The solubility product, usually denoted , is the equilibrium constant for the dissolution of an ionic solid into its constituent dissolved ions. It expresses the condition of chemical equilibrium between a specified solid phase and a saturated solution at a given temperature and pressure. Solubility products are used to calculate solubility, predict whether a precipitate can form, and describe the behavior of minerals, salts, and other sparingly soluble compounds in natural and industrial systems.
Definition and thermodynamic basis
Consider a solid with the formula , which dissolves according to
where and are positive integers and electrical neutrality requires . For a pure solid assigned unit activity, its solubility product is
where each is the dimensionless thermodynamic activity of a dissolved species. The exponents follow directly from the stoichiometry of the dissolution reaction.
The solid does not appear explicitly in this expression because its activity is unity under the adopted pure-solid convention—not because solids are generally excluded from equilibrium expressions. For a solid solution or another phase whose component activities differ from unity, the relevant solid activity must be included. Hydrated solids also require care: if water appears in the balanced dissolution reaction, its activity belongs in the full equilibrium expression, although it is often approximated as unity in dilute aqueous solutions.
The connection to Gibbs free energy is
where is the standard Gibbs energy of the specified dissolution reaction, is the gas constant, and is absolute temperature. Thus, is a thermodynamic property of a defined reaction, solid phase, and set of standard states.
A logarithmic form is also used:
A larger means a smaller , but it does not by itself establish which of two salts has the smaller molar solubility.
Activities and concentration approximations
For a concentration-based standard state, the activity of a dissolved ion can be written as
where is its molar concentration, is the standard concentration, conventionally , and is its activity coefficient.
Consequently,
In sufficiently dilute solutions, activity coefficients may be approximated as unity. Textbooks therefore often write expressions such as
for silver chloride. This is shorthand: a thermodynamic equilibrium constant is dimensionless, whereas an unnormalized product of concentrations has units. A concentration product defined operationally can carry units and can vary with the solution medium.
Deviations from ideality depend strongly on ionic strength, which measures the concentrations of ions weighted by the squares of their charges. Adding an electrolyte that supplies no common ion can change a salt’s measured solubility through changes in activity coefficients, without changing its thermodynamic at fixed temperature and pressure.
Relationship to molar solubility
Molar solubility, , is the amount of a solid that dissolves per unit volume of solution. Unlike the solubility product, it depends not only on the dissolution equilibrium but also on the composition of the surrounding solution.
For dissolving in initially pure water, suppose that:
- dissolution is the only significant source of the constituent ions;
- the ions undergo no appreciable secondary reactions;
- the solution is dilute enough for ideal behavior.
Then
and
Thus,
A 1:1 salt
For silver chloride,
so that
Its molar solubility is therefore approximately .
A 1:2 salt
For calcium fluoride,
Since and ,
giving
These different relationships explain why solubility products cannot generally be compared as direct measures of molar solubility when salts have different dissolution stoichiometries.
Saturation and precipitation
The ion activity product, , has the same algebraic form as , but uses the activities present at any instant rather than necessarily at equilibrium. It is a particular reaction quotient.
For a specified solid phase:
- : the solution is undersaturated; dissolution of that solid is thermodynamically favored if it is present.
- : the solution is saturated with respect to that solid.
- : the solution is supersaturated; precipitation of that solid is thermodynamically favored.
For the dissolution reaction,
Supersaturation does not guarantee immediate precipitation. The formation of a new solid can be delayed by a nucleation barrier, slow crystal growth, or substances that inhibit growth. A supersaturated solution may therefore persist even though precipitation would lower its Gibbs energy. Solubility products describe equilibrium tendencies, not precipitation rates; those rates belong to chemical kinetics.
In geochemical calculations, saturation is often expressed as a saturation index:
Positive, zero, and negative values correspond to supersaturation, saturation, and undersaturation, respectively.
Effects of solution composition
Common-ion effect
The common-ion effect is the reduction in a salt’s solubility caused by adding another source of one of its constituent ions, when competing effects are negligible.
For silver chloride in a solution containing an initial chloride concentration , an idealized calculation gives
If ,
The common chloride ion lowers the free silver-ion concentration compatible with saturation. At high concentrations, however, activity effects and complex formation can make this simple relationship inadequate.
Acid–base reactions
The pH of a solution can strongly affect solubility when a constituent ion participates in an acid–base reaction. Protonation of carbonate, phosphate, sulfide, or other basic anions reduces the activity of the free anion appearing in the solubility-product expression. Further dissolution may then occur while the same remains satisfied.
For metal hydroxides, hydroxide activity is directly involved. For example,
with
At sufficiently high pH, some metals also form soluble hydroxide complexes, so their total dissolved concentrations need not decrease continuously as pH rises.
Complex formation
A ligand can bind a dissolved metal ion and reduce its free-ion activity. Additional solid may dissolve to restore saturation, increasing the total dissolved metal concentration without altering .
A familiar example is the dissolution of silver chloride in ammonia through formation of a soluble silver–ammonia complex. Such systems require simultaneous treatment of dissolution and complex-formation equilibria. The solubility product normally contains the free constituent ions, not the sum of their free and complexed forms.
Temperature and solid-phase dependence
Solubility products vary with temperature. Their temperature dependence is related to the standard dissolution enthalpy by the van ’t Hoff equation:
For an endothermic dissolution reaction, increases with temperature over a range in which the reaction enthalpy remains positive; for an exothermic reaction, it decreases. Changes in total solubility may be more complicated because secondary equilibria also depend on temperature.
The identity of the solid phase matters. Different crystal structures, hydrates, and amorphous forms of the same nominal composition can have different dissolution equilibria. Calcite and aragonite, for example, are distinct calcium carbonate phases and have different solubility products. Very small particles can also show size-dependent solubility because of surface contributions to their free energy.
Measurement, applications, and limitations
Solubility products can be determined by equilibrating a characterized solid with a solution, measuring the dissolved species, and applying an appropriate activity model. Accurate determination requires control of temperature, solution composition, solid-phase identity, and equilibration. When several dissolved forms are present, the calculation must distinguish free-ion activities from total analytical concentrations.
In analytical chemistry, solubility products underpin precipitation titrations, gravimetric analysis, and selective precipitation. Separation depends on whether one compound reaches saturation while others remain undersaturated; it cannot be judged from tabulated values alone.
In environmental chemistry and geochemistry, they are used to model mineral dissolution, contaminant retention, and precipitation in groundwater and other waters. Industrial uses include predicting scale formation and controlling precipitation during water treatment and materials processing.
The principal limitations arise from applying a simple equilibrium expression to a chemically or physically more complex system. Reliable calculations may require activity corrections, multiple coupled equilibria, mass and charge balances, and kinetic information. A reported value must therefore be interpreted together with its temperature, solid phase, standard-state convention, and whether it is a thermodynamic constant or a medium-dependent concentration product.