Sorption is the uptake and retention of a substance by another material, encompassing adsorption at an interface, absorption into a material’s bulk, or both. The term is especially useful when the location or mechanism of uptake is unknown, mixed, or not important to the description. Sorption occurs in systems ranging from gases contacting porous solids to dissolved contaminants interacting with sediments. It is central to chemical separations, moisture control, pollutant transport, and the behavior of many natural and manufactured materials.
Terminology and scope
The material that takes up a substance is called the sorbent. The substance taken up is the sorbate, although terminology can distinguish the substance in the surrounding fluid from its sorbed state. Release from the sorbent is called desorption.
Adsorption and absorption describe different spatial distributions:
- Adsorption concentrates a substance at an interface, such as the boundary between a solid and a gas or between a solid and a liquid. Internal pore surfaces count as interfaces even when they lie deep inside a particle.
- Absorption incorporates a substance into the bulk of another phase. Examples include gas dissolving in a liquid and solvent entering a polymer.
- Combined sorption occurs when both mechanisms contribute, as when vapor adsorbs on a porous material’s surfaces while also dissolving in its organic components.
Sorption is not synonymous with every process that removes a substance from a fluid. Precipitation, chemical degradation, and mechanical filtration can also lower fluid concentrations. They must be distinguished from sorption when interpreting experiments, although reactive uptake can couple sorption to a chemical reaction.
Mechanisms and controlling factors
Sorption reflects interactions between the sorbate, the sorbent, and the surrounding medium. Its extent depends on the accessibility and affinity of uptake sites, the properties of the fluid, and the conditions under which the phases interact.
Surface interactions
Physical adsorption involves intermolecular interactions such as van der Waals forces, electrostatic attraction, and hydrogen bonding. Chemical adsorption involves stronger, chemically specific interactions with surface sites. These categories are useful but do not form a perfectly sharp division in all systems.
For charged substances, surface charge and fluid composition are particularly important. Changes in pH can alter both the charge of the surface and the chemical form of the sorbate. Dissolved salts can screen electrostatic interactions or compete for sites.
Ion exchange is a related uptake mechanism in which ions associated with a material are replaced by ions from the contacting fluid. It contributes to retention by clays, soils, and synthetic exchange resins. Surface complexation, in which dissolved species form complexes with surface functional groups, is another important mechanism.
Bulk partitioning and pore effects
A substance may distribute between a fluid and a sorbing phase by dissolving into that phase. This behavior is important for organic compounds entering polymers or the organic matter in soils and sediments. The hydrophobic effect can favor transfer of nonpolar compounds out of water and into less polar environments.
Porous materials offer large internal surface areas, but pore size and connectivity determine which molecules can enter and how rapidly they move. Narrow pores can enhance uptake through overlapping interactions with opposing pore walls. At higher vapor activities, condensation within pores may contribute substantially to measured uptake.
External conditions
Temperature, pressure, fluid composition, and competing substances all affect sorption. Physical adsorption is commonly exothermic, so its equilibrium extent often decreases with increasing temperature at fixed fluid activity. This is not a universal rule for all sorption: absorption, chemical reactions, changes in molecular speciation, and structural changes in the sorbent can produce different temperature dependencies.
Mixtures introduce competition and sometimes cooperative effects. A material with high capacity for a pure substance may show substantially different uptake when water vapor or other strongly interacting components are present.
Thermodynamic description
At chemical equilibrium, transfer of a component between communicating phases has no net thermodynamic driving force. Where the component can be treated as the same chemical species in both phases, equilibrium requires equality of its chemical potential:
For reactive sorption, equilibrium must also account for the stoichiometry and chemical potentials of the participating species and sites.
Chemical potential depends on thermodynamic activity, not simply concentration. Concentration and partial pressure often serve as practical approximations under sufficiently dilute or nearly ideal conditions.
The equilibrium amount taken up is described by a sorption isotherm: a relationship between uptake and the fluid-phase concentration, pressure, or activity at constant temperature. An equilibrium constant defined using activities and specified standard states can be related to the standard Gibbs energy change by
where is the gas constant and is absolute temperature. A fitted, dimensional sorption coefficient cannot be inserted into this expression without a consistent standard-state definition.
Common equilibrium models
Different models represent different assumptions or provide empirical descriptions over limited ranges.
Linear distribution
For dilute solutions, uptake is often approximated by
where is sorbed mass per unit mass of sorbent, is the equilibrium concentration in the contacting fluid, and is a distribution coefficient. If is expressed in milligrams per kilogram and in milligrams per litre, has units of litres per kilogram.
A constant can be useful over a restricted range, but it is not generally an intrinsic material constant. It can vary with concentration, pH, fluid composition, and the properties of the sorbent.
Langmuir model
The Langmuir isotherm is commonly written
Here is a limiting uptake and characterizes affinity. Its idealized assumptions include equivalent sites, a finite site population, and no interactions between adsorbed molecules. It predicts approximately linear uptake at low concentration and saturation at high concentration.
A good Langmuir fit does not by itself establish that these microscopic assumptions are correct.
Freundlich model
The Freundlich isotherm is an empirical relationship often written
The exponent convention varies; some treatments use instead. Values of the exponent between zero and one describe a decreasing slope as concentration increases. The model is widely used for heterogeneous environmental materials but does not predict a finite saturation capacity. Its parameters depend on the units chosen and the fitted concentration range.
Rates, transport, and hysteresis
Equilibrium capacity and uptake rate are distinct properties. A material may have a high equilibrium capacity yet take a long time to approach it. Sorption rates can be limited by:
- transport across the fluid layer surrounding a particle;
- diffusion through pores or through the sorbent matrix;
- binding or reaction at uptake sites;
- swelling or structural rearrangement of the material.
These processes can operate simultaneously. Fitting a simple rate equation to uptake data does not uniquely identify the rate-controlling mechanism.
Uptake and release may also follow different paths, a phenomenon called sorption hysteresis. Possible causes include pore filling and emptying behavior, structural changes, trapping in poorly accessible regions, and slow equilibration. An apparent hysteresis loop can therefore reflect either material behavior or insufficient experimental equilibration; it does not automatically demonstrate permanent binding.
Measurement and interpretation
In a common batch experiment, a known mass of sorbent contacts a fluid containing a known initial amount of sorbate. For a closed liquid system with constant volume and no other losses,
where and are the initial and equilibrium concentrations, is liquid volume, and is sorbent mass.
This calculation uses conservation of mass, but disappearance from solution is not sufficient evidence of sorption. Loss to vessel walls, volatilization, precipitation, degradation, and sampling can all bias the inferred uptake. Appropriate blanks, mass balances, and independent characterization help distinguish these processes.
Gas and vapor uptake can be measured through mass changes or changes in gas quantity. Flow-through experiments reveal breakthrough behavior and are especially relevant to operating filters and packed beds. Spectroscopy can help identify binding environments, while calorimetric measurements provide information about the heat associated with uptake.
Reported results depend on choices such as dry versus wet sorbent mass, pretreatment, equilibration time, and the operational separation of dissolved material from suspended particles.
Applications
Separation and treatment
Activated carbon and other porous sorbents remove selected organic compounds and gases from water and air. Ion-exchange materials separate dissolved ions, while moisture sorbents control humidity. Sorbent performance depends not only on capacity but also on selectivity, uptake rate, mechanical stability, and the possibility of regeneration.
Sorption also underlies many forms of chromatography, where different distributions between stationary and mobile phases produce different migration rates.
Environmental transport
Sorption influences how contaminants, nutrients, and trace elements move through soils, sediments, and groundwater. Strong retention can delay movement but does not necessarily destroy a contaminant or make it permanently unavailable.
For an idealized saturated porous medium with instantaneous, reversible, linear sorption, the retardation factor is
where is dry bulk density and is volumetric water content, equal to the water-filled porosity under saturation. Under these assumptions, the dissolved contaminant’s average transport velocity is the pore-water velocity divided by .
Nonlinear sorption, slow uptake, preferential flow, and mobile sorbing particles can invalidate this simple relationship.
Materials and storage
Water uptake affects the dimensions, stiffness, permeability, and durability of wood, textiles, polymers, and building materials. Gas sorption is also important in storage materials, sensors, and separation membranes. In each case, equilibrium uptake must be considered alongside transport rate, cycling stability, and the energy required to release the stored substance.
Limitations of sorption-based descriptions
“Sorption” is a useful inclusive term, but it does not specify a molecular mechanism. Similar uptake curves can result from different combinations of surface binding, bulk partitioning, reaction, and transport limitation. Mechanistic interpretation therefore requires evidence beyond an isotherm fit.
Likewise, removing a substance from a fluid transfers it to another phase rather than necessarily eliminating it. Spent sorbents, regeneration streams, and later desorption remain part of the material balance. Changes in temperature, fluid composition, or competing solutes can remobilize material that was retained under earlier conditions.