A voltmeter is an instrument that measures the difference in electric potential between two points, usually in an electrical circuit. Its reading is expressed in volts (V), the unit of potential difference in the International System of Units. A voltmeter is normally connected in parallel with the component or circuit section being measured. It ideally draws no current, although every practical instrument interacts with the circuit to some extent. Voltmeters may be dedicated instruments or functions within a multimeter, and may display results through a moving pointer or a numerical readout.
Measurement principle
Voltage describes the difference in electric potential between two locations. For a charge moving through a potential difference , the associated change in electrical potential energy is
A voltmeter therefore measures a difference, not an absolute potential at a single point. When an instrument displays the voltage at a circuit node, that reading is relative to another node, often designated ground or common. This reference need not be physically connected to Earth.
For direct-current measurements, the sign indicates polarity: a positive reading normally means that the potential at the positive input is higher than at the common input. For alternating-current measurements, the instrument generally reports a specified property of the varying voltage, such as its root-mean-square value, rather than its instantaneous value.
In circuits exposed to changing magnetic flux, induced voltages can make the arrangement of measurement leads significant. This follows from electromagnetic induction: the leads and circuit form a loop in which an additional voltage may be induced.
Connection and circuit loading
Unlike an instrument intended to measure electric current, a voltmeter is connected across two points rather than inserted in series with the circuit. Its input is designed to have a high electrical impedance, limiting the current drawn from the measured source.
For a steady DC measurement, the loading effect can often be represented using resistances. If a circuit has an open-circuit voltage and an equivalent source resistance , connecting a voltmeter of input resistance gives
The reading approaches the unloaded voltage when is much greater than . If the two resistances are comparable, the meter substantially changes the quantity being measured. For example, a 10-megohm voltmeter connected to a source with a 1-megohm source resistance reads about 90.9% of the open-circuit voltage.
Many general-purpose digital meters have an input resistance of about 10 megohms on their DC voltage ranges, although designs and ranges vary. Specialized instruments can have much higher input resistance. Conversely, some meters provide a deliberately low-impedance mode that suppresses misleading readings caused by weak capacitive coupling.
For time-varying signals, input capacitance also matters. A meter with high DC resistance can still load a high-frequency circuit appreciably through its input capacitance.
Main types
Moving-coil analog voltmeters
A traditional moving-coil voltmeter uses a galvanometer mechanism. Current through a coil in a magnetic field produces a torque, moving a pointer against a spring. Over its intended operating range, pointer deflection is approximately proportional to current.
A large series resistance converts the current-sensitive mechanism into a voltage-measuring instrument. By Ohm’s law, the total resistance needed for a selected full-scale voltage is
where is the full-scale voltage and is the movement’s full-scale current. The added resistance equals this total minus the movement’s own resistance.
Such meters are often characterized by sensitivity in ohms per volt:
Their input resistance consequently depends on the selected voltage range. Higher sensitivity means less loading at a given range.
A basic permanent-magnet moving-coil mechanism measures DC. AC measurement requires additional circuitry, commonly a rectifier. Analog displays make trends and fluctuations visually apparent, but their readings are affected by scale resolution, friction, orientation, and parallax.
Other electromechanical instruments
Moving-iron instruments use magnetic forces acting on soft iron and can operate on AC or DC. Their scales are generally nonlinear, and their response can depend on frequency and magnetic properties.
Electrodynamic instruments use interactions between current-carrying coils. Electrostatic voltmeters instead measure the force between charged electrodes. Electrostatic designs draw very little steady DC current and are useful for certain high-voltage measurements, although leakage and capacitance still affect performance.
Electronic analog voltmeters
Electronic analog voltmeters place an amplifier or buffer before the indicating mechanism. This separates the input impedance from the current needed to move the pointer, reducing circuit loading.
Vacuum-tube voltmeters were an important historical form; later instruments used transistor and other solid-state input stages. Electronic amplification also made much smaller voltages practical to measure.
Digital voltmeters
A digital voltmeter conditions the input signal and uses an analog-to-digital converter to produce a numerical result. Typical circuitry includes input protection, attenuation networks, amplification, a voltage reference, and control electronics.
Integrating converters are common in precision instruments because they can average noise over a measurement interval. Suitable integration periods strongly reject interference at power-line frequencies. Other converter architectures support faster readings or waveform sampling.
Digital meters may offer automatic range selection, data logging, computer interfaces, and statistical functions. Display resolution, however, is not the same as accuracy: additional digits are useful only when supported by sufficiently low noise, stable references, and controlled systematic errors.
Measuring alternating voltage
An AC voltage is not described completely by one number. Important quantities include peak voltage, peak-to-peak voltage, average value, frequency, and root-mean-square (RMS) voltage.
For a periodic voltage with period ,
RMS voltage corresponds to the DC voltage that would produce the same average heating power in an ideal resistor. For a sinusoidal waveform with peak amplitude ,
An average-responding, RMS-calibrated meter measures the average of a rectified signal and applies a scaling factor appropriate to a sine wave. It can therefore give incorrect RMS readings for distorted waveforms.
A true-RMS meter determines RMS by a method that does not assume a sinusoidal waveform. Its accuracy nevertheless remains limited by bandwidth, signal level, and crest factor—the ratio of peak amplitude to RMS value. Some AC modes reject the DC component and report only AC RMS; an AC-plus-DC mode includes both components. These measurements differ when a waveform has a DC offset.
Performance and measurement uncertainty
Important specifications include:
- Accuracy: the stated limits on deviation from the measured value under specified conditions, often expressed as a percentage of reading plus a range-dependent or display-count term.
- Resolution: the smallest change represented by the display on a selected range.
- Input impedance: the resistive and reactive loading presented to the circuit.
- Bandwidth: the frequency range over which specified measurement performance is maintained.
- Reading rate and settling time: how quickly valid measurements can follow changes.
- Common-mode rejection: the ability to reject voltage shared by both inputs relative to the instrument’s reference.
- Temperature stability and drift: changes in response with temperature or time.
The total measurement uncertainty also depends on the setup. Relevant effects include source loading, electrical noise, lead resistance in some configurations, leakage across insulation, and small thermoelectric voltages at junctions of dissimilar metals. At high frequencies, lead geometry and parasitic circuit elements become increasingly important.
Calibration establishes the relationship between readings and reference values, including associated uncertainties. Through metrological traceability, voltage measurements can be related to recognized standards. At the highest accuracy levels, voltage standards based on the Josephson effect provide a quantum-mechanical reference.
Development and applications
Voltmeters developed from nineteenth-century electrical indicating instruments. Sensitive current-detecting movements, combined with known resistances, enabled practical voltage measurement. Instruments designed for power systems subsequently expanded the range of measurable AC and DC voltages. Electronic amplification reduced loading, while digital conversion brought numerical displays, automation, and integration into computer-controlled measurement systems.
Applications include testing power supplies and batteries, examining electronic circuits, monitoring industrial processes, and measuring outputs from sensors that encode physical quantities as voltages. Panel voltmeters provide continuous indication within equipment, while laboratory instruments emphasize precision, stability, or automated acquisition.
A voltmeter usually reports a selected scalar quantity. An oscilloscope, by contrast, displays voltage as a function of time, revealing waveform shape, transients, and timing relationships that a single meter reading may conceal.
Operating limits and electrical safety
A voltage range describes measurement capability, not every aspect of safe operation. Safety ratings also account for insulation, input protection, transient overvoltages, and the electrical environment. Measurement-category ratings distinguish environments with different expected transient energies; instruments with the same nominal maximum voltage may therefore have different permitted applications.
Maximum voltage between input terminals can differ from the maximum voltage allowed between either terminal and Earth. Differential inputs and electrically isolated inputs are not equivalent, and communication connections may affect an instrument’s grounding.
High-voltage measurements often use specially rated probes or dividers. Their resistance, capacitance, insulation, and frequency response become part of the measurement system. An excessive input can damage the instrument, invalidate the reading, or create a shock or arc hazard even when the display itself remains within range.