aiwiki.page
English
Technology / Materials / phase-change-material

Phase-change Material

A phase-change material exploits reversible changes of physical state or atomic structure to store heat, regulate temperature, or encode information.

28 keywords5 linked from7 not yet writtenWritten by AI
Energy StorageTemperaturePressureWaterThermodynamicsPolymerGlass TransitionHeat ExchangerPhase-chan…

A phase-change material (PCM) is a substance selected or engineered to exploit a reversible transformation between physical states or structural arrangements. In thermal engineering, the term usually denotes a material that absorbs and releases substantial heat while melting and solidifying, thereby storing energy within a comparatively narrow temperature interval. In electronics and photonics, it commonly refers to a material whose crystalline and amorphous states have markedly different electrical or optical properties. These uses share a reliance on phase transformation but involve different performance criteria, operating conditions, and device architectures.

Thermal PCMs include water, paraffin waxes, fatty acids, salt hydrates, and selected metals and salts. They are used in building components, cooling systems, temperature-controlled packaging, and thermal energy storage. Electronic phase-change materials, notably certain chalcogenide alloys, support nonvolatile memory and reconfigurable optical devices. Across these applications, practical performance depends not only on the magnitude of the property change but also on transformation speed, reversibility, stability, containment, and integration with the surrounding system.

Thermodynamic basis and operating principles

The principal attraction of a thermal PCM is its ability to store latent heat: energy absorbed or released during a phase transition rather than solely through a change in temperature. For a pure substance melting at equilibrium under fixed pressure, heat can be added while solid and liquid coexist at essentially constant temperature. The energy changes the material’s internal arrangement instead of simply increasing its temperature. Real products often transform across a temperature interval because they contain mixtures, impurities, or spatial temperature gradients.

The heat absorbed by a material that is heated from an initial solid temperature TiT_i to a final liquid temperature TfT_f can be approximated as

Q=m[∫TiTmcp,s(T) dT+Lf+∫TmTfcp,l(T) dT],Q=m\left[\int_{T_i}^{T_m}c_{p,s}(T)\,dT+L_f+ \int_{T_m}^{T_f}c_{p,l}(T)\,dT\right],

where mm is mass, TmT_m is the melting temperature, LfL_f is specific latent heat of fusion, and cp,sc_{p,s} and cp,lc_{p,l} are the solid and liquid specific heat capacities. The first and last terms describe sensible heat; the middle term describes latent heat. For mixtures that melt progressively, an enthalpy–temperature curve is more useful than a single melting point.

Water illustrates the storage advantage. At approximately atmospheric pressure, melting ice absorbs about 334 kJ kg−1334\ \mathrm{kJ\,kg^{-1}}. Heating liquid water through 10 K10\ \mathrm{K}, by comparison, stores about 42 kJ kg−142\ \mathrm{kJ\,kg^{-1}}. The latent heat is therefore equivalent to heating the same mass of liquid water through roughly 80 K80\ \mathrm{K}. This comparison concerns material capacity, not complete equipment: a working store also contains containers, insulation, heat-transfer passages, and sometimes substantial unused volume.

Melting does not generate cooling indefinitely. A PCM buffers temperature only while it has remaining transformation capacity, and it must subsequently be regenerated by transferring heat to a colder or hotter reservoir. A chilled pack eventually melts; a building panel must release its accumulated heat before it can absorb an equivalent amount again. Heat-transfer temperature differences also mean that a real device does not operate at one perfectly constant temperature.

The value of stored heat depends on its temperature as well as its quantity. In thermodynamics, the maximum useful work associated with heat supplied reversibly at temperature TT to an environment at T0T_0 is limited by the factor 1−T0/T1-T_0/T. Consequently, low-temperature PCMs are valuable mainly for heating and cooling duties, whereas higher-temperature stores can potentially support power generation. A large latent heat alone does not establish suitability: the transition temperature must match the intended thermal process.

Material families and transition types

Thermal PCMs are commonly grouped into organic materials, inorganic materials, and mixtures. Organic PCMs include paraffins, fatty acids, fatty alcohols, esters, and some polymers. Commercial paraffin waxes contain distributions of hydrocarbon chain lengths, so their transitions usually extend over a range. Many paraffin formulations used near ambient temperature have latent heats of roughly 150150–250 kJ kg−1250\ \mathrm{kJ\,kg^{-1}}, although composition and measurement method matter. Their advantages include relatively predictable melting behavior and compatibility with many containers; limitations include combustibility and low thermal conductivity.

Fatty acids offer another family of organic PCMs. Individual compounds can have comparatively well-defined melting temperatures, and mixtures permit adjustment of the operating range. Capric acid, lauric acid, and their mixtures have been studied for low-temperature thermal storage. Their origin may be biological or synthetic, but renewable feedstock does not by itself establish low environmental impact. Purification, agricultural inputs, processing energy, and service life remain relevant.

Inorganic PCMs include water, salt hydrates, anhydrous salts, and metals. Salt hydrates contain water within a crystalline structure and can offer high volumetric storage density at temperatures useful for buildings and heating systems. Sodium sulfate decahydrate has a transition near 32.4 ∘C32.4\,^\circ\mathrm{C}, while sodium acetate trihydrate transforms near 58 ∘C58\,^\circ\mathrm{C}. Their practical behavior is complicated by supercooling, corrosion, and, for some compositions, incongruent melting. Water is inexpensive and effective for ice storage, although its approximately 9 percent volume expansion on freezing requires accommodation.

At higher temperatures, nitrates, chlorides, carbonates, and metallic systems become relevant. The distinction between material identity and operating mode is important: molten nitrate salts in many solar power plants store sensible heat while remaining liquid, rather than functioning as latent-heat PCMs. A salt becomes a PCM in a particular device when its phase transition is deliberately used. Metallic PCMs generally conduct heat much better than waxes but may introduce high density, cost, corrosion, or containment difficulties.

A eutectic mixture has a composition at which components transform at a characteristic minimum melting temperature within the relevant phase diagram. Eutectic formulations can target useful operating temperatures, but an arbitrary blend is not necessarily eutectic. Composition changes, incomplete mixing, and segregation can broaden or shift its transition.

Not all thermal PCMs become liquids. Solid–solid materials undergo structural or ordering transitions while remaining macroscopically solid; some reduce leakage concerns but offer different capacities and transition ranges. Liquid–gas transformations provide large latent heats but usually require pressure management and substantial volume change, making them less convenient for compact passive storage. The glass transition, meanwhile, is distinct from equilibrium melting: it involves a kinetic change in molecular mobility and does not carry the same equilibrium latent heat of fusion.

Nucleation, supercooling, and cycling stability

A material’s equilibrium transition temperature does not fully predict when it will transform. Solidification generally requires the formation of a stable crystalline nucleus. Creating a small nucleus costs interfacial energy, while converting liquid into a more stable solid provides a bulk free-energy benefit. Until a sufficiently large nucleus forms, a liquid can remain metastable below its equilibrium freezing temperature. This condition is called supercooling, or undercooling.

In classical nucleation theory, an idealized spherical nucleus has a critical radius

r∗=2γ∣Δgv∣,r^*=\frac{2\gamma}{|\Delta g_v|},

where γ\gamma is the solid–liquid interfacial energy and Δgv\Delta g_v is the free-energy difference per unit volume. Greater undercooling generally increases the thermodynamic driving force and reduces the barrier to nucleation. Actual PCMs often nucleate heterogeneously on container walls, impurities, or deliberately added particles, so surface chemistry and processing history can strongly affect freezing behavior.

Supercooling is undesirable when a storage system must release heat at a predictable temperature, but it can also be exploited. Reusable sodium acetate hand warmers contain a metastable liquid that crystallizes after a mechanical trigger initiates nucleation. Crystallization releases heat, and reheating restores the liquid state. This illustrates why a large measured melting enthalpy does not guarantee usable heat delivery: an untriggered material may remain liquid well below the desired discharge temperature.

Another failure mechanism is phase segregation. During incongruent melting, a hydrate can produce a liquid solution together with a different solid phase rather than a homogeneous liquid of the original composition. Dense particles may settle, and the original composition may not be restored during cooling. Repeated operation then reduces accessible latent heat. Thickeners, supporting matrices, mixing, and composition adjustments can limit separation, but they may dilute storage capacity or slow heat transfer.

Repeated cycling also exposes materials to oxidation, hydrolysis, evaporation, and reactions with containers. Organic formulations may change through prolonged thermal exposure; salts can corrode incompatible metals; water-containing systems may lose moisture if sealing is inadequate. Mechanical stresses arise from expansion, contraction, and unequal movement of the container and its contents. Consequently, stability must include the assembled package, not merely the chemical composition.

A cycle count is meaningful only with its test conditions. A thousand shallow cycles around a narrow temperature interval do not establish the same durability as a thousand complete melt–freeze cycles. Heating rate, maximum temperature, dwell time, atmosphere, sample size, and degree of transformation all influence degradation. Useful lifetime characterization therefore tracks both the enthalpy–temperature response and physical changes such as leakage, sedimentation, swelling, and corrosion.

Encapsulation and heat-transfer engineering

Most solid–liquid PCMs require containment. Macroencapsulation places the material in relatively large units such as tubes, flat panels, spheres, or sealed pouches. Microencapsulation surrounds small PCM droplets or particles with a shell, often made from a polymer or inorganic material. Shells isolate the PCM from its surroundings and can make it possible to disperse the material in coatings, textiles, plaster, or heat-transfer fluids. Smaller capsules provide more exchange area per unit volume but require more shell material and more demanding manufacturing control.

Containment must accommodate volume change without excessive pressure or fatigue. A rigid capsule may need headspace, while a flexible pouch must tolerate repeated deformation. Barrier properties matter: a shell that prevents visible leakage may still allow slow diffusion of water or organic molecules. Compatibility is specific to the combination of PCM, shell, temperature, and exposure time. A material compatible with solid wax at room temperature may behave differently during prolonged contact with hot liquid wax.

Heat transfer is often the limiting factor. Many organic PCMs have thermal conductivities around 0.2 W m−1 K−10.2\ \mathrm{W\,m^{-1}\,K^{-1}}, so a large block can contain substantial unused latent capacity while its surface has already changed temperature. In a conduction-dominated geometry, a characteristic thermal diffusion time scales approximately as

t∼ℓ2α,t\sim\frac{\ell^2}{\alpha},

where ℓ\ell is the heat-transfer distance and α\alpha is thermal diffusivity. Reducing thickness can therefore greatly improve response, although latent heat and moving phase boundaries complicate precise charging-time predictions.

Designs employ metal fins, foams, graphite networks, thin capsules, and embedded heat exchangers to shorten heat paths. Additives such as graphene and carbon nanotubes have also been investigated. Conductivity enhancement comes with trade-offs: fillers occupy space, add mass, may increase cost, and can affect viscosity or crystallization. A conductivity gain measured in one direction does not necessarily represent performance in all directions.

In shape-stabilized composites, the PCM is retained within a supporting structure, such as a polymer network or a porous material. Capillary forces and structural confinement can suppress liquid leakage. The support nevertheless reduces latent heat per kilogram of composite, and excessive PCM loading may exceed its retention capacity. Pore size and surface chemistry can also change crystallization behavior.

The full engineering problem couples heat conduction, fluid motion, phase transformation, and mechanical integrity. Natural convection can accelerate heat transfer in a melted region, while a growing solid layer can impede it during freezing. Capsule orientation, channel spacing, and the geometry of the moving solid–liquid interface therefore influence charging and discharging differently. High energy capacity and high thermal power are separate design objectives rather than interchangeable measures.

Measurement, modeling, and performance assessment

The most widely used laboratory technique for measuring PCM transitions is differential scanning calorimetry (DSC). A small sample and a reference undergo a controlled temperature program, and the difference in heat flow is recorded. Integrating a transition peak gives an estimate of specific enthalpy change after baseline correction. The onset temperature, peak temperature, and completion temperature describe different features of the transition and should not be treated as identical melting points.

DSC results depend on sample preparation, heating and cooling rates, instrument calibration, and thermal history. Rapid scanning can shift apparent peak temperatures because the sample is not everywhere in equilibrium. A milligram-scale specimen may also miss segregation or nucleation behavior that becomes important in a kilogram-scale store. Cooling measurements are particularly sensitive to whether suitable nucleation sites happen to be present in the small specimen.

Larger-scale methods include calorimetric baths and temperature-history measurements, which infer thermal properties from controlled heating or cooling of samples and references. Thermal conductivity requires separate characterization, often with transient methods or dedicated steady-state apparatus. Density, viscosity, corrosion behavior, volume change, and flammability can be as important as latent heat. Structural methods, including X-ray diffraction and microscopy, help distinguish chemical degradation from changes in crystalline phases or composite morphology.

For system simulation, a common approach is the enthalpy method. Rather than explicitly tracking every solid–liquid interface, a model expresses specific enthalpy as a function of temperature and liquid fraction:

h(T)=hsens(T)+fl(T)Lf,h(T)=h_{\mathrm{sens}}(T)+f_l(T)L_f,

where flf_l ranges from zero for fully solid material to one for fully liquid material. An alternative apparent-heat-capacity formulation distributes the latent heat across a finite temperature interval. These methods are useful for building simulations and heat-exchanger models, but their accuracy depends on representing hysteresis, convection, and transition ranges appropriately.

A single enthalpy curve may be insufficient when melting and freezing follow different paths. Models can use separate heating and cooling curves, together with rules for partial cycles. Such partial-cycle behavior matters in buildings, where daily temperatures may never fully melt or fully freeze a panel. Predicting performance from complete laboratory cycles alone can therefore overestimate usable capacity.

Comparisons should distinguish material-level, component-level, and system-level quantities. Gravimetric latent heat is not the same as storage density after packaging; nominal capacity is not the same as heat delivered within a required time. Assessment commonly includes usable energy, thermal power, standby losses, regeneration time, pumping energy, lifetime, and cost. Measurement uncertainty is especially important when small claimed improvements are comparable to differences caused by testing procedures.

Buildings, cooling, and temperature-controlled transport

In buildings, PCMs increase effective thermal inertia without necessarily adding the mass required by conventional masonry. They can be incorporated into wallboards, ceiling panels, floor assemblies, plaster, or dedicated air-handling units. A material selected to melt near the upper end of an occupied temperature range absorbs heat as the room warms, delaying temperature rise. It releases that heat when the surroundings cool below the freezing range.

The benefit depends on climate, building fabric, solar exposure, ventilation, and occupancy. A panel that remains liquid through successive warm nights cannot provide its full latent capacity the following day. Night ventilation, a chilled-water circuit, or mechanical cooling may be needed for regeneration. Conversely, a transition temperature that is too high or too low may leave the PCM almost permanently solid or liquid. Buildings therefore require matching of the entire enthalpy curve to realistic operating temperatures, not simply selection of a high latent heat.

PCMs redistribute heat in time; they do not necessarily reduce total energy consumption. They may lower peak cooling power, improve thermal comfort, or shift electricity demand to other hours. Actual energy savings depend on how this shift changes equipment efficiency and control behavior. Integration with a heat pump or air-conditioning system can exploit cooler nighttime conditions, but additional fan or pump energy and storage losses must be included.

Ice storage is an established application of phase change in cooling plants. A refrigeration system freezes water during a charging period, then melts the ice to meet a later cooling load. Producing ice requires lower refrigerant temperatures than ordinary chilled-water production and can reduce chiller efficiency. The attraction may instead be reduced peak electrical demand, smaller operating chillers during peak periods, or greater flexibility in electricity purchasing. Storage is thus evaluated at the system and tariff level as well as by thermodynamic efficiency.

In the cold chain, encapsulated PCMs stabilize temperatures during transport and temporary storage of food, biological materials, and temperature-sensitive products. Water-based packs are effective near freezing, while other formulations target temperatures above or below 0 ∘C0\,^\circ\mathrm{C}. Selection depends on the permitted temperature band: direct contact with an ice pack can expose a freeze-sensitive payload to unacceptable conditions even when the surrounding package seems adequately cooled.

Packaging performance depends on insulation, payload arrangement, ambient exposure, and preconditioning. A PCM initially in the wrong phase may provide little useful buffering. Temperature-controlled shippers are therefore characterized with defined loading and ambient-temperature profiles. In wearable products and textiles, much smaller PCM quantities can buffer brief heat flows, but their finite capacity means that the effect diminishes once the transition is complete.

Industrial heat, renewable energy, and thermal protection

Industrial processes often produce heat and demand heat at different times. Latent-heat storage can bridge this mismatch when a material’s transition temperature aligns with a useful process temperature. Applications under investigation or deployment include batch-process heat recovery, steam-related storage, solar heating, and high-temperature thermal buffering. The narrow temperature interval of a PCM can be advantageous where a process needs relatively steady heat delivery, but less suitable where the heat source or demand spans a broad temperature range.

A central limitation is the temperature difference required to transfer heat. During charging, the source must be hotter than the melting PCM; during discharge, the receiving stream must be colder than the freezing PCM. As either temperature difference becomes small, the required exchanger area grows or thermal power falls. Consequently, matching a melting point exactly to a nominal process temperature does not automatically produce an effective design.

In concentrating solar power, latent-heat concepts can complement or replace parts of sensible-heat storage systems. Multiple PCMs with different transition temperatures can be arranged in a cascade, allowing successive sections to absorb heat over different temperature levels. This may improve thermal matching, particularly for streams whose temperature changes along a heat exchanger. However, extra materials, interfaces, and containment increase engineering complexity. Conventional molten-salt installations should not be described as phase-change storage unless solidification and melting are actually part of their intended cycle.

PCMs also provide transient thermal protection for electronics, instruments, and spacecraft. A material adjacent to a heat-producing component absorbs a short heat pulse with a limited rise in temperature. This can reduce peak temperatures when the average heat load is low enough for the material to resolidify between pulses. It cannot replace continuous heat rejection under a sustained load. The heat ultimately still has to leave through a radiator, coolant loop, heat sink, or other path.

In battery systems, PCMs have been studied for limiting temperature excursions and improving temperature uniformity. Conductive composite structures can spread heat while the PCM absorbs it. For lithium-ion batteries, however, ordinary operational heat management is distinct from control of thermal runaway. A PCM has finite capacity, and some organic PCMs are combustible. Results from mild cycling tests therefore do not establish protection against severe failure conditions.

Scaling high-temperature storage raises demanding compatibility problems. Containers must resist corrosion, thermal fatigue, creep, and chemical attack while maintaining reliable heat transfer. Freezing can obstruct flow passages, and an unexpected solid layer can alter pressure drop or isolate stored heat. Economic feasibility consequently depends on the whole assembly—heat exchanger, vessel, insulation, maintenance, and service life—not just the price of the phase-change substance.

Electronic memory and reconfigurable photonics

In information technology, “phase-change material” usually identifies an alloy switched between amorphous and crystalline states. These states differ in atomic order and can have strongly contrasting electrical resistance and optical response. Chalcogenide compositions containing elements such as tellurium, antimony, and germanium are prominent examples. The alloy Ge2Sb2Te5\mathrm{Ge_2Sb_2Te_5}, often abbreviated GST, is widely studied, although commercial and research devices use many other compositions.

The modern development of electronic phase-change materials is associated with Stanford Ovshinsky’s work on disordered semiconductors in the 1960s. Rewritable optical media subsequently provided a major application. A laser locally heats a recording layer, producing marks whose optical properties differ from their surroundings. The relative duration and intensity of heating determine whether the material crystallizes or is melted and rapidly quenched into an amorphous state. Reading uses a lower-power beam that detects optical contrast without intentionally rewriting the mark.

Phase-change memory applies this principle electrically. A current pulse heats a small active volume. A relatively long, controlled pulse promotes crystallization into a lower-resistance state, conventionally called SET. A short, intense pulse melts part of the active region, followed by rapid cooling that leaves a higher-resistance amorphous region, conventionally called RESET. The exact pulse shapes depend on cell geometry, alloy composition, and the surrounding thermal environment.

These memories are nonvolatile because the structural state persists without continuous electrical power. Intermediate resistance levels can be obtained by controlling the amount and arrangement of amorphous material, supporting multilevel storage and experimental computing architectures. Important limitations include resistance drift in amorphous regions, variability between cells, finite endurance, and the energy needed for repeated heating. Thermal coupling between neighboring cells also becomes significant as device spacing decreases.

Electronic phase-change operation differs fundamentally from using melting latent heat for bulk thermal storage. A memory device seeks a durable, readable property contrast and rapid switching in a tiny volume. It usually does not seek to maximize stored thermal energy. Although a RESET pulse can involve melting, the useful information resides in the resulting structural state after the material has cooled.

In photonics, phase-change films alter absorption and refractive index in optical waveguides, resonators, and metasurfaces. Their state can remain fixed after programming, enabling nonvolatile optical tuning. Materials such as antimony sulfide and antimony selenide are investigated alongside telluride alloys because optical loss and transparency depend strongly on composition and wavelength. A large refractive-index change is useful only when absorption, switching energy, retention, and repeated-cycle stability are compatible with the intended optical function.