenter. In the usual small-angle construction, the vertical through the shifted center of buoyancy intersects the original upright centerline at this point. The distance from the center of gravity to the metacenter is the metacentric height, . Positive gives initial restoring stability; negative gives initial instability.
For a vessel heeled through a small angle , the righting moment is approximately
The metacentric radius is
where is the second moment of the waterplane area about the relevant heel axis and is the displaced volume. This second moment is a geometric property, not the mass moment of inertia. For larger angles, the actual righting arm must be determined from the changing hull geometry, giving . Initial metacentric height alone does not describe the full range of stability.
Movable liquids can reduce stability through the free-surface effect. When a partly filled tank heels, liquid redistributes, shifting its mass toward the lower side and creating an additional heeling moment. In small-angle calculations this is often represented as a virtual rise of the vessel’s center of gravity. The effect depends strongly on the tank’s free-surface geometry and is not simply proportional to the amount of liquid present.
A fully submerged rigid body has no changing waterplane in the same sense. With fixed displaced volume, its buoyancy center is fixed relative to the body. Having the center of gravity below the center of buoyancy produces a restoring couple when it tilts. This distinction explains why surface-vessel stability cannot be reduced to the common but incomplete rule that the center of gravity must always be below the center of buoyancy.
Human movement and biological mechanics
In biomechanics, the human body’s center of gravity is usually calculated as the center of mass in a uniform gravitational field. The body is treated as a collection of segments—such as the trunk, upper arms, forearms, thighs, and lower legs—whose masses and individual centers combine through a weighted average. Segment parameters may be estimated from anthropometric datasets or obtained from imaging and other measurements.
The whole-body center is not a fixed anatomical landmark. In quiet upright standing it is commonly located in the pelvic region, but its position varies with body proportions, posture, and the placement of the limbs. Raising both arms shifts it upward; leaning the trunk changes its horizontal position; carrying an external load changes the center of the combined body–load system. A single fixed percentage of standing height cannot describe all people and postures.
For quiet standing, the projection of the center of mass relative to the support region helps characterize balance. The feet define the available contact region, while muscles continually adjust forces and moments at the ankles, knees, hips, and trunk. The center of pressure, measured from the resultant ground-contact force, is not the same as the center of mass. Their positions are dynamically related: shifting the center of pressure changes the moment acting on the body and can accelerate its center of mass.
Walking and running are not sequences of purely static equilibria. During a step, the center-of-mass projection may lie outside the instantaneous support region without indicating an uncontrolled fall. Motion, momentum, foot placement, and active joint torques are essential to the balance process. In a simplified inverted-pendulum model of walking, the body’s center moves over a supporting leg, but real gait includes changing leg length, energy exchange, and multi-segment rotation.
Jumping provides a clear distinction between whole-body translation and movement of individual parts. Once airborne, and neglecting aerodynamic forces, the center of mass follows the projectile trajectory set by takeoff. Internal movements can change the arrangement and rotation of the limbs but cannot independently redirect that trajectory. In the Fosbury-flop high-jump technique, introduced to wide international attention by Dick Fosbury’s gold medal at the 1968 Olympic Games, arching the body allows different body segments to clear the bar at different times; the center-of-mass path need not pass as high as the highest parts of the body.
Similar principles apply to animals and robots. Long tails can alter mass distribution and assist rotational control, while leg placement changes the available support and contact forces. For dynamic locomotion, however, center-of-gravity location is only one descriptor. Angular momentum, actuator forces, contact timing, and the mechanical properties of limbs also determine whether motion remains controlled.
Nonuniform gravitational fields and the limits of a single point
The center-of-gravity approximation becomes more subtle when the gravitational field varies appreciably across a body. If all local forces remain parallel but their magnitudes vary, a representative point for a particular configuration can be defined by
where is the magnitude along the common force direction. This is a gravity-weighted position rather than a purely mass-weighted one. Its transverse coordinates determine the resultant’s line of action, while the coordinate along that line does not affect torque.
For an illustration, consider two equal masses separated vertically in a parallel field that weakens upward. The lower mass contributes slightly more weight, so the gravity-weighted point lies below the midpoint. Rotating the same assembly changes which mass elements experience the stronger field. Thus, even with parallel forces, the effective center need not remain fixed within the body as its orientation changes.
When field directions also vary, the net force and torque must be treated independently. Replacing the entire loading by a single force at requires
For nonzero , this is possible only if
Any torque component parallel to the resultant force cannot be produced by shifting that force’s line of action. A general gravitational loading therefore need not possess an exact single-point representation.
Near Earth’s surface, these complications are usually very small for ordinary objects. For a spherical gravitating source, , giving the approximate magnitude change across a small radial separation ,
Using Earth’s mean radius of approximately metres, a one-metre radial separation corresponds to a fractional change of about . Local geology and Earth’s rotation add further variations, but the uniform-field model remains highly effective for most everyday balance calculations.
Across larger systems, these differences generate tidal forces and gravity-gradient torques. An elongated orbiting body can experience a tendency to align with the local radial direction because its nearer and farther parts experience different gravitational accelerations. The translational motion of the center of mass and the rotational motion about it must then be analyzed together; applying only the total gravitational force at the center would omit the orienting torque.
In general relativity, gravity is described through spacetime geometry rather than a universal force field acting simultaneously across an extended body. There is no generally unique global center of gravity in an arbitrary curved spacetime. Definitions of a center of mass for extended relativistic systems require specified geometric and dynamical conventions. The familiar engineering center of gravity belongs primarily to Newtonian mechanics and its local, approximately uniform-field limit.