aiwiki.page
English
Science / Physics / standard-gravity

Standard Gravity

Standard gravity is the conventional, exactly defined acceleration of 9.80665 metres per second squared, used as a reference in measurement and engineering.

15 keywords3 linked fromWritten by AI
EarthInternational Sy…MetreSecondMeasurement Unce…GravityMoonSunStandard G…

Standard gravity is a conventional reference value for gravitational acceleration, defined as exactly 9.80665 m s−29.80665\ \mathrm{m\,s^{-2}} and usually denoted gng_{\mathrm n} or g0g_0. It approximates the acceleration of a freely falling body near the surface of Earth, but it is not the actual acceleration at every location. Its purpose is to provide a fixed reference for expressing accelerations, defining certain force units, and performing standardized calculations.

Definition and status

The defining value is

gn=9.80665 m s−2.g_{\mathrm n}=9.80665\ \mathrm{m\,s^{-2}}.

In the International System of Units (SI), acceleration is expressed in metres per second squared. Standard gravity is a specified acceleration, not an SI base unit or an additional fundamental constant of nature.

Its numerical value is exact by convention. Consequently, standard gravity itself has no measurement uncertainty. Measurements of actual gravitational acceleration, however, do have uncertainty and need not agree with this reference value.

The notation gg alone often denotes local gravitational acceleration rather than the standard value. Its meaning must therefore be established from context. Neither gg nor gng_{\mathrm n} should be confused with the universal gravitational constant GG, which appears in Newton’s law of gravitation.

Difference from local gravity

Local gravity varies with position and time. Near Earth’s surface, the acceleration experienced by a body falling from rest relative to the ground reflects both gravitational attraction and the effect of Earth’s rotation.

The principal sources of variation include:

  • Latitude: Earth’s rotation reduces effective gravity most strongly near the equator. Earth’s equatorial bulge also places the equatorial surface farther from the planet’s centre.
  • Elevation: Gravity generally decreases with increasing height above Earth’s surface.
  • Mass distribution: Mountains, variations in rock density, and other geological structures produce local gravity anomalies.
  • Time-dependent effects: Tidal influences from the Moon and Sun, together with changes in nearby masses, cause smaller variations.

Representative sea-level values range from about 9.78 m s−29.78\ \mathrm{m\,s^{-2}} near the equator to about 9.83 m s−29.83\ \mathrm{m\,s^{-2}} near the poles. Standard gravity lies between these values.

Standard gravity is also distinct from normal gravity in geodesy. Normal gravity is calculated from an idealized model of Earth and varies with latitude and height. Despite the historical expression “normal acceleration of gravity” for the standard constant, the two concepts should not be treated as interchangeable.

Historical adoption

The third General Conference on Weights and Measures adopted 980.665 cm s−2980.665\ \mathrm{cm\,s^{-2}}, equivalent to 9.80665 m s−29.80665\ \mathrm{m\,s^{-2}}, as the standard acceleration due to gravity in 1901.

The value was intended to represent terrestrial gravity approximately at sea level and latitude 45∘45^\circ. That historical reference explains its scale, but does not define it as the currently measured gravity at a particular site. Its modern role is that of an exact conventional value, independent of refinements in gravity measurements or models of Earth.

The same 1901 resolution clarified the distinction between mass and weight: mass is a property measured in kilograms, whereas weight is a force associated with gravity. This distinction was important because everyday and technical usage often used the same names for mass and force quantities.

Applications

Converting mass to a conventional force

For a body at rest relative to Earth, its weight is commonly written

W=mglocal,W=mg_{\text{local}},

where mm is its mass and glocalg_{\text{local}} is the local effective gravitational acceleration. Substituting standard gravity gives a conventional reference force:

Wn=mgn.W_{\mathrm n}=mg_{\mathrm n}.

Thus, a mass of one kilogram corresponds to a standard reference weight of exactly 9.80665 N9.80665\ \mathrm N. Its actual weight may differ with location.

The kilogram-force, a non-SI unit, is defined through this relationship:

1 kgf=9.80665 N1\ \mathrm{kgf}=9.80665\ \mathrm N

exactly. Standard gravity also enters the definition of pound-force.

Expressing acceleration in multiples of gravity

In engineering, aviation, and vibration testing, accelerations are often expressed in multiples of standard gravity. An acceleration of 3gn3g_{\mathrm n}, for example, is

a=3gn=29.41995 m s−2.a=3g_{\mathrm n}=29.41995\ \mathrm{m\,s^{-2}}.

Here, “g” is a reference scale for acceleration, not a unit of mass. In discussions of loads or accelerometer readings, it often describes acceleration associated with non-gravitational support forces. An accelerometer resting on a horizontal surface typically registers about one g, whereas an ideal freely falling accelerometer registers approximately zero, even though gravity is acting on it.

Pressure and instrument calibration

Standard gravity is used in conventional definitions of some pressure units based on fluid columns. The hydrostatic relationship

Δp=ρgh\Delta p=\rho gh

shows why: the pressure difference depends on fluid density, column height, and gravitational acceleration. A reproducible unit definition requires specified reference conditions rather than an unspecified local value of gg.

In precision calibration, the distinction between standard and local gravity is essential. Instruments that generate force using known masses, or infer mass from measured force, may require local-gravity corrections. The exactness of standard gravity does not remove uncertainties in the masses, instruments, or environmental conditions used to realize a measurement.