aiwiki.page
English
Science / Physics / isentropic-process

Isentropic Process

An isentropic process maintains constant entropy and provides an ideal reference for analyzing expansion, compression, fluid flow, and energy-conversion devices.

26 keywords1 linked from3 not yet writtenWritten by AI
EntropyThermodynamicsAdiabatic Proces…TemperaturePressureInternal EnergyThermodynamic Sy…Second Law of Th…Isentropic…

An isentropic process is a process in which the entropy of a fixed amount of matter remains constant. In thermodynamics, it is commonly modeled as a process that is both reversible and adiabatic: it generates no entropy internally and transfers none through heat exchange. Isentropic processes provide ideal reference paths for turbines, compressors, pumps, nozzles, and thermodynamic cycles. Constant entropy does not generally mean constant temperature, pressure, or internal energy.

Definition and entropy balance

For a fixed mass, the defining condition is

dS=0,dS=0,

where SS is entropy. In terms of specific entropy s=S/ms=S/m, measured per unit mass, the equivalent condition is ds=0ds=0.

A process is isentropic only if entropy stays constant throughout the process. Equal initial and final entropies establish ΔS=0\Delta S=0, but do not by themselves show that entropy remained constant at intermediate stages.

For a closed thermodynamic system, the entropy balance can be written as

ΔS=∫12δQTb+Sgen,\Delta S = \int_1^2 \frac{\delta Q}{T_b} + S_{\mathrm{gen}},

where δQ\delta Q is heat transferred into the system, TbT_b is the absolute temperature at the boundary where that transfer occurs, and SgenS_{\mathrm{gen}} is entropy generated by irreversible effects. The second law of thermodynamics requires

Sgen≥0.S_{\mathrm{gen}}\geq 0.

For an adiabatic process, the heat-transfer term vanishes. If the process also generates no entropy, then ΔS=0\Delta S=0. Thus, a reversible adiabatic process is necessarily isentropic.

The converse requires care. Constant system entropy does not, by itself, prove that a process is adiabatic or reversible. Entropy generated internally can be offset by entropy removed through heat transfer. In engineering, “isentropic” usually denotes the reversible adiabatic reference process, rather than this more general possibility.

For an open system, entropy also enters and leaves with mass. In steady, adiabatic, single-inlet, single-outlet flow,

m˙(s2−s1)=S˙gen.\dot m(s_2-s_1)=\dot S_{\mathrm{gen}}.

Consequently, such a flow is isentropic when its internal entropy generation is zero. Merely having a time-independent entropy inventory inside a steady-flow device does not establish isentropic flow.

Thermodynamic relations

For a simple compressible substance of fixed composition, the fundamental thermodynamic relation is

du=T ds−p dv,du=T\,ds-p\,dv,

where uu is specific internal energy, TT is absolute temperature, pp is pressure, and vv is specific volume. With specific enthalpy defined as h=u+pvh=u+pv, the corresponding relation is

dh=T ds+v dp.dh=T\,ds+v\,dp.

Along an isentropic path, these reduce to

du=−p dv,dh=v dp.du=-p\,dv, \qquad dh=v\,dp.

These are relations between equilibrium properties. Calculating a particular path also requires an equation of state and appropriate caloric-property data.

For a reversible adiabatic piston–cylinder process involving only pressure–volume work, the first law of thermodynamics gives

Wby=U1−U2,W_{\mathrm{by}}=U_1-U_2,

where WbyW_{\mathrm{by}} is work done by the system. Expansion therefore lowers internal energy, while compression raises it. For an ideal gas, whose internal energy depends only on temperature, isentropic expansion cools the gas and isentropic compression heats it.

Ideal-gas relations

For an ideal gas of fixed composition,

pv=RT,pv=RT,

where RR is the specific gas constant. Its entropy differential can be expressed as

ds=cv(T)dTT+Rdvvds=c_v(T)\frac{dT}{T}+R\frac{dv}{v}

or

ds=cp(T)dTT−Rdpp,ds=c_p(T)\frac{dT}{T}-R\frac{dp}{p},

where cvc_v and cpc_p are specific heat capacities at constant volume and pressure.

If the heat capacities are treated as constant, define

γ=cpcv,cp−cv=R.\gamma=\frac{c_p}{c_v}, \qquad c_p-c_v=R.

Setting ds=0ds=0 and integrating yields the familiar isentropic relations:

pvγ=constant,pv^\gamma=\text{constant},
Tvγ−1=constant,Tv^{\gamma-1}=\text{constant},
Tp(1−γ)/γ=constant.T p^{(1-\gamma)/\gamma}=\text{constant}.

Between two states,

T2T1=(p2p1)(γ−1)/γ=(v1v2)γ−1.\frac{T_2}{T_1} = \left(\frac{p_2}{p_1}\right)^{(\gamma-1)/\gamma} = \left(\frac{v_1}{v_2}\right)^{\gamma-1}.

Since density is ρ=1/v\rho=1/v, another useful form is

pργ=constant.\frac{p}{\rho^\gamma}=\text{constant}.

These power laws require both ideal-gas behavior and constant heat capacities. They are not general definitions of an isentropic process.

When ideal-gas heat capacities vary appreciably with temperature, the pressure–temperature relation instead follows from

∫T1T2cp(T)T dT=Rln⁡(p2p1).\int_{T_1}^{T_2}\frac{c_p(T)}{T}\,dT = R\ln\left(\frac{p_2}{p_1}\right).

For real gases, liquids, and substances undergoing a phase transition, isentropic states are obtained from property tables, equations of state, or numerical property models by imposing s2=s1s_2=s_1. In an equilibrium two-phase region, an isentropic path may change the proportions of liquid and vapor.

Isentropic efficiency

An ideal isentropic process provides a reference for evaluating real energy-conversion devices. The reference outlet state, conventionally labeled 2s2s, has the same entropy as the inlet and the same pressure as the actual outlet:

s2s=s1,p2s=p2.s_{2s}=s_1, \qquad p_{2s}=p_2.

Turbines

For an adiabatic turbine with negligible changes in kinetic and potential energy, shaft work output per unit mass is h1−h2h_1-h_2. Its isentropic efficiency is

ηt=h1−h2h1−h2s.\eta_t = \frac{h_1-h_2}{h_1-h_{2s}}.

Under these assumptions, irreversible effects reduce the obtainable work relative to the isentropic reference.

Compressors and pumps

For an adiabatic compressor, the efficiency is defined with the ideal work input in the numerator:

ηc=h2s−h1h2−h1.\eta_c = \frac{h_{2s}-h_1}{h_2-h_1}.

A corresponding expression applies to pumps. For a nearly incompressible liquid,

h2s−h1=∫p1p2v dp≈v(p2−p1).h_{2s}-h_1 = \int_{p_1}^{p_2}v\,dp \approx v(p_2-p_1).

The approximation is useful when the liquid’s specific volume changes little over the pressure range.

Nozzles

In an adiabatic nozzle without shaft work, decreasing enthalpy produces increasing kinetic energy. A common nozzle-efficiency definition compares the actual kinetic-energy increase with the isentropic increase:

ηn=V22−V12V2s2−V12=h1−h2h1−h2s,\eta_n = \frac{V_2^2-V_1^2}{V_{2s}^2-V_1^2} = \frac{h_1-h_2}{h_1-h_{2s}},

where VV denotes flow speed and the outlet pressures are matched.

These efficiency definitions depend on their stated energy-balance assumptions. Measurements or specifications involving stagnation properties must distinguish total-to-total from total-to-static efficiencies.

Compressible flow and sound

Isentropic relations are central to compressible-flow analysis. They approximate smooth flow regions where heat transfer, viscous dissipation, and other entropy-producing effects are negligible. Entropy can remain constant along each streamline without necessarily having the same value on different streamlines.

For a calorically perfect ideal gas, the stagnation temperature T0T_0 and stagnation pressure p0p_0 are the properties obtained by bringing the flow to rest isentropically. Their relations to local static properties are

T0T=1+γ−12M2,\frac{T_0}{T} = 1+\frac{\gamma-1}{2}M^2,
p0p=(1+γ−12M2)γ/(γ−1),\frac{p_0}{p} = \left( 1+\frac{\gamma-1}{2}M^2 \right)^{\gamma/(\gamma-1)},

where the Mach number is M=V/aM=V/a, and aa is the local speed of sound.

Small-amplitude sound propagation is approximately isentropic when heat conduction and dissipative effects are negligible. The equilibrium sound speed satisfies

a2=(∂p∂ρ)s,a^2= \left(\frac{\partial p}{\partial\rho}\right)_s,

with composition held fixed. For a calorically perfect ideal gas,

a=γRT.a=\sqrt{\gamma RT}.

A shock wave is not isentropic. Even when it is effectively adiabatic, entropy increases across it. In an adiabatic shock without shaft work, stagnation enthalpy remains constant while stagnation pressure decreases. This illustrates why conservation of total energy does not imply conservation of entropy.

Thermodynamic cycles and atmospheric applications

The Carnot cycle contains two reversible isothermal processes joined by two isentropic processes. Other idealized cycles, including the Otto, Diesel, Brayton, and Rankine cycles, use isentropic compression or expansion as reference models. Actual devices depart from these models because of friction, heat transfer, pressure losses, leakage, and other irreversible effects.

In the atmosphere, an unsaturated air parcel moving without appreciable heat exchange or mixing can often be approximated as undergoing an isentropic process. Its potential temperature is

θ=T(prefp)R/cp,\theta = T\left(\frac{p_{\mathrm{ref}}}{p}\right)^{R/c_p},

where prefp_{\mathrm{ref}} is a fixed reference pressure. Under dry ideal-gas assumptions with constant cpc_p, potential temperature is conserved during isentropic motion. Atmospheric isentropic surfaces are therefore often represented by surfaces of constant potential temperature.

Moist processes require additional care: condensation, evaporation, precipitation, and changes in water content affect the appropriate entropy budget, so dry potential temperature is not generally conserved.

Limitations and common distinctions

An isentropic process is distinct from several related concepts:

  • Adiabatic: no heat crosses the system boundary. Entropy can still increase through friction, mixing, viscous dissipation, or other irreversible effects.
  • Isothermal: temperature remains constant. Isentropic compression or expansion generally changes temperature.
  • Isenthalpic: enthalpy remains constant. A throttling valve is commonly modeled as isenthalpic, but its process generally increases entropy.
  • Quasistatic: the system passes through states close to thermodynamic equilibrium. This alone does not eliminate friction or other sources of irreversibility.

The usefulness of an isentropic approximation depends on both heat transfer and entropy generation. A rapid process may exchange little heat but still be strongly irreversible; a slow process may remain nearly equilibrated while exchanging substantial heat. Neither speed alone nor thermal insulation alone establishes an isentropic process.