Hess’s law states that the enthalpy change of a chemical reaction depends only on the initial and final states, not on the sequence of steps connecting them. Consequently, if a reaction can be expressed as the sum of other reactions, its enthalpy change equals the corresponding sum of their enthalpy changes. The law is fundamental to thermochemistry, enabling the calculation of reaction enthalpies that are difficult to measure directly.
Statement and thermodynamic basis
For a process connecting an initial state to a final state , either directly or through an intermediate state ,
The same principle applies to any number of intermediate steps:
The initial and final states must be fully specified, including composition, physical phases, temperature, and pressure. Changing these conditions can change the enthalpy difference.
Hess’s law follows from enthalpy being a state function: its value depends on a system’s state rather than its history. Enthalpy is defined by
where is internal energy, is pressure, and is volume. Its path independence is consistent with the first law of thermodynamics and conservation of energy.
Although the law is traditionally expressed in terms of “heat summation,” heat itself is not a state function. For a closed system at constant pressure, with only pressure–volume work and negligible changes in macroscopic kinetic and potential energies,
Under these conditions, measured heat transfer equals the enthalpy change. Hess’s law remains valid as an enthalpy relation when these conditions do not hold, but the heat exchanged need not equal .
Historical development
The law is named after Germain Henri Hess, who formulated it in 1840 from experimental investigations of reaction heats. His work showed that the total heat associated with a chemical transformation could be obtained by adding the heats of suitable intermediate transformations.
Hess’s formulation preceded the mature framework of thermodynamics. It provided an early quantitative expression of the path independence of reaction energy changes and became a foundation for systematic thermochemical measurements and tables.
Combining thermochemical equations
A thermochemical equation specifies both a balanced chemical equation and its associated enthalpy change. Applying Hess’s law involves manipulating these equations according to three rules.
Reversing a reaction reverses the sign of its enthalpy change.
implies
Multiplying a reaction by a factor multiplies its enthalpy change by the same factor.
Adding reactions adds their enthalpy changes. Species appearing on both sides cancel only when they represent the same substance in the same physical and thermodynamic state.
These rules reflect the stoichiometry of the reactions and the extensive character of enthalpy. A quoted reaction enthalpy therefore requires a specified equation: doubling every coefficient doubles the enthalpy change for the reaction as written.
Example: formation of carbon monoxide
Consider the following rounded standard reaction enthalpies at :
Reversing the second reaction and adding it to the first cancels carbon dioxide, giving
Its standard reaction enthalpy is therefore
Here, the molar unit refers to one mole of reaction as written, producing one mole of carbon monoxide. The indirect calculation is useful because direct oxidation of graphite need not yield carbon monoxide alone.
Standard enthalpies of formation
An important application of Hess’s law uses tabulated standard enthalpies of formation. The standard enthalpy of formation, , is the enthalpy change when one mole of a substance forms from its constituent elements in their reference states, with all substances in their standard states at the specified temperature.
For a balanced reaction,
where the values are positive stoichiometric coefficients.
This expression represents an imagined path in which the reactants are converted back into their constituent elements and those elements are then converted into the products. That path need not be experimentally realizable.
By convention, the standard enthalpy of formation of an element in its reference state is zero. This does not mean that the element has zero absolute enthalpy. For example, graphite has zero standard enthalpy of formation under ordinary reference conditions, whereas diamond does not.
The standard pressure is . A temperature of is commonly used for tabulation, but standard-state notation does not itself prescribe a temperature.
Thermochemical cycles and applications
A thermochemical cycle consists of alternative paths connecting the same states. When the path returns to its starting state, the total enthalpy change is zero:
This allows an unknown step to be calculated from the remaining steps.
Combustion and calorimetry
Measured combustion enthalpies can be combined to determine formation enthalpies or compare the enthalpies of related compounds. If two substances can be transformed into the same final products, their combustion enthalpies can provide the enthalpy difference between them, provided the equations are balanced consistently.
Experimental values often come from calorimetry. A bomb calorimeter operates approximately at constant volume and measures a heat associated with , rather than directly with . Conversion between the quantities may therefore be necessary. For reactions with ideal-gas reactants or products at a common temperature,
when the pressure–volume contributions of condensed phases are neglected. Here is the change in the total gaseous stoichiometric coefficient and is the gas constant.
Ionic solids
The Born–Haber cycle applies Hess’s law to the formation of ionic solids. It combines steps such as atomization, ionization, electron attachment, and crystal formation to infer lattice energies or lattice enthalpies. Care is necessary because lattice quantities may be defined either for separating a crystal into gaseous ions or for forming it from those ions; these conventions have opposite signs.
Phase changes and solutions
Cycles can combine reaction enthalpies with enthalpies of melting, vaporization, dissolution, or mixing. For example, a reaction producing liquid water has a different enthalpy from the otherwise identical reaction producing water vapor. A vaporization or condensation step connects the two results.
For solutions, concentration and solvent conditions also matter. Enthalpies measured at different concentrations cannot automatically be combined as though the initial and final states were identical.
Temperature dependence
Hess’s law applies at any specified temperature, but reaction enthalpies generally change with temperature. This dependence is described by Kirchhoff’s relation:
where is the stoichiometric sum of product heat capacities minus that of reactants. Thus,
If the interval includes a phase transition, the corresponding transition enthalpy must also be included. Data tabulated at different temperatures require appropriate corrections before they are combined.
Scope and limitations
Hess’s law is an exact relation between consistently specified thermodynamic states. The accuracy of a numerical result depends on the data and assumptions used.
Important distinctions include:
- A thermochemical path is not necessarily a reaction mechanism. Algebraic intermediate steps need not occur during the actual reaction mechanism.
- Enthalpy does not determine reaction rate. Chemical kinetics and activation barriers govern how quickly a reaction proceeds.
- A negative enthalpy change does not by itself establish spontaneity. At constant temperature and pressure, the relevant thermodynamic criterion involves Gibbs free energy, including the entropy contribution.
- Bond-enthalpy calculations are often approximate. Average bond enthalpies describe averaged gas-phase behavior rather than exact values for every molecular environment.
- Experimental uncertainties propagate through the calculation. Combining several measured enthalpies can produce substantial relative measurement uncertainty, especially when the desired result is a small difference between large quantities.
Analogous addition rules apply to changes in other state functions, including internal energy, entropy, and Gibbs free energy. Hess’s law specifically denotes the thermochemical application to reaction enthalpy.