The Langmuir isotherm is a model of adsorption that relates the amount of a substance accumulated on a surface to its equilibrium pressure or concentration at a fixed temperature. It assumes a finite population of equivalent adsorption sites, each of which accommodates one adsorbing particle, with no interactions between particles occupying different sites. The resulting equation predicts an approximately linear increase in adsorption at low pressure or concentration and a limiting capacity when the sites become occupied. Introduced by Irving Langmuir in work published in 1918, it is a foundational model in surface science, heterogeneous catalysis, and the study of adsorption from gases and solutions.
Equation and parameters
For a gas adsorbing on a solid surface, the Langmuir equation is commonly written as
or, in terms of the amount adsorbed,
Here:
- is the fraction of adsorption sites occupied, or fractional coverage.
- is the equilibrium pressure of the adsorbing gas; for a component in a gas mixture, its partial pressure is used.
- is the equilibrium amount adsorbed, often expressed per unit mass of adsorbent.
- is the saturation capacity corresponding to complete occupation of the modeled sites.
- is an affinity parameter with units of inverse pressure.
For adsorption from a dilute solution, a common form is
where is the equilibrium concentration remaining in solution and has units reciprocal to those of . The subscript denotes equilibrium. Concentrations may be expressed as molar concentration or mass concentration, provided that the units of the parameters are consistent.
The concentration in this equation is the equilibrium concentration, not the initial concentration before adsorption. Likewise, is a fitted saturation capacity unless independent evidence establishes its microscopic interpretation.
At half coverage,
or, for the solution form, . A larger affinity parameter therefore means that half-saturation occurs at a lower pressure or concentration.
Physical assumptions
The ideal Langmuir model rests on several assumptions:
- A fixed number of sites. The surface contains a finite population of available adsorption sites.
- Equivalent sites. Each site has the same adsorption affinity.
- Single occupancy. Each site accommodates at most one adsorbing particle.
- Independent occupancy. Occupation of one site does not change the affinity of neighboring sites; lateral attractions, repulsions, and cooperative effects are absent.
- Reversible equilibrium. Adsorption and desorption balance at equilibrium.
- No additional adsorbed layers. The model does not include adsorption onto already adsorbed particles.
These assumptions define an idealized microscopic picture. Real surfaces may contain defects, several chemical environments, or pores of different sizes. Moreover, agreement with the equation does not by itself prove that adsorption occurs as a geometrically uniform monolayer.
Derivation from adsorption and desorption rates
A simple derivation uses chemical kinetics. Let represent a gas-phase particle and a vacant site:
For adsorption onto a single site without dissociation, assume that the adsorption rate is proportional to gas pressure and the fraction of vacant sites:
Assume also that the desorption rate is proportional to the occupied fraction:
At chemical equilibrium, the two rates are equal:
Rearranging gives
and therefore
The ratio follows from this particular kinetic formulation. Processes involving multiple sites, dissociation, or coverage-dependent rate coefficients can yield different expressions.
The equilibrium isotherm alone does not determine how rapidly equilibrium is reached. Transport through the surrounding fluid, pore diffusion, and surface reaction rates can control adsorption kinetics without appearing explicitly in the isotherm.
Thermodynamic interpretation
The same equation can be obtained through thermodynamics or statistical mechanics. For independent sites, the ideal configurational contribution to the adsorbed phase gives a chemical-potential dependence proportional to
where is the gas constant and is absolute temperature.
Equating the relevant chemical potentials of the adsorbed and fluid phases leads to
where is the dimensionless activity of the adsorbing species and is a dimensionless equilibrium constant defined using specified standard states. Thus,
For an ideal gas, , so . For a dilute solution approximated by , the concentration-based affinity parameter is . Nonideal systems require activity corrections rather than direct substitution of pressure or concentration.
This distinction matters when calculating a standard adsorption Gibbs free energy:
A dimensional fitted constant cannot be inserted directly into this logarithm without an explicit standard-state conversion.
The temperature dependence of the dimensionless equilibrium constant obeys the van ’t Hoff relation,
For exothermic adsorption, the equilibrium constant generally decreases as temperature increases. Experimental trends may be more complicated if the surface structure, solvent environment, or adsorption mechanism changes with temperature.
Limiting behavior
At low pressure, , the equation becomes
Adsorption is then proportional to pressure, a regime often described as Henry-law behavior. Only the product is well constrained by data confined to this region; the capacity and affinity cannot usually be estimated independently with precision.
At high pressure, ,
The plateau represents saturation of the modeled sites. The equation approaches saturation smoothly and contains no mechanism for multilayer growth, cooperative transitions, or capillary condensation.
Parameter estimation and experimental interpretation
The parameters are commonly obtained by fitting equilibrium adsorption measurements to the nonlinear equation. A traditional linear rearrangement for solution adsorption is
A plot of against therefore has an ideal slope of and intercept of . However, transforming the data changes the error structure and may give disproportionate influence to particular observations. Nonlinear fitting on the original measurement scale, with weighting appropriate to the experimental errors, generally provides a clearer basis for parameter estimation.
Important interpretive issues include:
- Incomplete saturation: without measurements approaching a plateau, may be largely extrapolated.
- Parameter correlation: different combinations of capacity and affinity can describe a restricted concentration range similarly well.
- Uncertain equilibrium: measurements taken before equilibration do not define an equilibrium isotherm.
- Indirect uptake measurements: calculating adsorption from initial and final solution concentrations requires an appropriate mass balance; precipitation, chemical transformation, or adsorption to the container can otherwise be mistaken for adsorption to the intended material.
- Changing chemical conditions: pH, ionic strength, and solvent composition may change both surface chemistry and the identity of the adsorbing species.
Fit quality should therefore be assessed through residuals, parameter uncertainty, and physical plausibility, rather than through a correlation coefficient alone.
Extensions and related models
Competitive adsorption
For several species competing for the same population of equivalent sites, the extended Langmuir equation is
The denominator accounts for competition: occupation by one species reduces the sites available to others. This expression assumes a common site population, one-site occupancy, and no lateral interactions. Species-dependent capacities or different molecular footprints require additional modeling care.
Dissociative adsorption
If a molecule dissociates and its fragments occupy two sites,
an ideal equilibrium treatment gives
and hence
where is defined consistently with the pressure convention. The changed pressure dependence reflects the different adsorption stoichiometry.
Heterogeneous and multilayer adsorption
The Freundlich isotherm is an empirical power-law relation frequently used for adsorption over heterogeneous surfaces, but it has no finite saturation capacity. Dual-site Langmuir models instead add contributions from two site populations with different capacities and affinities.
The Brunauer–Emmett–Teller theory extends an idealized adsorption treatment to multiple layers and is widely used in gas-adsorption measurements of specific surface area. It addresses behavior excluded from the single-layer Langmuir model.
Applications and limitations
The Langmuir isotherm provides a compact description of adsorption equilibria in gas separation, pollutant uptake, and chromatography. Its site-occupancy framework also underlies many expressions for catalytic reaction rates. An equivalent mathematical form describes independent one-to-one ligand binding to identical binding sites.
Its central limitation is that a simple saturating curve is not unique evidence for its assumed mechanism. Surface heterogeneity, pore filling, and several overlapping processes can produce approximately Langmuir-shaped data over a limited experimental range. A successful fit therefore establishes a useful description of the measured equilibrium behavior, but not necessarily the existence of identical, noninteracting adsorption sites.