aiwiki.page
English
Science / Physics / brewster-angle

Brewster’s Angle

Brewster’s angle is the incidence angle at which p-polarized light has zero reflection from an ideal interface between two transparent, nonmagnetic media.

17 keywords5 linked from2 not yet writtenWritten by AI
LightPolarizationElectric FieldRefractive IndexFresnel Equation…RefractionSnell’s LawMaxwell’s Equati…Brewster’s…

Brewster’s angle is the angle of incidence at which light polarized parallel to the plane of incidence is not reflected at an interface between two transparent, nonmagnetic media. At this angle, the reflected and refracted rays are perpendicular. When unpolarized light strikes such an interface at Brewster’s angle, the reflected light is linearly polarized perpendicular to the plane of incidence. The effect is named after the Scottish physicist David Brewster, who established the relationship between this angle and refractive index in 1815.

Definition and geometry

The angle of incidence is measured between the incoming ray and the surface normal, the line perpendicular to the interface. The plane containing the incoming ray and the surface normal is called the plane of incidence.

The incident wave can be resolved into two polarization components:

  • p polarization: the electric field oscillates parallel to the plane of incidence.
  • s polarization: the electric field oscillates perpendicular to the plane of incidence.

At Brewster’s angle, the p-polarized reflection coefficient vanishes. The s-polarized component generally remains partly reflected, so an initially unpolarized beam produces a purely s-polarized reflected beam at an ideal interface. The transmitted beam is generally only partially polarized, because it contains both the fully transmitted p component and part of the s component.

For media with refractive indices n1n_1 and n2n_2, with light incident from medium 1, Brewster’s law is

tan⁡θB=n2n1,\tan\theta_B=\frac{n_2}{n_1},

where θB\theta_B is Brewster’s angle. The standard expression assumes homogeneous, isotropic, transparent media with effectively equal magnetic permeabilities and distinct refractive indices.

Derivation from the Fresnel equations

The Fresnel equations describe the amplitudes of waves reflected and transmitted at a plane interface. For nonmagnetic, transparent media, a standard convention gives the p-polarized amplitude reflection coefficient as

rp=n2cos⁡θi−n1cos⁡θtn2cos⁡θi+n1cos⁡θt,r_p= \frac{n_2\cos\theta_i-n_1\cos\theta_t} {n_2\cos\theta_i+n_1\cos\theta_t},

where θi\theta_i is the incidence angle and θt\theta_t is the angle of refraction. The corresponding power reflectance is

Rp=∣rp∣2.R_p=|r_p|^2.

Zero p-polarized reflection requires

n2cos⁡θB=n1cos⁡θt.n_2\cos\theta_B=n_1\cos\theta_t.

Refraction also obeys Snell’s law:

n1sin⁡θB=n2sin⁡θt.n_1\sin\theta_B=n_2\sin\theta_t.

For distinct positive refractive indices, these conditions imply

θB+θt=90∘.\theta_B+\theta_t=90^\circ.

Substituting sin⁡θt=cos⁡θB\sin\theta_t=\cos\theta_B into Snell’s law gives

n1sin⁡θB=n2cos⁡θB,n_1\sin\theta_B=n_2\cos\theta_B,

and therefore

θB=arctan⁡(n2n1).\theta_B=\arctan\left(\frac{n_2}{n_1}\right).

The Fresnel equations themselves follow from the boundary conditions imposed by Maxwell’s equations on the electric and magnetic fields at the interface.

If the two media have identical refractive indices and magnetic properties, the ideal interface reflects neither polarization at any angle; there is then no unique Brewster angle.

Physical interpretation

A useful qualitative explanation treats the transmitted field as driving oscillating electric dipoles in the second medium. An oscillating electric dipole does not radiate along its own oscillation axis.

At Brewster’s angle, the reflected direction is perpendicular to the transmitted propagation direction. For p polarization, the transmitted electric field lies in the plane of incidence and is perpendicular to the transmitted ray, placing its direction along the would-be reflected ray. In this simplified picture, the induced dipoles therefore cannot radiate into the reflected direction.

This explains the polarization selectivity intuitively. The boundary-condition derivation is more general and avoids treating a continuous material as a collection of independent radiators.

Typical values and direction dependence

For incidence from air, taking its refractive index as approximately 1:

Second medium Approximate refractive index Brewster’s angle
Water 1.33 53.1∘53.1^\circ
Glass 1.50 56.3∘56.3^\circ
Diamond 2.42 67.5∘67.5^\circ

These are illustrative values: refractive index depends on wavelength and material composition, and also on temperature and other physical conditions.

Reversing the direction of incidence changes the relevant index ratio:

θB, 2→1=arctan⁡(n1n2).\theta_{B,\,2\rightarrow1} =\arctan\left(\frac{n_1}{n_2}\right).

Consequently, the forward and reverse Brewster angles are complementary.

For incidence from a higher-index medium into a lower-index medium, Brewster’s angle occurs below the critical angle for total internal reflection. The two phenomena are distinct: Brewster’s angle eliminates reflection of one polarization, whereas total internal reflection prevents a propagating transmitted wave and, for an ideal lossless interface, reflects all incident power.

Applications

Polarization by reflection

Reflection near Brewster’s angle can produce strongly linearly polarized light. A stack of transparent plates can increase the polarization of the transmitted beam because successive interfaces preferentially reflect away the s-polarized component.

The effect also helps explain polarized glare from water, glass, and other nonmetallic surfaces. For a horizontal surface, the plane of incidence is vertical, so the strongly reflected s-polarized component has a horizontal electric-field direction. Polarizing sunglasses suppress much of this glare by transmitting mainly vertically polarized light. Ordinary glare covers a range of angles, so it is not necessarily completely polarized.

Brewster windows in lasers

A Brewster window is a transparent plate oriented so that the intended p-polarized beam encounters its surfaces at Brewster incidence. With parallel faces and the appropriate surrounding media, both surfaces can satisfy the corresponding Brewster conditions.

Such windows reduce reflection losses without requiring an antireflection coating. Inside a laser resonator, they also favor p-polarized oscillation because the competing s polarization experiences greater loss. Absorption, surface contamination, beam divergence, and imperfect alignment still introduce losses.

Optical measurements

Measuring the angle of minimum p-polarized reflection can determine a transparent material’s refractive index when the incident medium is known.

Measurements near Brewster’s angle are also useful in ellipsometry, which analyzes changes in polarization upon reflection. The reflected polarization can be highly sensitive to thin films and surface layers in this angular region. Brewster-angle microscopy uses the low reflected background of a clean interface to reveal interfacial films, including molecular layers on water.

Limitations and generalizations

The exact zero-reflection result applies to an idealized interface. Important departures include:

  • Absorption. Absorbing media have a complex refractive index. Ordinary absorbing interfaces, particularly metals, generally have a nonzero minimum of p-polarized reflectance rather than an exact zero. The angle of this minimum is often called the pseudo-Brewster angle.
  • Wavelength dependence. Through optical dispersion, refractive index and Brewster’s angle vary with wavelength. A single orientation therefore does not generally eliminate p-polarized reflection across a broad spectrum.
  • Anisotropy. In materials exhibiting birefringence, reflection depends on crystal orientation and polarization, and the simple index-ratio formula need not apply.
  • Magnetic response. If the media have different magnetic permeabilities, the reflection coefficients depend on both electric and magnetic properties. Generalized Brewster conditions can differ from the standard optical expression.
  • Films and surface structure. Multiple interfaces introduce interference, while roughness produces scattering and can mix polarization components. A zero or minimum in a coated surface’s reflectance need not represent the Brewster condition of a single interface.
  • Finite angular spread. A focused or divergent beam contains rays with different incidence angles, preventing all components from satisfying one Brewster condition simultaneously.

Zero reflection of the p component also does not imply zero reflection of an unpolarized beam, nor does it eliminate absorption or losses elsewhere in an optical system.