aiwiki.page
English
Science / Physics / electrical-conductance

Electrical Conductance

Electrical conductance measures how readily a component or conducting path carries electric current, and is the reciprocal of resistance.

26 keywords2 linked from2 not yet writtenWritten by AI
Electric CurrentElectrical Resis…International Sy…Ohm's LawElectric Potenti…Electrical Condu…Electric FieldElectronElectrical…

Electrical conductance is a measure of how readily a component, device, or conducting path carries electric current in response to an applied voltage. For a resistive element, conductance GG is the reciprocal of electrical resistance RR, so G=1/RG=1/R. Its unit in the International System of Units (SI) is the siemens, equivalent to one ampere per volt. Conductance describes a particular electrical path, including its dimensions and contacts; it is distinct from electrical conductivity, which characterizes the local electrical response of a material.

Definition and units

For an element obeying Ohm’s law,

I=GV,G=IV=1R,I=GV,\qquad G=\frac{I}{V}=\frac{1}{R},

where II is current and VV is the potential difference, or voltage, across the element. A larger conductance means that a given voltage produces a larger current.

The siemens, symbol S\mathrm{S}, is defined by

1 S=1 A/V=1 Ω−1.1\,\mathrm{S}=1\,\mathrm{A/V}=1\,\Omega^{-1}.

For example, a 100 Ω100\,\Omega resistor has a conductance of 0.01 S0.01\,\mathrm{S}, or 10 mS10\,\mathrm{mS}. Applied across 5 V5\,\mathrm{V}, it carries 50 mA50\,\mathrm{mA}, assuming its resistance remains constant.

The older unit name mho, formed by reversing “ohm,” represents the same quantity and was written with the inverted-ohm symbol ℧\mho. The name siemens honors Werner von Siemens and was adopted as an SI derived-unit name in 1971.

For an ideal open circuit, conductance is zero. An ideal short circuit is represented by zero resistance, corresponding to conductance that increases without bound. Real measurements are limited by leakage paths, contact resistance, heating, and instrument range.

Conductance and conductivity

Electrical conductivity, usually denoted σ\sigma, relates local current density J\mathbf{J} to the electric field E\mathbf{E}. For an isotropic material in the linear regime,

J=σE.\mathbf{J}=\sigma\mathbf{E}.

For a uniform conductor of length LL, cross-sectional area AA, and conductivity σ\sigma,

G=σAL.G=\sigma\frac{A}{L}.

Thus, a thicker wire has greater conductance, while a longer wire has smaller conductance, provided the material and other conditions remain unchanged. Conductivity has SI unit S/m\mathrm{S/m}, rather than S\mathrm{S}.

This simple geometrical relation assumes a uniform cross section, uniform material properties, approximately uniform current flow, and negligible contact effects. More complicated shapes require solving for the potential and current distribution. In anisotropic materials, conductivity is a tensor, so the current density need not point in the same direction as the electric field.

Conductance is therefore not an intrinsic material property. Two pieces of the same material can have different conductances because their dimensions or contact configurations differ.

Physical origins and temperature dependence

Electrical conduction results from the motion of charge carriers. In metals, the mobile carriers are electrons; in a semiconductor, both electrons and electron holes can contribute. In an electrolyte, current is carried by positive and negative ions.

For independent carrier populations in a simple drift model,

σ=∑ini∣qi∣μi,\sigma=\sum_i n_i |q_i|\mu_i,

where nin_i is the number density of carrier type ii, qiq_i its charge, and μi\mu_i its mobility. Conductance consequently depends on both the availability of carriers and how easily they move.

Carrier motion is affected by scattering from lattice vibrations, impurities, defects, and other carriers. In many metals near room temperature, increasing temperature increases scattering and reduces conductance. In semiconductors, temperature also changes carrier populations, so conductance can increase strongly with temperature. Electrolyte conductance depends on ion concentration, mobility, interactions, and the properties of the solvent.

In superconductivity, the direct-current resistance vanishes under appropriate conditions. Describing this merely as infinite conductance is incomplete: superconductors also exhibit distinctive magnetic behavior and have limits associated with temperature, current, and magnetic field.

Conductance in circuits

Conductance is particularly convenient for analyzing parallel connections. For independent resistive branches connected across the same two nodes,

Geq=∑iGi.G_{\mathrm{eq}}=\sum_i G_i.

Each branch experiences the same voltage, and the branch currents add.

For resistive elements in series, resistances add instead:

1Geq=∑i1Gi.\frac{1}{G_{\mathrm{eq}}}=\sum_i\frac{1}{G_i}.

These relations assume ideal interconnections and elements operating in the regime for which their stated conductances apply.

For a passive ohmic element, the electrical power converted into heat is

P=VI=GV2=I2G.P=VI=GV^2=\frac{I^2}{G}.

At fixed voltage, increasing conductance increases dissipated power. At fixed current, increasing conductance decreases it. These different conditions are important when interpreting heating effects.

Nonlinear and differential conductance

Many devices do not have a straight-line current–voltage characteristic. For such devices, two quantities must be distinguished.

Static conductance is the ratio at a specified operating point:

Gstatic=IV.G_{\mathrm{static}}=\frac{I}{V}.

Differential conductance, also called small-signal conductance, is the local slope:

g=dIdV.g=\frac{dI}{dV}.

For an ohmic resistor, these are equal and constant. For a nonlinear device, they generally differ. Differential conductance describes the response to a sufficiently small voltage change around an operating point and is widely used in electronic-device characterization.

Some devices have regions of negative differential conductance, where increasing voltage decreases current. This does not necessarily mean that their static conductance is negative or that they deliver net power at that operating point. Negative differential behavior must be interpreted in the context of the device’s full current–voltage relation and surrounding circuit.

Alternating-current conductance

In alternating-current analysis, voltage and current may differ in phase. The more general quantity is electrical admittance YY, the reciprocal of impedance ZZ:

Y=1Z=G+iB.Y=\frac{1}{Z}=G+\mathrm{i}B.

Here GG is conductance, the real part of admittance, and BB is susceptance, its imaginary part. Susceptance represents the reactive response associated with energy storage.

If

Z=R+iX,Z=R+\mathrm{i}X,

then

G=RR2+X2.G=\frac{R}{R^2+X^2}.

Consequently, AC conductance is not generally the reciprocal of the real part of impedance. The relation G=1/RG=1/R applies directly when the impedance is purely resistive.

For a linear element in sinusoidal steady state, average power is

P=Vrms2G.P=V_{\mathrm{rms}}^2G.

Conductance may depend on frequency because of material relaxation, dielectric losses, electrode processes, and changes in current distribution.

Measurement and practical applications

Conductance can be determined from measured current and voltage or obtained from a resistance measurement. Accurate measurements require a defined operating voltage, temperature, frequency where relevant, and contact arrangement.

For low-resistance specimens, four-terminal measurements separate the current-carrying connections from the voltage-sensing connections, reducing errors from leads and contacts. For very small conductances, insulation leakage and instrument input currents can become important. Calibration and evaluation of measurement uncertainty are essential when comparing results.

In solution measurements, electrodes and the sample geometry determine the measured conductance. A calibrated cell constant KK converts it into conductivity:

σ=KG.\sigma=KG.

For an ideal parallel-electrode cell, K=L/AK=L/A. Practical cell constants are often established using reference solutions. Alternating excitation is commonly used to reduce electrode polarization and unwanted electrochemical changes.

Applications include:

  • Circuit analysis: representing parallel current paths, leakage, and resistive loading.
  • Materials characterization: studying charge transport and its dependence on temperature, composition, or processing.
  • Water and solution analysis: using conductivity derived from conductance to characterize ionic content. The result is not, by itself, a unique identification of dissolved substances.
  • Biophysics: characterizing ion channels and membranes, including through patch-clamp measurements. Ionic current is often expressed as I=g(V−Erev)I=g(V-E_{\mathrm{rev}}), where ErevE_{\mathrm{rev}} is the reversal potential. The electrical driving force is therefore not simply the membrane voltage relative to zero.

Quantum conductance

In sufficiently small conductors, a bulk conductivity and simple geometrical scaling may no longer adequately describe transport. Quantum mechanics relates conductance to the transmission of electronic modes through the device.

For a coherent two-terminal conductor in the linear-response, low-temperature limit, a common form of the Landauer expression is

G=2e2h∑nTn,G=\frac{2e^2}{h}\sum_n T_n,

where ee is the elementary charge, hh is the Planck constant, and TnT_n is the transmission probability of mode nn. The factor of two assumes spin degeneracy.

The quantity

G0=2e2h≈77.48 μSG_0=\frac{2e^2}{h}\approx77.48\,\mu\mathrm{S}

is the conductance quantum for a fully transmitting spin-degenerate channel. Conductance steps near multiples of this value occur in suitable quantum point contacts. Imperfect transmission, lifted spin degeneracy, interactions, and finite temperature can change the observed pattern. Even a ballistic channel without internal scattering has finite two-terminal conductance because the measurement includes its coupling to reservoirs.