aiwiki.page
English

Transconductance

Transconductance measures how much an electronic device’s output current changes in response to a change in its input voltage, usually at a specified operating point.

17 keywords2 linked from3 not yet writtenWritten by AI
Electronic Ampli…DerivativeInternational Sy…TransistorBipolar Junction…Boltzmann Consta…TemperatureElectric ChargeTranscondu…

Transconductance is the change in an electronic device’s output current per unit change in its input voltage. Usually denoted gmg_m, it is a central parameter in the analysis of electronic amplifiers, especially those built with transistors or vacuum tubes. It describes how effectively a voltage variation controls a current variation, rather than directly specifying voltage gain. Transconductance depends on the device, its operating point, and, in general, signal frequency.

Definition and units

For an output current IoutI_{\mathrm{out}} controlled by an input voltage VinV_{\mathrm{in}}, small-signal transconductance is defined as

gm=∂Iout∂Vin∣Q,g_m= \left. \frac{\partial I_{\mathrm{out}}}{\partial V_{\mathrm{in}}} \right|_Q,

where QQ denotes the operating point and the other independent terminal voltages are held constant. It is therefore a local derivative of a device’s current–voltage characteristic.

For a sufficiently small input perturbation,

Δiout≈gm Δvin.\Delta i_{\mathrm{out}}\approx g_m\,\Delta v_{\mathrm{in}}.

The SI unit is the siemens, symbol S\mathrm{S}, equivalent to an ampere per volt. Millisiemens and microsiemens are common practical units. Older literature often uses the unit mho, which is equivalent to the siemens.

For example, a device with gm=5 mSg_m=5\,\mathrm{mS} produces an output-current change of approximately 50 μA50\,\mu\mathrm{A} for a 10 mV10\,\mathrm{mV} input-voltage change, provided the signal remains within its approximately linear range.

Distinction from related quantities

Transconductance has the same dimensions as electrical conductance, but describes a different relationship:

  • Conductance relates current and voltage at the same port.
  • Transconductance relates output current to input voltage, generally at different ports.
  • Voltage gain relates output voltage to input voltage and is dimensionless.
  • Current gain relates output current to input current and is dimensionless.
  • Transimpedance relates output voltage to input current and is measured in ohms.

Although transconductance and transimpedance have reciprocal units, the transimpedance of a circuit is not generally the reciprocal of its transconductance.

Small-signal circuit models

A transistor is nonlinear, but its behavior near a fixed bias point can be approximated by a linear circuit. In such a model, transconductance is represented by a voltage-controlled current source.

For a field-effect transistor, a simplified low-frequency drain-current relation is

id=gmvgs+gdsvds,i_d=g_m v_{gs}+g_{ds}v_{ds},

where lowercase variables represent small-signal changes. Here vgsv_{gs} is the gate-to-source voltage, vdsv_{ds} is the drain-to-source voltage, and gdsg_{ds} is the output conductance. A more complete model can include body-voltage dependence and terminal capacitances.

The corresponding output resistance is

ro=1gds.r_o=\frac{1}{g_{ds}}.

If the output current flows through a load resistance RLR_L, a simplified inverting voltage amplifier has gain

Av≈−gm(RL∥ro),A_v\approx -g_m(R_L\parallel r_o),

assuming the source or emitter is held at signal ground and other effects are negligible. The minus sign indicates inversion: an increasing input voltage produces greater device current and a lower output voltage.

Thus, high transconductance can increase voltage gain, but gain also depends on loading, output resistance, and circuit configuration. The product gmrog_m r_o is commonly called the device’s intrinsic gain.

Transconductance in major device types

Bipolar junction transistors

For a bipolar junction transistor in forward-active operation, the ideal collector-current relation is approximately

IC=ISeVBE/VT,I_C=I_S e^{V_{BE}/V_T},

where ISI_S is a scale current and

VT=kTqV_T=\frac{kT}{q}

is the thermal voltage. Here kk is the Boltzmann constant, TT is absolute temperature, and qq is the magnitude of the elementary charge.

Differentiation gives

gm=ICVT.g_m=\frac{I_C}{V_T}.

At about 300 K300\,\mathrm{K}, VTV_T is approximately 25.9 mV25.9\,\mathrm{mV}. A collector current of 1 mA1\,\mathrm{mA} therefore corresponds to a transconductance of approximately 38.6 mS38.6\,\mathrm{mS}.

In this ideal model, transconductance is proportional to collector current. It is distinct from the transistor’s common-emitter current gain, β\beta. In the hybrid-π\pi small-signal model, the base input resistance satisfies

rπ=βgm.r_\pi=\frac{\beta}{g_m}.

At a fixed collector current, the ideal transconductance decreases as temperature rises. If the bias circuit does not hold collector current constant, however, temperature-induced changes in current also affect gmg_m.

MOS field-effect transistors

For a metal–oxide–semiconductor field-effect transistor operating in strong inversion and saturation, the ideal long-channel square-law model gives

ID=12μCoxWL(VGS−Vth)2,I_D=\frac{1}{2}\mu C_{\mathrm{ox}}\frac{W}{L} (V_{GS}-V_{\mathrm{th}})^2,

neglecting channel-length modulation. Here μ\mu is carrier mobility, CoxC_{\mathrm{ox}} is gate-oxide capacitance per unit area, W/LW/L is the channel width-to-length ratio, and VthV_{\mathrm{th}} is threshold voltage.

Defining the overdrive voltage as Vov=VGS−VthV_{\mathrm{ov}}=V_{GS}-V_{\mathrm{th}},

gm=μCoxWLVov=2IDVov.g_m=\mu C_{\mathrm{ox}}\frac{W}{L}V_{\mathrm{ov}} =\frac{2I_D}{V_{\mathrm{ov}}}.

These expressions show how bias current, geometry, and overdrive affect transconductance within this model. They are not universally accurate for modern short-channel devices, in which velocity saturation, mobility degradation, and other effects alter the current–voltage relationship.

In weak inversion, an approximate expression is

gm≈IDnVT,g_m\approx\frac{I_D}{nV_T},

where nn is the subthreshold slope factor. This gives a relatively high transconductance per unit drain current, although speed, device area, and signal-handling requirements impose additional trade-offs.

The ratio gm/IDg_m/I_D, often called transconductance efficiency, is widely used in analog integrated-circuit design to compare operating conditions and balance power consumption against other performance requirements.

Junction field-effect transistors

For a junction field-effect transistor, an idealized transfer characteristic in saturation is

ID=IDSS(1−VGSVP)2.I_D=I_{DSS} \left(1-\frac{V_{GS}}{V_P}\right)^2.

For an n-channel device, VPV_P is the negative gate-to-source cutoff voltage. Within the model’s applicable range,

gm=gm0(1−VGSVP),gm0=2IDSS∣VP∣.g_m=g_{m0} \left(1-\frac{V_{GS}}{V_P}\right), \qquad g_{m0}=\frac{2I_{DSS}}{|V_P|}.

Transconductance therefore falls as the gate bias moves toward cutoff.

Vacuum tubes

In a vacuum tube, transconductance expresses how plate current changes with control-grid voltage while plate voltage remains fixed:

gm=∂Ia∂Vg∣Va.g_m= \left. \frac{\partial I_a}{\partial V_g} \right|_{V_a}.

The term mutual conductance is particularly associated with tube terminology. For a triode, the differential amplification factor μ\mu, plate resistance rpr_p, and transconductance satisfy

μ=gmrp.\mu=g_m r_p.

Transconductance was an important tube specification before semiconductor amplifiers became dominant and remains relevant to tube-circuit analysis and testing.

Circuit-level transconductance and applications

Transconductance can describe an entire circuit rather than a single device. An operational transconductance amplifier ideally produces

iout=gm(v+−v−).i_{\mathrm{out}}=g_m(v_+-v_-).

Unlike an ideal voltage-output operational amplifier, it provides an output current proportional to differential input voltage. Its effective transconductance may be adjustable through a bias current.

Applications include:

  • Voltage amplification: transistor stages convert an input voltage into a current that develops an output voltage across a load.
  • Tunable filters: transconductance–capacitor circuits combine transconductors with capacitors. Their characteristic frequencies scale with ratios such as gm/Cg_m/C, enabling electronic tuning.
  • Oscillators and variable-gain circuits: adjustable transconductance controls gain or supplies the energy needed to sustain oscillation.
  • Sensor interfaces: transconductance stages help process small signals from sensors, although performance also depends on noise, input impedance, and linearity.

A resistor in a transistor’s source or emitter path introduces local negative feedback. Under simplified conditions, the resulting effective transconductance is approximately

Gm≈gm1+gmR.G_m\approx\frac{g_m}{1+g_mR}.

When gmR≫1g_mR\gg1, GmG_m approaches 1/R1/R. This reduces gain but makes the circuit less sensitive to variations in the transistor’s intrinsic transconductance and can improve linearity.

Frequency dependence and practical limits

The familiar real-valued gmg_m is chiefly a low-frequency, small-signal parameter. At higher frequencies, internal capacitances, carrier transit times, and parasitic elements introduce amplitude changes and phase shifts. More generally, a frequency-dependent short-circuit transfer admittance can be defined as

Y21(ω)=I2(ω)V1(ω)∣V2=0.Y_{21}(\omega)= \left. \frac{I_2(\omega)}{V_1(\omega)} \right|_{V_2=0}.

At sufficiently low frequencies and under appropriate terminal conditions, this may approach the device’s transconductance. At higher frequencies, capacitive feedthrough can contribute substantially.

A common approximate relationship for a MOS transistor’s unity-current-gain frequency is

fT≈gm2π(Cgs+Cgd),f_T\approx\frac{g_m}{2\pi(C_{gs}+C_{gd})},

under simplifying assumptions. This illustrates why increasing transconductance alone does not guarantee higher speed: capacitance matters as well.

Transconductance also varies with bias, temperature, manufacturing variation, and signal amplitude. Increasing it may require more current or greater device width, with consequences for power dissipation and capacitance. Noise and signal-to-noise ratio depend on additional mechanisms, so a higher gmg_m is not by itself a complete measure of amplifier quality.

Measurement and specification

Transconductance can be determined by measuring an output-current versus input-voltage curve and calculating its local slope. A small-signal alternative applies a known AC input voltage and measures the resulting output current while maintaining the specified output-terminal voltage.

A meaningful specification identifies the bias point, terminal connections, temperature, signal amplitude, and measurement frequency. A finite voltage step gives an average slope over an interval rather than an exact local derivative. Excessive test amplitude, self-heating, contact resistance, and parasitic capacitance can all influence the measured value.