The Otto cycle is an idealized thermodynamic cycle used to analyze the conversion of heat into mechanical work in spark-ignition internal combustion engines. It consists of four processes: isentropic compression, constant-volume heat addition, isentropic expansion, and constant-volume heat rejection. Named after the German engineer Nikolaus August Otto, it provides a simplified model for gasoline engines and other engines in which an externally initiated flame burns a compressed fuel–air mixture. The ideal cycle is distinct from the mechanical sequence of intake, compression, power, and exhaust in a four-stroke engine.
Historical development
In 1862, the French engineer Alphonse Beau de Rochas described principles for an engine operating through intake, compression, combustion and expansion, and exhaust. In 1876, Otto developed a successful four-stroke engine using compression before ignition, a major step in the practical development of internal combustion engines.
The thermodynamic cycle bearing Otto’s name abstracts the compression, heat release, expansion, and energy rejection of such engines into a closed sequence of ideal processes. The name therefore refers both to a historical engine tradition and, more precisely in thermodynamic analysis, to a mathematical model. The ideal Otto cycle is not a complete description of any particular engine’s valve timing, combustion process, or gas exchange.
Assumptions of the ideal model
The standard air-standard Otto cycle replaces the actual engine gases with a fixed mass of air circulating in a closed thermodynamic system. Its principal assumptions are:
- The working fluid behaves as an ideal gas.
- Compression and expansion are internally reversible adiabatic processes, so their entropy remains constant.
- Fuel burning is replaced by external heat addition at constant volume.
- Exhaust and replacement of the gases are replaced by heat rejection at constant volume.
- Mechanical friction, leakage, and pressure losses are neglected.
An additional cold-air-standard assumption treats the specific heat capacities as constant, commonly evaluated near ambient temperature. This produces the familiar closed-form expression for efficiency. An air-standard model can instead use temperature-dependent heat capacities, in which case that simple expression does not apply exactly.
The heat-addition step is an abstraction of combustion, not a claim that fuel burning in a real engine is an external heating process.
The four processes
Let the four states be numbered in their order around the cycle. Write for pressure, for volume, and for absolute temperature. States 1 and 4 occur at the maximum volume, while states 2 and 3 occur at the minimum volume.
1–2: Isentropic compression
The working gas is compressed from its maximum to its minimum volume. Work is done on the gas, increasing its temperature and pressure. With constant heat capacities,
where
is the ratio of constant-pressure to constant-volume specific heat capacity.
Define the compression ratio as
The state relations are then
In a reciprocating engine, the geometric compression ratio equals the cylinder volume at bottom dead center divided by its volume at top dead center.
2–3: Constant-volume heat addition
Heat is added while the volume remains fixed:
Both temperature and pressure increase. Because there is no volume change, the boundary work is zero. Under the constant-specific-heat assumption, heat input per unit mass is
This idealization represents rapid heat release near the end of compression, when piston movement during combustion is relatively small. Real combustion takes a finite time and normally extends over a range of cylinder volumes.
3–4: Isentropic expansion
The hot gas expands back to the maximum volume, doing work on the piston. Its temperature and pressure fall. Since the expansion ratio equals the compression ratio,
This expansion corresponds approximately to the power-producing part of an engine’s operation.
4–1: Constant-volume heat rejection
Heat is rejected at the maximum volume, restoring the initial state:
The positive magnitude of heat rejected per unit mass is
In an actual engine, exhaust discharge and replacement by fresh charge help restore the cylinder conditions for the next cycle; the same trapped gas does not simply cool at constant volume.
Work and thermal efficiency
By the first law of thermodynamics, the net change in internal energy over a complete cycle is zero. Consequently, the net work output per unit mass is
The thermal efficiency is
Because both isentropic processes have the same volume ratio,
Substitution gives the cold-air-standard result:
This equation shows that ideal efficiency increases with compression ratio and with the specific-heat ratio. Under these assumptions, efficiency does not depend explicitly on the amount of heat added. Nevertheless, heat input affects temperatures, pressures, and work output; equal efficiency does not imply equal power or equal mechanical loading.
For example, with and ,
The resulting efficiency of about 60% is a prediction of the ideal model, not a representative measured efficiency for every gasoline engine with that compression ratio.
Thermodynamic diagrams
On a pressure–volume diagram, the two constant-volume processes appear as vertical lines, joined by curved compression and expansion paths. For the usual heat-engine direction, the cycle runs clockwise, and the enclosed area represents net work:
On a temperature–entropy diagram, the isentropic processes appear as vertical lines. The constant-volume heat-addition and heat-rejection paths connect them. For the internally reversible model, heat transfer satisfies
so the enclosed area also represents net heat input, equal to net work output over the cycle.
Relationship to real engines
Thermodynamic processes versus piston strokes
The four processes of the Otto cycle should not be identified one-to-one with the four strokes of a four-stroke engine:
- Intake: fresh charge enters.
- Compression: the piston compresses the charge.
- Power: combustion and expansion produce work.
- Exhaust: burned gases are expelled.
The ideal cycle omits intake and exhaust as separate gas-flow processes. Its constant-volume heating occurs near the transition between compression and expansion. Otto-cycle analysis can also approximate the compression and expansion behavior of some two-stroke spark-ignition engines, despite their different gas-exchange arrangements.
Departures from ideal behavior
Real engine efficiency differs from the cold-air-standard prediction for several reasons:
- Variable heat capacities: gas heat capacities change substantially with temperature, and the constant value does not represent the entire cycle.
- Finite combustion duration: heat release occurs while the piston moves, rather than at a single fixed volume.
- Heat transfer: energy passes from the gases into cylinder walls, the piston, and the cylinder head.
- Irreversibility: combustion, mixing, fluid motion, and pressure losses generate entropy.
- Gas exchange: intake and exhaust require pumping work, especially in throttled operation.
- Mechanical losses: friction and engine-driven auxiliaries reduce useful shaft output.
- Changing gas composition: fuel, combustion products, residual gases, and high-temperature chemical reactions depart from the fixed-air model.
Actual performance is therefore described using measures such as indicated thermal efficiency, based on cylinder work, and brake thermal efficiency, based on useful shaft work.
Compression ratio and knock
Although the ideal formula favors increasing compression ratio, a spark-ignition engine cannot increase it without practical limits. Higher compression raises the pressure and temperature of the unburned mixture, potentially causing engine knock: autoignition of part of the remaining charge, producing rapid pressure oscillations.
Knock limits depend on fuel properties, combustion-chamber design, operating conditions, charge temperature, and ignition timing. Structural loads and heat transfer also constrain engine design. The ideal efficiency formula alone cannot determine an engine’s optimal compression ratio.
Comparison with other cycles
The Diesel cycle substitutes constant-pressure heat addition for the Otto cycle’s constant-volume heat addition. A dual cycle divides heat addition between constant-volume and constant-pressure stages.
For the same compression ratio and the same constant specific heats, the ideal Otto cycle is more efficient than the ideal Diesel cycle with a finite heat-addition cutoff ratio. This restricted comparison does not establish that real gasoline engines are more efficient than real diesel engines: their compression ratios, loads, combustion characteristics, and losses differ.
The Carnot cycle provides the maximum possible heat-engine efficiency between two fixed thermal reservoirs. The Otto cycle receives and rejects heat over ranges of working-fluid temperature, so it is not a Carnot cycle, even though its ideal processes are internally reversible.
Atkinson- and Miller-cycle engine strategies alter the relationship between effective compression and expansion, commonly allowing greater expansion relative to effective compression. Their analysis requires more than the simple Otto-cycle expression based on a single common compression and expansion ratio.
Uses of the model
The Otto cycle is a foundational model in engineering thermodynamics. It isolates the effects of compression ratio and working-fluid properties, provides a reference for interpreting cylinder pressure–volume diagrams, and supports preliminary estimates of temperatures, pressures, heat transfer, and work.
More detailed engine calculations add variable thermodynamic properties, combustion kinetics, heat-transfer models, gas-exchange dynamics, and mechanical losses. The ideal cycle remains useful as a baseline against which those additional effects can be identified.