The coefficient of friction, usually denoted by , is a dimensionless quantity used to describe friction between contacting surfaces. In the simplest models, it relates the tangential frictional force to the normal force pressing the surfaces together. Separate coefficients describe the threshold for sliding and resistance during sliding. A coefficient of friction is not generally an intrinsic constant of a single material: it characterizes a pair of surfaces under particular loading, environmental, and motion conditions.
Definition and basic model
For two surfaces sliding against one another, the kinetic coefficient of friction is commonly defined as
where is the magnitude of the frictional force and is the magnitude of the compressive normal force. Both forces have the same physical dimensions, so their ratio has no units in the International System of Units.
In an idealized dry-friction model, the friction force acts tangentially to the contact and opposes relative sliding. It does not necessarily oppose the motion of an entire object: a moving belt, for example, can exert friction that accelerates an object in its direction of travel.
The normal force is not always equal to an object's weight. It depends on the geometry and all forces acting on the object. On a horizontal surface without other vertical forces, , where is mass and is local gravitational acceleration. On an inclined plane, the relationship is different.
The coefficient is generally nonnegative in this conventional formulation, but it is not restricted to values below one. A value above one means that the relevant tangential force exceeds the normal force.
Static and kinetic coefficients
Static friction
Static friction acts when contacting surfaces do not slide relative to one another. In the elementary model, its magnitude adjusts to the force required to prevent sliding, up to a limiting value:
The static coefficient of friction, , is therefore defined through the maximum sustainable static friction:
It is incorrect to assume that static friction always equals . A stationary block subject to a small horizontal force may experience an equally small opposing friction force. Equality applies at the idealized threshold of gross sliding.
The measured threshold can depend on how long the surfaces have remained in contact, the loading rate, vibration, and microscopic motion preceding gross slip.
Kinetic friction
The kinetic, or sliding, coefficient of friction describes resistance once sliding is occurring:
For many dry surface pairs, is lower than the maximum static coefficient. This is a useful empirical tendency, not a universal law. Sliding friction can increase or decrease with speed, and the transition from sticking to sliding can be more complex than two constant coefficients imply.
A combination of frictional weakening and elastic compliance can produce stick–slip motion, in which intervals of sticking alternate with sudden sliding. Such behavior occurs in machinery, bowed musical instruments, and some models of motion on geological faults.
Physical origin
Nominally smooth surfaces usually touch only at scattered microscopic high points, or asperities. The real area of contact can therefore be much smaller than the apparent geometric contact area.
Several mechanisms contribute to friction:
- Adhesion: contacting regions form junctions that resist tangential displacement.
- Deformation and ploughing: harder surface features or trapped particles deform or displace softer material.
- Viscoelastic losses: materials such as rubber dissipate energy as they deform around surface features.
- Surface films and debris: oxides, contaminants, lubricants, and wear particles alter the way forces are transmitted.
A simplified adhesion model writes the tangential force as
where is an effective interfacial shear strength and is the real contact area. If grows approximately in proportion to normal load, friction also grows approximately in proportion to normal load. This provides one explanation for an approximately constant coefficient.
The mechanisms are studied within tribology, the science and engineering of interacting surfaces in relative motion. Their relative importance changes with material properties, surface preparation, environment, and scale. Friction cannot generally be explained by roughness alone; very smooth, clean surfaces can adhere strongly.
Empirical laws and historical development
The elementary dry-friction model is often called Amontons–Coulomb friction. Its principal approximations are that:
- Sliding friction is proportional to normal load.
- Friction is approximately independent of apparent contact area.
- Sliding friction is approximately independent of speed over a limited operating range.
Leonardo da Vinci investigated friction in the late fifteenth century. Guillaume Amontons published influential experimental laws in 1699, and Charles-Augustin de Coulomb extended the experimental study of static and sliding friction in the eighteenth century.
These laws are empirical approximations, not fundamental laws of classical mechanics. In particular, approximate independence from apparent area does not mean that actual microscopic contact is irrelevant. It reflects how contact area and contact stresses change under load.
Measurement
Inclined-plane method
A simple measurement of static friction uses a plane whose inclination is gradually increased. For a block about to slide under its own weight,
so that
where is the critical inclination.
This relationship assumes that the block slides rather than rolls or tips, that no other significant forces act, and that the loading procedure does not introduce substantial disturbances.
Force-based testing
A specimen can also be pulled across a surface while tangential and normal forces are measured. The peak force associated with the onset of sliding may be used to estimate a static coefficient, while the force during established sliding gives a kinetic coefficient.
Common tribometer configurations include pin-on-disc, ball-on-disc, reciprocating sliding, and block-on-ring arrangements. Different configurations impose different contact pressures, sliding paths, thermal conditions, and opportunities for debris accumulation. Their results are not automatically interchangeable.
A meaningful test report specifies the material pair, surface preparation, load, speed, environment, duration, and method used to calculate the coefficient. Calibration of force sensors and evaluation of measurement uncertainty are important because alignment errors, vibration, and instrument compliance can affect the result.
Dependence on operating conditions
A coefficient should normally be treated as a property of the contact system under stated conditions, rather than a universal material constant.
Important influences include:
- Load and contact pressure: deformation mechanisms and the real contact area may change with load.
- Sliding speed: speed affects junction formation, lubricant-film behavior, and dissipation.
- Temperature: bulk temperature and local frictional heating can alter material strength, films, and chemical reactions.
- Environment: humidity, gases, vacuum, and contamination can change adhesion and surface chemistry.
- Surface history: wear, polishing, oxidation, and running-in modify the interface during use.
- Direction: textured surfaces and anisotropic materials can exhibit direction-dependent friction.
Consequently, tables of coefficients are approximate guides. Entries such as “steel on steel” omit many conditions that may be decisive in practice.
Lubricated contacts and related quantities
Lubrication changes how the load is supported and how tangential resistance arises. In boundary lubrication, surface films and asperity interactions remain important. In mixed lubrication, solid contact and fluid-film support coexist. In full-film lubrication, the surfaces are substantially separated, and resistance arises largely from shearing the lubricant.
A ratio of tangential resistance to normal load can still be reported, but it may vary strongly with speed, load, and lubricant viscosity. The Stribeck curve represents characteristic changes in friction across lubrication regimes.
Several related quantities require distinction:
- A rolling-resistance coefficient describes resistance to rolling and is not generally interchangeable with a sliding coefficient. Some conventions use a force ratio; others use a resistance length relating a resisting moment to normal load.
- A fluid skin-friction coefficient commonly normalizes wall shear stress by a dynamic-pressure scale, rather than by the normal contact force between solids.
- An internal friction coefficient in granular materials relates shear resistance to normal stress within a bulk material. It is related to, but not identical with, friction between two solid surfaces.
Applications and model limitations
Coefficients of friction are used in the analysis of brakes, clutches, belt drives, fasteners, bearings, manufacturing processes, and tire–road contact. With Newton’s laws of motion, they allow estimates of slipping thresholds, acceleration, and required holding forces.
For ideal steady sliding through distance , with constant normal load and coefficient, the magnitude of dissipated mechanical work is
The mechanical energy is converted mainly into heat, with additional contributions from deformation, wear, and other interfacial processes.
A constant-coefficient model becomes inadequate when adhesion is significant compared with the imposed load, friction depends strongly on speed or contact history, or the interface evolves substantially. Adhesive contacts, for example, can resist tangential motion even when the externally applied normal load is near zero, making a simple force ratio difficult to interpret.
More detailed descriptions include load-dependent friction laws, velocity-dependent models, and rate-and-state formulations that account for the evolving condition of the interface. In these settings, a reported coefficient remains useful only when its definition and operating conditions are specified.