A gravity dam is a dam that resists the forces exerted by impounded water primarily through its own weight. Usually built of concrete or stone masonry, it transfers these forces into its foundation through compression and shear. Its cross-section is generally broad at the base and narrower at the crest, reflecting the increase in water pressure with depth. Gravity dams are used for water supply, flood control, irrigation, navigation, and hydroelectric power generation.
Structural principle
Water retained behind a dam exerts hydrostatic pressure on its upstream face. For a stationary liquid of approximately constant density, pressure increases linearly with depth:
where is gauge pressure, is water density, is gravitational acceleration, and is depth below the water surface.
For a vertical upstream face retaining water to depth , the horizontal force per unit length of dam is
This force acts at a height above the base. The expression describes the upstream hydrostatic load alone; downstream water, sediment, waves, and other actions must be considered separately.
The dam’s weight provides a downward force that helps resist sliding and produces a stabilizing moment against overturning. Its foundation must carry the resulting stresses without excessive deformation, shear failure, or loss of support. Consequently, a heavy dam is not necessarily a safe dam: foundation strength, geological discontinuities, seepage, and the distribution of loads are all fundamental to stability.
A conventional gravity dam is often analyzed initially as a series of vertical slices perpendicular to its longitudinal axis. Each slice is proportioned to remain stable under the relevant loads. More detailed analysis may account for interaction between adjacent blocks, irregular foundation geometry, and three-dimensional structural behavior.
Form and principal components
The highest part of the dam is the crest. The upstream edge of its base is the heel, and the downstream edge is the toe. A typical solid gravity dam has a nearly vertical upstream face and a sloping downstream face, although both profiles may vary.
An idealized elementary section is triangular: increasing thickness toward the bottom supplies weight where water pressure and overturning effects are greatest. Actual dams depart from this shape to provide crest access, freeboard above the reservoir, spillways, internal passages, and adequate stresses under different loading conditions.
Common components include:
- Spillways, which release excess water without uncontrolled overtopping.
- Outlet works, which permit controlled releases at selected reservoir levels.
- Inspection galleries, which provide access for drainage, instrumentation, inspection, and maintenance.
- Foundation drains, which relieve water pressure beneath the structure.
- Grout curtains, formed by injecting grout into foundation openings to reduce seepage.
- Contraction joints, which divide the concrete into blocks and accommodate construction and temperature effects.
A spillway can be incorporated into the dam body, with water flowing over a shaped crest and down a protected downstream face. Other sections may contain power intakes or conduits. Such openings and changes in geometry require local structural analysis.
Materials and construction methods
Masonry and conventional concrete
Historic gravity dams were commonly built from stone masonry bonded with mortar. Modern large gravity dams are generally concrete structures.
The main body usually consists of mass concrete rather than a heavily reinforced structural frame. Concrete performs well in compression, while the dam’s geometry is intended to limit tensile stresses under specified loading conditions. Reinforced concrete is nevertheless used around openings, in spillway structures, and wherever local bending or other concentrated actions require it.
Conventional concrete is placed in successive layers, or lifts, within construction blocks. Joint surfaces must be prepared to achieve the required bond and shear resistance.
Roller-compacted concrete
Roller-compacted concrete is a low-slump concrete placed in broad layers and compacted with vibratory rollers. It allows earthmoving equipment and relatively continuous placement methods to be used, potentially reducing construction time and cost.
Its structural principle remains that of a gravity dam. Important construction considerations include compaction, bonding between lifts, seepage along lift joints, and the treatment of upstream faces. Mix design and placement procedures must suit the project’s materials, climate, and performance requirements.
Thermal control
Hydration of cement releases heat. In a massive concrete block, the interior may remain warm while exposed surfaces cool, producing temperature differences and restrained contraction that can cause cracking.
Thermal-control measures can include lower-heat mixtures, supplementary cementitious materials, cooling of ingredients, embedded cooling pipes, controlled lift schedules, insulation, and contraction joints. These measures address both the construction-stage temperature rise and longer-term cooling.
Loads and stability assessment
Design considers combinations of permanent, operating, flood, construction, and earthquake loads. The combinations and acceptance criteria depend on the applicable standards and the consequences of failure.
Uplift and seepage
Water entering joints, cracks, or foundation discontinuities creates uplift pressure beneath or within the dam. Uplift reduces the effective compressive force holding a potential sliding surface together.
For a simplified horizontal-base analysis,
where is dam weight, represents other downward vertical loads, and is the resultant uplift force.
Drainage can reduce uplift, while grouting can restrict seepage paths. Neither makes the foundation completely impermeable. Design must allow for plausible pressure distributions, including reduced drainage effectiveness, and operation must include checks on drain performance.
Sliding
Sliding may occur at the concrete–rock contact, along construction joints, or along weak surfaces within the foundation.
An illustrative expression for sliding resistance is
where is an adopted cohesion parameter, is the resisting area, and is the friction angle of the potential sliding surface.
This simplified relation does not establish that cohesion can safely be credited in every case. Design values depend on testing, geological conditions, joint continuity, and the assessment method. Foundation wedges bounded by intersecting rock discontinuities may require three-dimensional analysis.
Overturning and stress distribution
Reservoir pressure tends to rotate the dam downstream. Assessment therefore considers both moment equilibrium and the position of the resultant base force.
For an idealized rectangular base of width , with a linear normal-stress distribution, keeping the resultant within the middle third of the base—an eccentricity satisfying —avoids calculated tensile contact stress.
The middle-third rule is a useful elementary criterion, not a complete modern design method. Actual assessment must consider allowable compression, possible joint opening, changes in uplift after cracking, and the behavior of both concrete and foundation.
Earthquakes and other actions
An earthquake produces inertia forces in the dam and dynamic pressures in the reservoir. The response depends on interaction among the structure, water, and foundation, as well as joint behavior and ground-motion characteristics.
Other loads can include sediment pressure, ice, waves, temperature changes, tailwater pressure, and forces associated with gates or equipment. Finite-element analysis is widely used to investigate stress concentrations, foundation interaction, and dynamic response beyond the capabilities of simple sectional calculations.
Site selection and foundations
Gravity dams generally favor foundations that can support substantial loads with limited deformation. Sound rock is often suitable, but rock type alone does not establish suitability. Weathering, faults, joint orientation, weak seams, permeability, and the geometry of potential sliding blocks can govern the design.
Foundation preparation may involve excavation to competent material, cleaning and treatment of discontinuities, concrete replacement of unsuitable zones, grouting, and drainage. Abutments and nearby slopes also require investigation because instability outside the dam body can threaten the project.
Valley geometry affects the choice of dam type. Gravity dams can be suitable where a broad valley or weaker abutments make arch action unattractive, provided that the foundation can support the structure. Their large material volume can become an economic disadvantage as height and valley width increase.
Comparison with other dam types
An arch dam transfers much of the reservoir load laterally into its abutments through arch action. It can use less concrete than a gravity dam at a suitable narrow, steep-sided site, but requires appropriate valley geometry and strong abutments.
An embankment dam consists mainly of compacted earth or rockfill, with seepage controlled by low-permeability zones or membranes and by filters and drains. It can accommodate some foundation conditions and deformations that would be unfavorable for a rigid concrete structure. Uncontrolled overtopping is especially hazardous unless the dam has been specifically designed and protected for it.
A buttress dam uses a relatively thin water-retaining face supported by spaced structural members. Its load path differs from that of a conventional solid gravity section.
Some dams combine gravity and arch action. A curved plan alone does not establish the classification: the defining issue is how the structure carries its loads.
Historical development and examples
Early masonry dams demonstrated the possibility of retaining water with massive structures, but modern gravity-dam engineering developed with improved understanding of hydrostatics, structural equilibrium, foundation geology, and concrete technology. During the nineteenth and twentieth centuries, analytical design increasingly supplemented empirical rules.
Mass-concrete construction, thermal control, foundation treatment, and mechanized placement enabled much larger projects. Roller-compacted concrete subsequently provided another construction method for gravity dams.
The Three Gorges Dam in China is a major concrete gravity dam. Grand Coulee Dam in the United States is another prominent example. Hoover Dam is classified more specifically as an arch-gravity dam because both its weight and its curved structural action contribute to resistance.
Operation, deterioration, and safety
Long-term safety depends on the behavior of the complete dam–foundation–reservoir system. Monitoring commonly includes reservoir and tailwater levels, uplift pressure, seepage flow, temperature, displacement, joint movement, and cracking. Instruments and sensors are complemented by visual inspection and periodic engineering assessment.
Potential deterioration mechanisms include concrete cracking, freeze–thaw damage, chemical attack, alkali–aggregate reaction, and deterioration of gates and embedded metalwork. Foundation drains may become obstructed, allowing uplift pressures to rise. High-velocity flows can damage spillway surfaces through abrasion or cavitation, while downstream erosion can threaten supporting rock or energy-dissipation structures.
Rehabilitation may involve drainage improvements, grouting, concrete repairs, structural strengthening, or spillway modification. Changes in flood estimates and assessments of earthquake loading can also lead to reassessment even when the structure shows no obvious deterioration.
Environmental and economic considerations
A gravity dam requires substantial quantities of construction material. Its cost and environmental footprint depend on concrete volume, cement content, foundation excavation, transport distances, and construction methods.
Many wider impacts arise from the reservoir and its operation rather than from the gravity structure itself. These can include land inundation, displacement of communities, altered sediment transport, barriers to aquatic migration, and changes in downstream flows and water quality. Reservoir sedimentation can reduce storage and affect outlet operation.
The choice of a gravity dam therefore involves not only structural stability, but also comparison with alternative dam types, water-management arrangements, construction costs, and the social and ecological consequences of the proposed project.