Thin-film interference is the interference of light waves reflected or transmitted at the different boundaries of a thin layer of material. The waves acquire different phases through propagation and reflection, so their superposition strengthens some wavelengths and suppresses others. This produces the shifting colors of soap bubbles and oil slicks and underlies antireflection coatings, interference filters, and multilayer mirrors. Although the simplest examples involve films comparable in thickness to a visible wavelength, the same principles apply at other wavelengths and in thicker layers when sufficient coherence is maintained.
Physical mechanism
When light encounters a boundary between materials with different refractive indices, part is generally reflected and part transmitted. In a transparent film, the transmitted wave can reflect from the second boundary and emerge alongside the wave reflected at the first. Additional internal reflections produce further emerging waves.
These waves combine according to the superposition principle. Their relative phases determine whether the resulting intensity is increased or reduced. For two coherent contributions of the same polarization,
where and are their individual intensities and is their phase difference. Equal-phase contributions reinforce one another; contributions differing by oppose one another. Complete cancellation requires equal amplitudes as well as opposite phases.
Thin-film interference is commonly described as division of amplitude: a single incident wave is split into reflected and transmitted components that subsequently overlap. It differs geometrically from familiar two-slit experiments, in which spatially separated portions of a wavefront are brought together.
Optical path and reflection phase
Consider a uniform film of thickness and refractive index , between an incident medium of index and a substrate of index . Let be the propagation angle inside the film, measured from the surface normal. Refraction relates this angle to the external incidence angle :
For the first two reflected contributions, the phase difference arising from propagation is
where is the wavelength in vacuum. The corresponding optical path difference is
The cosine factor accounts for comparing the emerging waves at a common wavefront. Simply using the length of the internal round trip, , gives the wrong interference condition.
Reflection can introduce an additional phase change. At normal incidence between transparent, nonmagnetic media, reflection from a lower-index medium toward a higher-index medium reverses the electric-field phase by ; reflection toward a lower-index medium does not. Thus,
where is the relative phase contribution of the two reflections.
For oblique incidence, polarization must also be considered. The Fresnel equations determine the reflection amplitudes and phases for each polarization. Absorbing materials and total internal reflection can introduce phase shifts that are not restricted to zero or .
Conditions for bright and dark reflection
In the simple transparent-film case, the familiar conditions depend on whether exactly one of the two reflected waves undergoes a phase reversal.
| Relative reflection phase | Constructive reflected interference | Destructive reflected interference |
|---|---|---|
| One phase reversal | ||
| Zero or two phase reversals |
Here is a nonnegative integer, with physically realizable orders determined by the geometry. A destructive phase condition does not by itself guarantee zero reflected intensity: the interfering amplitudes must also match.
For a soap film in air, the front-surface reflection undergoes a phase reversal, while the reflection from the film’s inner boundary does not. A sufficiently thin film therefore appears dark in reflection because the two principal contributions nearly cancel. Strong cancellation assumes negligible absorption and comparable surroundings on both sides.
In a lossless system, reflected and transmitted powers together equal the incident power. Consequently, minima in total reflectance correspond to maxima in total transmittance. Absorption changes that simple complementary relationship.
Colors, fringes, and coherence
White light contains a broad range of wavelengths. A particular film thickness reinforces some parts of that spectrum more than others, giving the reflected light a color. This is a form of structural coloration: wavelength selection arises from physical structure rather than primarily from selective absorption by pigments.
Several factors govern the appearance:
- Thickness: A draining soap film develops bands as its thickness varies under gravity and fluid flow.
- Viewing angle: The internal angle changes the optical phase thickness. For a fixed interference order, increasing incidence angle generally shifts the selected wavelength toward shorter wavelengths, apart from complications such as dispersion.
- Material properties: Dispersion makes refractive index wavelength-dependent; absorption alters both amplitudes and phases.
- Illumination: Monochromatic illumination produces bright and dark fringes rather than the many colors seen under white light.
- Averaging: Roughness, thickness variation, or a broad range of illumination angles can wash out interference contrast.
Interference also requires adequate optical coherence. The contributing waves must retain a sufficiently stable phase relationship over their path difference and over the measurement interval. Broadband illumination generally provides a shorter coherence length than narrowband illumination. Thus, visibly colored fringes under white light are usually associated with small optical path differences.
For a film of constant thickness, different observation angles can produce fringes of equal inclination. For a film whose thickness varies across its surface, the pattern can trace approximately equal thicknesses, producing fringes of equal thickness.
Newton’s rings and historical development
Thin-film colors became important evidence in the historical development of optics. Isaac Newton investigated the colored rings produced by a curved glass surface placed against a flat plate and described thin-plate colors in Opticks, published in 1704. Their eventual wave explanation required both propagation phase and phase changes at reflection.
In Newton’s rings, the thin layer is usually an air gap between a plano-convex lens and a flat glass plate. If the lens has radius of curvature , then near the point of contact the gap thickness is approximately
where is distance from the center.
For monochromatic light of vacuum wavelength , near-normal incidence, and an ideal air gap, the reflected dark-ring radii satisfy approximately
The central spot is dark at true optical contact because one reflected contribution undergoes a phase reversal. Dust, deformation, or a residual gap can change the central appearance. Ring measurements can determine lens curvature, wavelength, or departures from surface flatness.
Multiple reflections and multilayers
A two-wave description explains many observations, but every partially reflecting interface generates additional contributions. Accurate calculations sum all these waves, including their phases.
For a single transparent layer at normal incidence, the total amplitude reflection coefficient can be written
with
Here is the power reflectance. This expression includes all internal round trips rather than only the first two reflected waves.
Stacks containing many layers are commonly treated using the optical transfer-matrix method. Related multiple-beam interference produces the resonances of a Fabry–Pérot interferometer. High interface reflectivity makes the resulting spectral features sharper than those of a weakly reflecting single film.
Applications
Antireflection coatings
A single-layer antireflection coating can suppress reflection at a chosen wavelength. For transparent, nonmagnetic materials at normal incidence, an ideal design has
The quarter-wave optical thickness places the principal reflected contributions in opposition, while the index condition matches their amplitudes. Under these assumptions, the exact multilayer expression also gives zero reflectance at the design wavelength.
A single layer cannot generally eliminate reflection across a broad spectrum and a wide range of angles. Multilayer designs improve performance for camera lenses, optical instruments, displays, and solar cells.
Mirrors and filters
Alternating high- and low-index layers can form a dielectric mirror. Quarter-wave layers designed for a target wavelength make reflections from successive interfaces reinforce one another, producing high reflectance over a spectral band.
Interference filters use multilayer structures to transmit or reject selected wavelength ranges. They are used in spectroscopy, imaging, telecommunications, and astronomy. Their passbands often shift with incidence angle, which matters in instruments receiving light over a broad cone.
Measurement and sensing
Thin-film interference is used in interferometry to measure thickness, surface shape, and small displacements. Reflectance spectra can reveal film thickness when refractive index is sufficiently well known. Ellipsometry measures changes in polarization upon reflection and fits optical models to infer thickness and material properties.
Such measurements can be ambiguous: different combinations of thickness and refractive index may produce similar signals. Measurements across several wavelengths or angles, together with appropriate material models, help distinguish them.
Scope and limitations
The simplest formulas assume smooth, parallel boundaries; uniform refractive index; negligible absorption; and well-defined incidence angle and polarization. Real films may require more elaborate treatment because of roughness, graded composition, anisotropy, scattering, or thickness variations.
Not every rainbow-colored surface is a single-film interference effect. A diffraction grating separates wavelengths through diffraction from repeated structures, while many biological colors involve complex three-dimensional arrangements. Conversely, the absence of visible color does not establish the absence of interference: a film may act outside the visible spectrum, produce only a weak modulation, or be observed under conditions that average away its fringes.