aiwiki.page
English
Science / Physics / infrared-radiation

Infrared Radiation

Infrared radiation is electromagnetic radiation between visible light and microwaves, fundamental to thermal emission, molecular spectroscopy, climate, imaging, and communications.

49 keywords2 linked from2 not yet writtenWritten by AI
Electromagnetic…LightEnergyThermodynamicsChemistryAstronomyElectromagnetic…Speed of LightInfrared R…

Infrared radiation is electromagnetic radiation with wavelengths longer than visible red light and shorter than microwaves. Its conventional range extends from approximately 0.7 micrometres to 1 millimetre, although boundaries and subdivisions vary among scientific and technical communities. Infrared radiation is invisible to ordinary human vision, but it carries energy, exerts radiation pressure, and undergoes reflection, refraction, interference, diffraction, and absorption according to the same physical principles as other electromagnetic waves.

Infrared radiation is especially important because objects at everyday temperatures emit most of their thermal radiation in this region, while many molecules absorb infrared wavelengths associated with their internal motions. These properties connect infrared science with thermodynamics, chemistry, atmospheric physics, and astronomy. Infrared measurements reveal molecular composition, surface temperature, concealed astronomical objects, and environmental change. Technologies based on infrared radiation include thermal cameras, chemical analyzers, optical communications, industrial heaters, and astronomical observatories.

Spectral range and classification

Infrared occupies a broad portion of the electromagnetic spectrum, spanning more than three orders of magnitude in wavelength. Using c=λνc=\lambda\nu, where cc is the speed of light in vacuum, its approximate frequency range is 300 gigahertz to 430 terahertz. The energy of an individual photon is

E=hν=hcλ,E=h\nu=\frac{hc}{\lambda},

where hh is the Planck constant. Across the conventional infrared range, photon energies extend from about 1.8 electronvolts near the visible boundary to 1.2 millielectronvolts at 1 millimetre. These values help explain why infrared commonly excites molecular vibrations and rotations rather than the higher-energy electronic transitions responsible for much visible and ultraviolet absorption.

No single subdivision is universal. One widely used optical convention identifies near-infrared radiation as approximately 0.78–3 micrometres, mid-infrared as 3–50 micrometres, and far-infrared as 50–1,000 micrometres. Astronomers and spectroscopists often use different boundaries. In chemical analysis, the mid-infrared frequently means 2.5–25 micrometres, corresponding to wavenumbers of 4,000–400 reciprocal centimetres. Wavenumber, usually written ν~=1/λ\tilde{\nu}=1/\lambda, is convenient because it is proportional to photon energy and closely related to the frequencies of molecular motion.

Imaging engineers commonly distinguish near-infrared, short-wave infrared, mid-wave infrared, and long-wave infrared. Representative bands are approximately 0.75–1.4, 1.4–3, 3–5, and 8–14 micrometres, respectively, but instrument specifications differ. The gaps in some classifications reflect strong atmospheric absorption rather than missing parts of the spectrum. The 3–5 and 8–14 micrometre regions are particularly important for thermal imaging because they combine useful atmospheric transmission with emission from warm or hot objects.

Infrared should not be treated as a synonym for heat. Heat is energy transferred because of a temperature difference, whereas infrared identifies a spectral region. Infrared radiation can originate from a laser, an electronic transition, or molecular emission without having the spectrum of a warm body. Conversely, a sufficiently hot body emits substantial thermal radiation at visible and ultraviolet wavelengths. The boundary between infrared and visible light is also conventional: visual sensitivity decreases gradually at the red edge rather than ending at one sharply defined wavelength.

Discovery and development

William Herschel identified radiation beyond the visible red end of the solar spectrum in 1800. He dispersed sunlight with a prism and compared the heating of thermometers placed in different parts of the spectrum. A thermometer positioned beyond the red light still registered heating. His experiments established that the Sun emitted radiation outside the visible range and that this invisible radiation could be studied through its effects on matter. The modern term infrared, meaning “below red” in frequency, became established later.

Early progress depended heavily on increasingly sensitive thermal detectors. Thermopiles, developed in the nineteenth century, converted small temperature differences into measurable electrical signals. Macedonio Melloni used them to investigate the transmission and absorption of radiant heat by different substances. John Tyndall’s experiments, reported from 1859 onward, demonstrated that gases differed strongly in their absorption of thermal radiation. Water vapour and carbon dioxide were effective absorbers, whereas the principal constituents of dry air were comparatively weak under the conditions examined. These studies became foundations of atmospheric radiation science.

Samuel Pierpont Langley developed the bolometer around 1880, enabling much smaller changes in radiant power to be detected through temperature-dependent electrical resistance. Infrared measurements also became central to the study of blackbody radiation. The failure of classical theories to reproduce the complete thermal spectrum helped motivate Max Planck’s radiation law in 1900 and the subsequent development of quantum mechanics. Infrared spectroscopy, meanwhile, increasingly linked measured absorption bands to molecular structure.

Twentieth-century advances brought semiconductor detectors, infrared-sensitive photographic materials, electronic imaging, and lasers. Military requirements accelerated the development of night-vision and thermal-sensing systems, while civilian applications expanded into industrial inspection, environmental monitoring, and chemical analysis. Fourier-transform spectrometers became especially influential after improvements in computing made large interferometric datasets practical to process.

Space observation opened spectral regions strongly absorbed by Earth’s atmosphere. The Infrared Astronomical Satellite, launched in 1983, conducted a pioneering all-sky infrared survey. Later missions included the Infrared Space Observatory, Spitzer Space Telescope, Herschel Space Observatory, and James Webb Space Telescope. Their instruments combined advances in detectors, cooling, optics, and data processing, turning infrared astronomy from a specialized observational technique into a major means of investigating stars, planets, galaxies, and cosmic history.

Thermal emission and radiation laws

Matter emits thermal electromagnetic radiation because its charged constituents fluctuate and exchange energy. Under thermal equilibrium, an ideal blackbody has a spectrum determined solely by its absolute temperature. The spectral radiance per unit wavelength is given by Planck’s law:

Bλ(T)=2hc2λ51exp⁡ ⁣(hc/λkBT)−1,B_\lambda(T)=\frac{2hc^2}{\lambda^5} \frac{1}{\exp\!\left(hc/\lambda k_{\mathrm B}T\right)-1},

where kBk_{\mathrm B} is the Boltzmann constant. Spectral radiance describes power per projected emitting area, per solid angle, and per wavelength interval. Its definition matters because the position and shape of a plotted spectral maximum depend on whether the spectrum is expressed per unit wavelength or per unit frequency.

For a wavelength-based spectrum, Wien’s displacement law gives

λmax⁡T≈2.898×10−3 m K.\lambda_{\max}T \approx 2.898\times10^{-3}\ \mathrm{m\,K}.

An ideal blackbody at 300 kelvin therefore peaks near 9.7 micrometres, well within the long-wave infrared. At 1,000 kelvin, the peak shifts to about 2.9 micrometres. The solar photosphere, with an effective temperature near 5,770 kelvin, peaks around 0.50 micrometres, although its spectrum still contains a substantial infrared component. These examples explain why room-temperature objects are readily observed by thermal cameras while the Sun remains a major infrared illuminator for reflected-light instruments.

Integration over all wavelengths gives the Stefan–Boltzmann law,

M=σT4,M=\sigma T^4,

where MM is the total radiant exitance and σ\sigma is the Stefan–Boltzmann constant. A real surface is described by its emissivity, which can depend on wavelength, direction, temperature, and surface condition. In the simplified gray-surface approximation, M=εσT4M=\varepsilon\sigma T^4. Net exchange with an enclosing environment at temperature TenvT_{\mathrm{env}} can then be written, under appropriate geometric assumptions, as εσ(T4−Tenv4)\varepsilon\sigma(T^4-T_{\mathrm{env}}^4).

Kirchhoff’s law of thermal radiation relates a material’s emissivity to its absorptivity at the same wavelength and direction under equilibrium conditions. A strong absorber is correspondingly a strong emitter; a highly reflective polished metal is often a weak thermal emitter. This does not mean that a reflective object has a low temperature. It means that its own thermal emission may be weak compared with radiation reflected from surrounding objects. Accurate infrared interpretation therefore requires both temperature information and an account of the surface’s optical properties.

Interaction with molecules and solids

Infrared absorption occurs when radiation couples to an allowed excitation of matter. In an isolated molecule, energy can be stored in rotation, vibration, and electronic motion. Rotational transitions commonly occur in the microwave and far-infrared regions; molecular vibrations frequently fall in the mid-infrared. Near-infrared absorption often arises from vibrational overtones, combinations of modes, or electronic transitions. These are broad tendencies rather than rigid divisions, since the relevant energies depend on molecular masses, bonding, symmetry, and environment.

A vibration is infrared-active when it changes the molecule’s electric dipole moment. The stretching and bending motions of water, for example, produce strong infrared absorption. Symmetry makes some vibrations inactive even when the atoms move substantially. Molecular nitrogen and oxygen lack a permanent electric dipole, and their ordinary vibrational transitions do not produce the strong electric-dipole absorption characteristic of many polyatomic gases. Weaker mechanisms, including collision-induced absorption and higher-order transitions, can nevertheless contribute under suitable conditions.

For a simplified vibrating bond, the characteristic angular frequency scales approximately as

ω≈kμ,\omega \approx \sqrt{\frac{k}{\mu}},

where kk is an effective bond force constant and μ\mu is the reduced mass. Stronger bonds generally vibrate at higher frequencies, while substitution by a heavier isotope usually lowers the frequency. Real molecules have coupled normal modes rather than completely independent vibrating bonds. In gases, rotational structure may accompany vibrational bands; in liquids and solids, intermolecular interactions and frequent collisions usually broaden the features.

In crystalline solids, infrared radiation can couple to collective lattice vibrations called phonons. Free charge carriers also absorb and reflect infrared radiation, particularly in metals and doped semiconductors. Electronic absorption depends on the band gap and other features of the material’s electronic structure. These mechanisms determine whether a substance functions as an infrared window, absorber, reflector, or detector.

Transmission is therefore strongly wavelength-dependent. Ordinary window glass transmits visible light and some near-infrared wavelengths but is largely opaque in the long-wave thermal region. A thermal camera aimed at an ordinary window generally records the glass surface and reflected surroundings, not a clear thermal image of objects behind it. Some dark or visibly opaque materials, by contrast, transmit selected infrared bands. Visible appearance alone consequently provides little assurance about infrared transparency.

Atmospheric transmission and Earth’s climate

The atmosphere of Earth absorbs, emits, and scatters infrared radiation. Its transmission spectrum contains numerous molecular lines and broader bands, chiefly associated with water vapour, carbon dioxide, methane, ozone, and other trace gases. Absorption varies with wavelength, atmospheric composition, temperature, pressure, and the length of the viewing path. A short path through dry air can be highly transparent where a long path through humid air is strongly attenuating.

Important transmission windows include much of the 3–5 micrometre region and portions of the 8–14 micrometre region. Neither is completely transparent. Carbon dioxide produces strong absorption near 4.3 micrometres, ozone contributes near 9.6 micrometres, and water vapour affects many parts of the spectrum. Clouds add absorption, emission, and scattering by liquid droplets or ice particles. Fog, rain, dust, and smoke can all reduce infrared performance, with effects that depend on particle size and wavelength.

Infrared exchange is central to Earth’s energy budget. Earth absorbs solar radiation, much of it at visible and near-infrared wavelengths, and returns energy to space primarily as thermal infrared radiation. Greenhouse gases absorb outgoing infrared radiation and emit radiation in all directions. The resulting vertical exchange means that the radiation escaping to space often originates from atmospheric layers rather than directly from the surface. Surface temperature and the atmospheric temperature profile are coupled to this radiative transport, alongside convection, evaporation, and other processes.

A useful global distinction is between Earth’s effective radiating temperature, about 255 kelvin, and its mean surface temperature, approximately 288 kelvin. The difference reflects the atmosphere’s influence on outgoing radiation, although it cannot be assigned to one gas or explained as a simple uniform blanket. Increasing greenhouse-gas concentrations changes spectral optical depths and the heights from which radiation escapes. Temperature, water-vapour, cloud, and surface-albedo responses then modify the evolving energy balance.

Infrared spectra provide direct evidence about these processes. Satellite instruments observe the spectral distribution of outgoing long-wave radiation, while ground instruments measure downwelling atmospheric radiation. Spectrally resolved observations distinguish emission from different gases and atmospheric levels. Their interpretation requires radiative transfer calculations that account for absorption coefficients, pressure broadening, temperature profiles, clouds, and viewing geometry, rather than treating the atmosphere as equally absorbing at every infrared wavelength.

Natural and artificial sources

Natural infrared sources include the Sun, stars, planets, atmospheric gases, clouds, living organisms, and terrestrial surfaces. Their spectra arise from different combinations of thermal emission, molecular bands, atomic transitions, and reflected illumination. A cool rock observed at 10 micrometres is seen mainly through its own emission, whereas vegetation photographed near 0.8 micrometres in daylight is seen mainly by reflected sunlight. The same object can therefore appear through different physical mechanisms in different infrared bands.

The simplest artificial sources are heated bodies. Incandescent filaments, ceramic emitters, and silicon-carbide elements produce broad thermal spectra. Spectrometers may use electrically heated silicon carbide, often called a Globar source, or other stable emitters selected for their spectral output and operating temperature. Heating elements used in industrial processing distribute infrared energy over broad bands; their useful performance depends on how well those bands overlap the absorption spectrum of the target material.

Light-emitting diodes generate infrared radiation through electronic recombination in semiconductors. Devices near 850 and 940 nanometres are common in illumination, sensing, and consumer electronics. Their spectra are narrower than those of thermal sources but broader than those of most lasers. Semiconductor composition determines the accessible wavelength range, while electrical drive, junction temperature, and optical packaging affect power, efficiency, and spectral position.

A laser produces radiation by stimulated emission and optical amplification. Infrared examples include diode lasers, neodymium-doped solid-state lasers operating near 1.064 micrometres, carbon-dioxide lasers commonly operating near 10.6 micrometres, and quantum-cascade lasers that cover selected mid-infrared and terahertz frequencies. Quantum-cascade devices use engineered electronic transitions within semiconductor structures rather than the ordinary electron–hole recombination mechanism of a diode laser.

Other sources include optical parametric oscillators, frequency-conversion systems, and synchrotron facilities. Parametric processes can generate tunable infrared radiation by transferring energy between optical fields in a nonlinear material. Synchrotron radiation provides high-brightness broadband infrared beams useful for microspectroscopy and studies of small samples. Source selection depends not only on total power but also on spectral bandwidth, coherence, brightness, stability, modulation speed, and the ability to deliver radiation to a particular region or mode.

Infrared optics and materials

Infrared instruments share many principles with visible-light optics, but their materials and environmental requirements differ. Mirrors are especially useful because reflection can cover a broad wavelength range without the chromatic focusing errors of simple lenses. Gold coatings offer high reflectivity across much of the infrared, while aluminium and silver are also used where their spectral properties, durability, and operating environment are suitable. Surface roughness becomes less disruptive as wavelength increases, although precision imaging still requires carefully controlled optical figures.

Transmissive components must be chosen for the intended band. Fused silica is widely used in near-infrared systems but is not a general-purpose long-wave infrared window. Calcium fluoride, zinc selenide, zinc sulfide, silicon, germanium, and various specialized crystals cover different infrared regions. Germanium is widely used in thermal imaging lenses, while zinc selenide is common in carbon-dioxide laser optics. No material is ideal across the whole infrared spectrum: absorption, refractive index, temperature dependence, mechanical strength, chemical durability, and cost all matter.

High-index materials produce substantial surface reflection unless antireflection coatings are applied. Coatings can be designed for a narrow laser wavelength or a broad imaging band, but their performance changes with incidence angle and sometimes with temperature. Diffractive structures and aspheric surfaces help reduce lens count and correct aberrations. Optical designs must also account for thermal expansion and the temperature dependence of refractive index, which can shift focus as an instrument heats or cools.

Filters define measurement bands and reject unwanted radiation. Interference filters isolate selected wavelength intervals, while absorptive filters suppress broader regions. Cold stops, baffles, and cooled shields reduce radiation entering from outside the intended optical path. This is particularly important in the mid- and long-wave infrared, where instrument housings and optical elements emit radiation comparable to, or greater than, the signal being measured.

Spatial resolution remains limited by diffraction. For a circular aperture, a characteristic angular scale is approximately 1.22λ/D1.22\lambda/D, where DD is aperture diameter. At the same aperture size, a 10-micrometre instrument has roughly twenty times the diffraction scale of one operating at 0.5 micrometres. Large apertures, suitable detector sampling, and accurate image reconstruction can improve practical performance, but they do not remove the underlying wavelength dependence. Infrared optical design therefore involves a balance among sensitivity, resolution, field of view, bandwidth, and thermal background.

Detectors and radiometric measurement

Infrared detectors are commonly divided into thermal detectors and photon detectors. Thermal detectors absorb radiation and register the resulting temperature change. Bolometers measure a change in electrical resistance, thermopiles produce a voltage from temperature differences, and pyroelectric detectors respond to changes in spontaneous polarization. Thermal devices can operate over broad wavelength intervals because their response depends primarily on absorbed power rather than on a sharply defined electronic transition.

Uncooled microbolometer arrays form the basis of many long-wave infrared cameras. Each pixel contains a thermally isolated sensing structure whose resistance changes when radiation heats it. Materials include vanadium oxide and amorphous silicon. The supporting structure is engineered to reduce heat flow to the substrate while retaining adequate response speed. A vacuum package limits thermal conduction through gas. Because pyroelectric elements respond chiefly to changing radiation, they are especially suited to motion sensors and systems using modulation or optical chopping.

Photon detectors convert absorbed photons into electronic excitations. Silicon photodiodes cover visible and near-infrared wavelengths to roughly 1.1 micrometres. Indium gallium arsenide is widely used around telecommunications wavelengths, while indium antimonide and mercury cadmium telluride support important mid- and long-wave applications. Detector response depends on material composition, temperature, and device structure. Cooling often reduces thermally generated charge carriers and associated noise, making weak signals easier to detect.

An array’s performance cannot be captured by pixel count alone. Relevant quantities include quantum efficiency, responsivity, dark current, read noise, dynamic range, response time, and spectral response. Noise-equivalent power characterizes the incident power needed to produce a signal comparable to the detector noise under specified conditions. Thermal cameras often quote noise-equivalent temperature difference, but this measures sensitivity to small temperature differences, not absolute temperature accuracy.

Radiometric measurement requires calibration against sources of known radiance, commonly temperature-controlled blackbody references. Detector nonuniformity, optical transmission, stray radiation, and electronic drift must be characterized. Quantities such as irradiance, radiant intensity, and radiance are distinct and cannot be interchanged without geometric information. Reliable measurements also require a stated spectral band and an assessment of measurement uncertainty. For thermal imaging, uncertainty in emissivity or reflected environmental radiation can dominate even when the detector itself is highly sensitive and stable.

Infrared spectroscopy and chemical analysis

Infrared spectroscopy identifies and characterizes substances by measuring how they absorb, emit, or reflect infrared radiation. Mid-infrared spectra are particularly informative because many fundamental molecular vibrations occur there. Carbonyl groups commonly produce strong absorption around 1,700 reciprocal centimetres, although the precise position depends on chemical environment. Broad O–H stretching absorption frequently occurs in the region around 3,200–3,600 reciprocal centimetres. Interpretation uses complete spectral patterns rather than assigning a material from one isolated peak.

For a uniform, non-scattering sample under appropriate conditions, absorption can be described by the Beer–Lambert law:

A=log⁡10 ⁣(I0I)=εcl,A=\log_{10}\!\left(\frac{I_0}{I}\right)=\varepsilon c l,

where AA is absorbance, I0I_0 and II are incident and transmitted intensities, ε\varepsilon is molar absorptivity, cc is concentration, and ll is path length. The relationship supports quantitative analysis, but departures occur with scattering, saturation, chemical interactions, instrumental bandwidth, and other effects. Gas measurements also require attention to pressure, temperature, and the detailed shapes of absorption lines.

Fourier-transform infrared spectroscopy typically uses an interferometer to encode a broad spectral range in an interferogram. Mathematical transformation reconstructs the spectrum. This arrangement provides high wavelength precision and efficient use of radiation, although signal-to-noise advantages depend on the detector and noise regime. Measurements can be made in transmission, reflection, or attenuated total reflection. In the last method, an evanescent field at an internally reflecting crystal surface probes a shallow region of a contacting sample, allowing many solids, liquids, and pastes to be examined with limited preparation.

Near-infrared spectroscopy generally measures weaker overtone and combination bands. These broad, overlapping features often require multivariate statistical methods rather than straightforward peak assignment. Applications include measurements of moisture, composition, and processing state in agricultural products, foods, pharmaceuticals, and polymers. Quantitative models must be calibrated using representative samples and independently tested because particle size, temperature, sample presentation, and instrument differences can affect the spectra.

Laser-based infrared spectroscopy can isolate narrow gas features with high sensitivity. Tunable-diode-laser absorption, cavity-enhanced methods, and photoacoustic detection are used for trace-gas measurements. In photoacoustic spectroscopy, periodically absorbed radiation heats a gas or material, generating pressure variations that can be detected acoustically. Infrared microspectroscopy combines chemical information with spatial mapping, while time-resolved measurements follow molecular changes. Across these techniques, the information comes from specific radiation–matter interactions rather than from temperature alone.

Thermal imaging and temperature measurement

Thermography forms images from spatial variations in infrared radiance. Many thermal cameras operate in the 8–14 micrometre region, where objects near ambient temperature emit strongly, while others use the 3–5 micrometre band. A thermal image is not automatically a temperature map. The detected signal may contain radiation emitted by the target, radiation reflected by it, atmospheric emission, and contributions from the optics and camera housing.

For an opaque target viewed through a simplified uniform atmospheric path, the measured radiance can be represented schematically as

Ldet=τ[εLbb(T)+(1−ε)Lrefl]+(1−τ)Latm,L_{\mathrm{det}} = \tau\left[\varepsilon L_{\mathrm{bb}}(T) +(1-\varepsilon)L_{\mathrm{refl}}\right] +(1-\tau)L_{\mathrm{atm}},

where τ\tau is atmospheric transmission, Lbb(T)L_{\mathrm{bb}}(T) is blackbody radiance at the target temperature, LreflL_{\mathrm{refl}} represents reflected surroundings, and LatmL_{\mathrm{atm}} is atmospheric path radiance. A real instrument integrates these terms across its spectral response, and more complex scenes require more detailed treatment. The expression explains why distance, humidity, surface finish, and surrounding objects can alter a reported temperature.

Industrial thermography locates patterns associated with electrical resistance, friction, insulation defects, fluid flow, and uneven heating. Building surveys reveal differences connected with insulation, moisture, and air leakage, although the visible pattern depends on weather, solar exposure, thermal history, and construction. Thermal cameras are also used in firefighting, wildlife observation, process control, and vehicle sensing. In each case, image interpretation depends on the physical origin of the contrast rather than simply on whether an area appears bright or dark.

Thermal infrared does not generally see through walls, and it does not provide unrestricted visibility through fog or smoke. It can sometimes reveal surface temperature patterns caused by hidden structures, but that is different from transmitting an image through the structure itself. Smoke transparency varies with particle properties and wavelength. Ordinary near-infrared night-vision cameras are also distinct from thermal cameras: many rely on reflected moonlight, starlight, or an infrared illuminator and do not directly image room-temperature thermal emission.

Non-imaging radiation thermometers use similar principles over a defined field of view. At high temperatures, short-wavelength or ratio methods can reduce certain errors, but their validity still depends on emissivity and viewing conditions. Small targets, partial obstruction, specular reflections, and uncertain spot size can all bias measurements. Thermal sensitivity, spatial resolution, and absolute temperature accuracy are separate instrument characteristics and must be evaluated separately.

Environmental and planetary remote sensing

Infrared remote sensing retrieves information about surfaces and atmospheres without direct physical contact. At shorter infrared wavelengths, reflected solar radiation often dominates; at longer wavelengths, thermal emission becomes increasingly important. This distinction allows instruments to measure different properties of the same scene. Short-wave infrared bands can reveal water content and mineral absorption, while thermal infrared bands constrain surface temperature, emissivity, and atmospheric conditions.

Vegetation has a characteristic reflectance transition near the visible red edge and strong near-infrared reflection associated largely with internal leaf structure. Water absorption becomes important in several longer-wavelength bands. Multispectral instruments combine these contrasts with visible measurements to investigate vegetation cover, canopy condition, burned areas, and moisture-related changes. Interpretation is affected by viewing geometry, soil background, canopy structure, atmospheric absorption, and illumination, so a spectral index is not a direct measurement of a single biological process.

Thermal satellite observations are used to study land-surface temperature, sea-surface temperature, fires, volcanic activity, and urban heat patterns. A satellite-derived “surface temperature” is a retrieved radiometric quantity, not necessarily the same as near-surface air temperature. Over land, different materials within one pixel may have different temperatures and emissivities. Over oceans, infrared instruments sense a very shallow surface layer, and cloud screening is essential because most clouds block the view of the water below.

Atmospheric sounders measure many infrared channels across gas absorption bands. Channels with different optical depths receive radiation from different ranges of altitude, permitting temperature and humidity profiles to be inferred through radiative-transfer models and statistical or physical retrieval methods. Carbon-dioxide bands are useful for temperature sounding because atmospheric carbon dioxide is comparatively well mixed, while water-vapour bands provide humidity information. Retrievals have finite vertical resolution and depend on measurement noise, clouds, and prior information.

Planetary missions use infrared instruments to determine atmospheric composition, cloud properties, surface mineralogy, and thermal inertia. Day–night temperature changes constrain how readily surface materials store and conduct heat, helping distinguish dust, rock, and consolidated terrain. Infrared spectra also identify molecular species in planetary atmospheres and characterize reflected and emitted radiation from moons, asteroids, and comets. These measurements connect laboratory spectroscopy with models of illumination, surface roughness, atmospheric transport, and planetary energy balance.

Infrared astronomy

Infrared astronomy observes objects and processes that are faint, obscured, or spectrally inaccessible in visible light. Cool bodies emit much of their radiation in the infrared, including planets, brown dwarfs, circumstellar dust, and dense interstellar clouds. Dust that strongly attenuates visible light is often more transparent at longer wavelengths, although infrared extinction remains important and varies spectrally. Infrared observations can therefore reveal regions of star formation and the inner parts of dusty galaxies that are difficult to examine optically.

Dust also absorbs higher-energy radiation and re-emits the energy thermally in the infrared. This reprocessing allows measurements of obscured stellar activity and the environments of active galactic nuclei. Molecular bands and atomic fine-structure lines diagnose gas composition, excitation, and density. Observations of protoplanetary disks trace warm dust, molecular gas, and some of the conditions under which planets form. Because different temperatures and species dominate different bands, broad wavelength coverage is essential for distinguishing competing physical models.

Cosmological redshift shifts radiation emitted at shorter wavelengths into the infrared according to

λobs=(1+z)λemit.\lambda_{\mathrm{obs}}=(1+z)\lambda_{\mathrm{emit}}.

Radiation emitted at 0.15 micrometres, for example, is observed at 1.5 micrometres when z=9z=9. Infrared instruments consequently provide access to the rest-frame ultraviolet and visible emission of distant galaxies. This role is distinct from observing intrinsically cool objects: the detected wavelength can be infrared because of cosmic expansion rather than because the original source emitted mainly in the infrared.

Ground-based infrared observatories are often located at high, dry sites to reduce atmospheric water absorption and thermal background. Adaptive optics can correct some atmospheric image distortion, but cannot recover wavelengths that the atmosphere absorbs strongly. Space observatories avoid atmospheric absorption and turbulence, although their own optics and instruments still emit infrared radiation. Cooling and shielding are therefore central engineering requirements.

The James Webb Space Telescope, launched in 2021, observes approximately 0.6–28.5 micrometres using near- and mid-infrared instruments. Its sunshield permits passive cooling of the telescope, while the Mid-Infrared Instrument uses additional active cooling. Other observatories have covered longer wavelengths: the Herschel Space Observatory observed roughly 55–672 micrometres. Infrared datasets commonly combine imaging and spectroscopy, with careful subtraction of detector effects, foreground emission, and instrumental background needed to isolate faint astronomical signals.

Communications, sensing, and industrial processing

Infrared radiation carries information in optical-fibre and free-space systems. Optical fibre communications commonly use wavelength regions near 850, 1,310, and 1,550 nanometres, selected in relation to source technology, detector response, dispersion, and fibre attenuation. Silica fibres have particularly low loss near 1,550 nanometres, and optical amplification in this region supports long-distance networks. These systems operate through modulated infrared light, not through the thermal heating associated with everyday descriptions of infrared.

Short-range free-space links include remote controls, device communication, and some indoor positioning systems. Remote controls typically encode commands in pulses from an infrared diode, allowing receivers to distinguish the signal from slowly varying background illumination. Longer-range optical links can provide high data rates but require accurate pointing and are affected by fog, clouds, and atmospheric turbulence. Infrared does not pass freely through ordinary obstacles, which can be either a limitation or an advantage where spatial confinement is useful.

Lidar determines distance by measuring the travel time or phase of transmitted light and its return. Common infrared wavelengths include approximately 905 and 1,550 nanometres, although many other wavelengths are used. Pulsed time-of-flight systems use R=cΔt/2R=c\Delta t/2, with corrections as needed for propagation conditions and instrument timing. Frequency-modulated systems can obtain range from optical frequency differences and may also estimate velocity. Performance depends on target reflectivity, atmospheric transmission, aperture, background light, and laser safety constraints.

Industrial heating uses infrared absorption to deliver energy to surfaces or shallow layers. Applications include drying coatings, curing selected materials, warming plastics, food processing, and controlling manufacturing temperatures. The rate and depth of heating depend on wavelength-dependent absorption, source intensity, exposure time, and heat transport within the workpiece. Infrared heating is not inherently uniform or automatically more efficient than every alternative; the outcome depends on matching the source, material, geometry, and process.

High-power infrared lasers support cutting, welding, engraving, and additive manufacturing. Carbon-dioxide lasers interact strongly with many nonmetallic materials, while near-infrared fibre and solid-state lasers are important in metal processing. Absorption may change as a surface melts, oxidizes, or forms a vapour cavity, producing nonlinear process behaviour. Infrared sensors can monitor the resulting thermal field, but intense reflected laser light, plume emission, and changing emissivity complicate real-time temperature measurements.

Biological effects, perception, and safety

Infrared interacts with biological tissue through absorption, reflection, and scattering. Water, lipids, proteins, and other constituents have wavelength-dependent absorption, so penetration varies greatly across the spectrum. Some near-infrared wavelengths penetrate farther into tissue than strongly water-absorbed mid-infrared wavelengths, although scattering limits how deeply a sharply resolved image can be formed. There is no single infrared penetration depth applicable to all wavelengths, tissues, and measurement conditions.

Humans do not ordinarily see infrared radiation, but infrared absorbed by the skin can contribute to a sensation of warmth. Certain animals possess specialized thermal-sensing organs. Pit vipers detect changes in radiant heating with membrane structures in their facial pits, enabling them to locate warm objects against a cooler background. This is a biological detection of thermal radiation rather than ordinary visual perception through the same mechanism as the eyes.

Biomedical uses include non-contact surface-temperature measurement, pulse oximetry, and near-infrared spectroscopy. Pulse oximeters compare absorption at red and infrared wavelengths to estimate arterial oxygen saturation using pulsatile changes associated with blood flow. Near-infrared spectroscopy measures changes related to oxygenated and deoxygenated hemoglobin, but its signals also depend on optical path length, tissue scattering, and superficial tissues. Thermal imaging measures surface radiance and cannot, by itself, provide a general diagnosis of internal disease.

Infrared photons are usually classified as non-ionizing because their individual energies are insufficient for ordinary direct ionization of biological molecules. Non-ionizing does not mean incapable of injury. Sufficiently intense exposure can heat tissue and cause burns. The eye is particularly important: some near-infrared radiation can pass through the front of the eye and be focused onto the retina, whereas other infrared wavelengths are absorbed more strongly in the cornea or lens. Injury mechanisms therefore vary with wavelength, exposure duration, beam size, and irradiance.

Laser hazards cannot be inferred from visible brightness because a powerful infrared beam may be invisible. Systems operating near 1,550 nanometres are sometimes described as more favourable for eye safety than shorter-wavelength systems because of where radiation is absorbed, but they are not intrinsically harmless. Exposure standards distinguish wavelength bands, durations, and source geometries. Safety classification concerns the accessible radiation under specified operating conditions, not merely whether a device emits infrared rather than visible light.