The Beer–Lambert law describes how a beam of light is attenuated as it passes through an absorbing material. In its common chemical form, it states that the absorbance of a sample is proportional to the concentration of the absorbing substance and the distance traveled through the sample. The law is a foundation of quantitative spectroscopy and analytical chemistry, allowing concentrations to be determined from measurements of transmitted light. Its linear form applies under conditions in which the absorbing species and their optical properties remain unchanged, and scattering and instrumental effects are negligible or appropriately accounted for.
Mathematical statement
For monochromatic light passing through a homogeneous solution containing one absorbing species,
where:
- is the absorbance at wavelength ;
- is the incident radiant intensity, or a corresponding reference intensity;
- is the transmitted intensity measured in the same optical geometry;
- is the molar absorption coefficient, also called molar absorptivity;
- is the molar concentration of the absorbing species;
- is the optical path length through the sample.
The subscript emphasizes that absorption usually depends strongly on wavelength. In practice, the reference measurement commonly uses a blank containing the same solvent and other background components as the sample.
The transmittance is
so that
Thus, absorbance increases linearly with concentration and path length, while transmitted intensity decreases exponentially. An absorbance of 1 corresponds to 10% transmission; an absorbance of 2 corresponds to 1% transmission. Absorbance is not the fraction of light absorbed: that fraction equals only when reflection, scattering, and other losses are absent.
Units and conventions
Absorbance is dimensionless because it is a logarithm of an intensity ratio. When concentration is expressed in and path length in centimetres, the molar absorption coefficient has units of . In the International System of Units, using and metres, its unit is .
A closely related exponential expression is
where is the Napierian absorption coefficient, with units of inverse length. The two conventions are connected by
Failure to distinguish natural-logarithm and base-10 conventions can introduce a factor of approximately 2.303. The term extinction coefficient is used differently across disciplines, so its definition and units must be specified.
Physical basis
The exponential law follows when each thin layer removes the same fraction of the light entering that layer. For a layer of thickness ,
Integrating for constant gives
At the microscopic level, an absorbing atom or molecule can be characterized by an absorption cross section , an effective area describing its probability of absorbing an incident photon. For independent absorbers with number density ,
This relation explains the proportionality between absorption and concentration. If is expressed in , then
where is the Avogadro constant.
The model assumes that the absorption coefficient does not change with the beam intensity. At sufficiently high intensity, depletion of absorbing states or other nonlinear optical processes can invalidate that assumption.
Nonuniform media and optical depth
If the absorption coefficient varies along the path, the more general form is
The integral
is called the optical depth. It is related to decadic absorbance by .
For a nonuniform solution whose molar absorption coefficient remains constant,
Consequently, a transmission measurement determines an integrated amount along the beam path rather than necessarily revealing the local concentration at each position.
Mixtures and additive absorbance
For a mixture of independently absorbing species,
Absorbances are additive because the separate exponential transmission factors multiply. This permits several substances to be quantified from measurements at multiple wavelengths when their spectra are sufficiently distinct.
The equation applies to the actual species present, not automatically to the total amount of a substance added. If substances react, associate, or change protonation state, the mixture’s spectrum depends on both their individual absorption coefficients and their concentrations.
For example, an indicator may have differently absorbing protonated and deprotonated forms. Its measured absorbance therefore depends on pH through chemical equilibrium, even when its total analytical concentration is unchanged.
Experimental measurement
In spectrophotometry, a selected wavelength band passes through a sample held in a cell or cuvette. A detector measures transmitted light, and a reference measurement establishes the baseline. Solvent, cell material, path length, wavelength bandwidth, and detector response all affect the result.
For quantitative analysis, standards of known concentration are commonly used to construct a calibration curve:
Ideally, the slope equals and the intercept is zero after blank correction. In practice, a fitted intercept can account for a constant background offset, but it does not correct concentration-dependent departures from the law.
For example, if
then
This calculation presumes that the stated absorption coefficient applies to the wavelength, solvent, temperature, and chemical form used.
Measurement uncertainty
Because absorbance is calculated from a logarithm, uncertainty in transmission does not translate into constant absorbance uncertainty. For a small absolute uncertainty ,
At low absorbance, the difference between the blank and sample signals is small. At high absorbance, little light reaches the detector, making noise and stray light increasingly important. The useful measurement range therefore depends on the instrument and sample rather than on a universal absorbance cutoff. Concentration measurement uncertainty also includes contributions from calibration, path length, sample preparation, and the absorption coefficient.
Conditions and departures from linearity
Chemical changes and interactions
The relation requires a fixed absorption coefficient for the species being measured. Changes in temperature, solvent composition, or chemical environment can alter the spectrum.
At higher concentrations, interactions between molecules and changes in refractive index can make the effective molar absorption coefficient concentration-dependent. Association, dissociation, complex formation, and other reactions can also produce nonlinear relationships between absorbance and total concentration. Some apparent departures can be explained by applying the additive law to the individual chemical species.
Finite wavelength bandwidth
A practical instrument transmits a finite range of wavelengths rather than perfectly monochromatic light. If the absorption coefficient varies significantly across that range, the detector receives a weighted combination of different exponential transmissions. Taking the logarithm of their sum does not generally produce a quantity proportional to concentration.
Measurements near a broad absorption maximum often reduce this effect because the absorption coefficient changes relatively slowly with wavelength there.
Stray light and detector response
Stray light reaches the detector without undergoing the intended sample attenuation. At high absorbance, it can become a substantial fraction of the detected signal, causing measured absorbance to fall below the ideal prediction. Detector nonlinearity and imperfect baseline correction can introduce additional deviations.
Scattering, reflection, and emission
Scattering by particles or bubbles removes light from the direct beam without necessarily absorbing it. Reflection at interfaces can also reduce transmission. A measurement based solely on the loss of direct light may therefore report apparent absorbance rather than pure absorption.
In a scattering medium, the unscattered beam can still show exponential attenuation under suitable conditions, with an extinction coefficient that includes absorption and scattering losses. Light scattered back into the detector, however, makes the measured signal dependent on instrument geometry.
Fluorescence or other emission from the sample can add light to the detector and reduce the apparent absorbance. Strongly scattering or emitting media generally require a fuller radiative transfer treatment, which includes light entering and leaving each direction as well as absorption.
Applications
The Beer–Lambert law supports many forms of chemical and physical analysis:
- Solution analysis: determining concentrations of substances that absorb directly or form absorbing products in a controlled reaction.
- Biochemical measurements: estimating concentrations of proteins and nucleic acids, subject to their composition, purity, and measurement conditions.
- Reaction monitoring: following absorbance over time to study chemical kinetics.
- Gas spectroscopy: relating wavelength-dependent absorption to the amount of gas along a path; absorption coefficients depend on conditions such as temperature, pressure, and spectral line shape.
- Radiation attenuation: describing loss from a narrow, uncollided beam of X-rays or gamma rays, using attenuation coefficients appropriate to photon energy and material composition.
Transmission measurements alone do not uniquely identify the absorber. Substances with overlapping spectra can produce similar signals, so quantitative interpretation depends on chemical selectivity, spectral information, or independent constraints.
Historical development
The law combines several historically distinct results. Pierre Bouguer described the attenuation of light with path length in 1729. Johann Heinrich Lambert developed the exponential path-length relation in Photometria in 1760. August Beer investigated the dependence of absorption on the concentration of colored solutions in 1852.
The name “Beer–Lambert law” commonly refers to the combined concentration and path-length relationship, while “Beer–Lambert–Bouguer law” acknowledges Bouguer’s earlier contribution. “Beer’s law” often denotes the concentration proportionality specifically, although it is also widely used for the combined equation.