Faraday’s laws of electrolysis are two quantitative laws that relate the amount of substance chemically transformed at an electrode to the electric charge passing through an electrochemical system. Established experimentally by Michael Faraday in 1833–1834, they form a foundation of electrochemistry. In modern notation, their combined expression is , where is the mass transformed, is its molar mass, is the charge used in the specified electrode reaction, is the number of electrons transferred per formula unit, and is the Faraday constant.
First law: chemical change is proportional to charge
The first law states that the mass of a substance deposited, dissolved, or otherwise transformed at an electrode is directly proportional to the charge passing through the corresponding electrode reaction:
Here is the electrochemical equivalent of the substance for that reaction, expressed in kilograms per coulomb in SI units. It depends on both the substance and the reaction involved.
For a constant electric current maintained for a time ,
so that
If the current varies with time, the charge is calculated by integration:
Thus, for a specified reaction, doubling the charge doubles the theoretical amount transformed. Increasing the current while proportionally shortening the duration leaves the theoretical amount unchanged, provided that the same fraction of the current continues to drive that reaction.
The law concerns chemical transformation, not necessarily the accumulation of a solid deposit. It also applies to gas evolution, electrode dissolution, and reactions producing dissolved substances.
Second law: chemical equivalents
The second law states that when the same charge drives different electrode reactions, the masses transformed are proportional to their equivalent masses.
For an electrode reaction, the equivalent mass is
where is the molar mass of the substance and is the number of electrons transferred per formula unit in the balanced reaction. For two reactions receiving the same charge,
For example, silver deposition from silver ions requires one electron per silver atom:
Copper deposition from copper(II) ions requires two:
Consequently, the same charge deposits twice as many moles of silver as copper, assuming complete current efficiency in each reaction. The mass ratio also depends on their different molar masses.
The value of must be obtained from the actual reaction stoichiometry, rather than assigned solely from the identity of the element. Different oxidation states can give different electrochemical equivalents for the same element.
Combined equation and microscopic interpretation
The two laws combine as
Equivalently, if is the amount of substance transformed,
The Faraday constant is the magnitude of the charge carried by one mole of electrons:
where is the Avogadro constant and is the elementary charge. Since both constants have exact defined values in the modern International System of Units, their product is exact; the decimal value shown here is rounded.
The modern explanation follows from the discrete charge of the electron and the balanced electron count in a oxidation–reduction reaction. If transforming one formula unit requires electrons, transforming one mole requires a charge of magnitude .
This interpretation distinguishes electronic conduction in the external circuit from ionic conduction in an electrolyte. Electrons are transferred at electrode interfaces, while ions transport charge through the electrolyte. Electrode reactions can also involve neutral molecules, so is not always simply the charge number of an ion.
Worked examples
Copper deposition
For copper deposition from copper(II) ions, . A constant current of maintained for minutes supplies
Using ,
This is the theoretical deposited mass if all the charge drives copper deposition and the resulting copper is retained.
Water electrolysis
In an acidic representation, the cathodic and anodic reactions for water electrolysis are
and
Thus, forming one mole of hydrogen requires , whereas forming one mole of oxygen requires . With complete current efficiency, the same charge passing through both electrodes produces hydrogen and oxygen in a molar ratio.
The charge is not divided between the two electrodes: the same total charge passes through each interface in the series circuit. Gas volumes require additional specification of temperature, pressure, and water-vapor content.
Current efficiency and practical limitations
In an actual cell, not all externally measured charge necessarily produces the intended product. Competing reactions may consume part of the current, while charging the electrode’s electrical double layer can pass charge without a corresponding net chemical conversion.
The current efficiency, also called Faradaic efficiency, of a specified product is the fraction of total charge assigned to its formation. For a constant overall efficiency ,
For example, hydrogen evolution may compete with metal deposition. A lower metal yield then reflects the division of current between reactions, not a failure of Faraday’s laws.
Measured mass changes can also include effects not represented by the intended electrode reaction: chemical corrosion, precipitation, dissolution of deposited material, retained liquid, or loss of a deposit during handling. Reliable application therefore requires identifying the reaction and distinguishing electrochemical conversion from other material changes.
The laws do not determine how rapidly a reaction proceeds at a given voltage. Reaction rates depend on chemical kinetics, electrode properties, mass transport, and electrolyte conditions. Nor do the laws specify the voltage or energy required for electrolysis. Those questions involve thermodynamics, electrode overpotentials, and resistive losses. Faradaic efficiency is therefore distinct from energy efficiency.
Applications
Electroplating and metal processing. Faraday’s laws connect current and operating time to deposited metal mass. They also underpin calculations in metal electrowinning and electrorefining. For a uniform coating of area and density , its ideal thickness is
Actual thickness may vary across a surface because current density is not necessarily uniform.
Quantitative chemical analysis. In coulometry, the charge needed to carry out a known reaction is measured to determine the amount of analyte. The method depends on known electron-transfer stoichiometry and a well-characterized current efficiency.
Electrochemical production. The laws provide theoretical production rates for substances such as hydrogen, chlorine, and electrodeposited metals. Comparing measured output with the Faradaic prediction helps quantify product selectivity.
Corrosion and batteries. Reaction-specific charge balances relate electrochemical metal dissolution to material loss and connect electrode reactions to theoretical battery capacity. Self-discharge, side reactions, and incomplete utilization can make practical capacities differ from theoretical values.
Historical significance
Faraday developed the laws through systematic experiments comparing the chemical effects of electricity in different substances and cells. They established a quantitative connection between electrical charge and chemical combining proportions decades before the electron was identified.
Their modern form unites conservation of charge with chemical stoichiometry. Despite the shared name, they are distinct from Faraday’s law of induction, which relates an induced electromotive force to a changing magnetic flux.