A simple machine is a basic mechanical device that changes the magnitude or direction of an applied force, usually by exchanging a greater input distance for a greater output force, or the reverse. The conventional six simple machines are the lever, wheel and axle, pulley, inclined plane, wedge, and screw. They do not supply energy: instead, they transmit energy from a person, animal, motor, or other source to a load. Their operation can be understood through classical mechanics, particularly the relationships among force, motion, rotation, and work.
Simple machines provide an enduring framework for understanding tools and machinery, from pry bars and ramps to cranes, presses, and threaded fasteners. The six-part classification developed historically rather than from a unique mathematical division of mechanisms. Several types are closely related: a pulley and a wheel and axle involve rotation, while wedges and screws use the geometry of inclined surfaces. Modern engineering treats them as elementary mechanisms whose useful performance depends not only on geometry but also on friction, material strength, deformation, and the way components are connected.
Mechanical advantage, work, and motion
The central quantitative idea is mechanical advantage, the ratio of useful output force to applied input force. If an effort produces a load force , the actual mechanical advantage is
A value greater than one indicates force multiplication. A value below one can nevertheless be useful: it may produce greater output speed or displacement, as in many tools and biological limb movements. A machine can also serve primarily to change force direction rather than magnitude. A fixed pulley, for example, allows a person to pull downward while a load rises.
For an ideal machine operating without losses or net accumulation of energy, input work equals output work. When forces are constant and measured along their respective displacements,
Consequently, the ideal mechanical advantage is
This expresses the essential trade-off: lifting a load with one-quarter of its weight as the effort requires the effort point to travel four times as far as the load. The machine reduces the required force, not the ideal amount of work. For varying forces, work must instead be calculated by integrating the component of force along the displacement.
The same relationship applies instantaneously to speeds. In an ideal mechanism with one independent input motion, the force ratio is the inverse of the corresponding speed ratio. The input point of a force-multiplying machine therefore moves faster than the output point. Mechanical power, the rate of doing work, remains equal at input and output in the lossless case. Real devices deliver less useful output power because some input energy becomes heat, sound, vibration, or deformation.
These relationships require a clearly defined operating condition. A machine accelerating a heavy load may temporarily store energy as kinetic energy, while a flexible component may store elastic potential energy. In such cases, input and useful output work need not match over an arbitrarily chosen interval even if dissipative losses are negligible. Elementary calculations generally assume slow motion or steady operation, rigid components, and negligible machine weight. Those assumptions isolate the geometric principle; they do not describe every force acting in an actual device.
Levers and rotational equilibrium
A lever is a substantially rigid member that turns about a support or pivot called a fulcrum. Its operation depends on torque, the turning effect of a force about an axis. For a force of magnitude , the torque magnitude is , where is the perpendicular distance between the axis and the force’s line of action. This perpendicular distance, rather than simply the length of the bar, is the relevant lever arm.
For an ideal lever in rotational equilibrium, with one effort and one load acting in opposite rotational senses,
Thus its ideal mechanical advantage is . An effort applied 0.80 metres from the pivot can ideally balance a load four times as large acting 0.20 metres from it, provided both distances are perpendicular moment arms. The fulcrum supplies an additional reaction force. It does no work if it remains stationary, but it can carry a substantial load that must be included in structural calculations.
Levers are conventionally divided into three classes according to the relative positions of fulcrum, effort, and load. In a first-class lever, the fulcrum lies between effort and load, as in a seesaw or a pry bar used over a support. Such a lever may multiply force or displacement depending on its proportions. In a second-class lever, the load lies between fulcrum and effort, as in the usual idealized model of a wheelbarrow: the wheel axle acts as the pivot, the carried material supplies the load, and the handles receive the effort. In the standard parallel-force arrangement, this geometry multiplies force.
In a third-class lever, the effort lies between fulcrum and load. Tweezers and many limb movements approximate this arrangement. When the forearm lifts an object through elbow flexion, a muscle acts relatively close to the elbow while the object is farther away. The muscle force can therefore greatly exceed the object’s weight, but the hand moves farther and faster than the muscle’s point of attachment. This is a useful displacement and speed advantage rather than an inefficient version of a force-multiplying lever.
Actual lever analysis must also account for the member’s own weight, distributed loads, and changing angles. A bar’s weight acts through its center of mass and may assist or oppose the applied effort. In mechanisms that rotate through a large angle, moment arms often vary throughout the stroke. The familiar ratio of two arm lengths is therefore exact only when the force directions and geometry justify that simplification.
Wheel and axle: coupling rotational motions
A wheel and axle consists of two coaxial rotating elements of different effective radii, rigidly connected so that they turn through the same angle. An effort applied tangentially at the larger radius can produce a larger tangential force at the smaller radius. A hand-operated windlass illustrates the arrangement: a handle turns a drum, and a rope wound around the drum lifts a load. The handle radius determines the input moment arm, while the drum radius determines the output moment arm.
For an ideal device, with effort applied at radius and load transmitted at radius ,
During one revolution, the effort point travels , while the rope moves . A handle radius of 0.30 metres and a drum radius of 0.05 metres therefore give an ideal force advantage of six. Raising a 600-newton load would require a 100-newton tangential effort under the stated ideal conditions. The effort point would travel six times the distance through which the load rises.
The same device can be driven in the opposite direction. Applying torque to the smaller element can make the larger rim move with greater tangential speed, although the available rim force decreases. Steering wheels, handwheels on valves, and screwdriver handles exploit a relatively large grip radius to generate torque at a smaller shaft. Their practical usefulness also depends on how comfortably the operator can apply force and how securely the hand contacts the surface.
A transport wheel requires a related but distinct explanation. A freely rotating wheel does not necessarily multiply a pulling force by the ratio of wheel radius to axle radius. Its principal benefit is often the substitution of rolling contact and bearing motion for sliding between the load and the ground. Resistance then depends on bearing losses, deformation of the wheel and surface, and obstacles. A larger wheel can pass over a given small step more readily than a smaller one, but this involves the geometry of contact and load support rather than the elementary windlass formula.
Real wheel-and-axle systems may also have a changing effective radius. As successive layers of rope accumulate on a drum, the load’s moment arm increases. For the same input torque, the available line pull consequently decreases, while the length wound per revolution increases. This is important in winches and cable reels. Bearing resistance, shaft bending, and the rotational moment of inertia further affect performance, especially during starting, stopping, or rapid changes in speed.
Pulleys and tensioned ropes
A pulley is a grooved wheel, or sheave, that guides a rope, cable, or belt. In elementary lifting systems, its most important functions are to redirect tension and to arrange several supporting rope segments around a moving load. A fixed pulley has an axis attached to a stationary support. Under ideal conditions, the rope tension is the same on both sides, so a single fixed pulley has a mechanical advantage of one. Its usefulness lies in changing the direction of effort.
A movable pulley travels with the load. If one end of a rope is anchored overhead, the rope passes under a movable pulley, and the free end is pulled upward, two rope segments support the moving assembly. In the ideal case, each carries tension , giving a total upward force of . The applied effort is , so the ideal mechanical advantage is two. Pulling two metres of rope raises the moving assembly by one metre.
A block and tackle combines multiple sheaves in fixed and moving blocks. In a common ideal arrangement, the mechanical advantage equals the number of rope segments effectively supporting the moving assembly. A six-part supporting arrangement can therefore provide an ideal mechanical advantage of six. The number of wheels alone is not enough to determine this ratio: the location of the anchored rope end, the path of the rope, and which block moves are all essential. Forces must be resolved along their actual directions if the supporting segments are not parallel.
The elementary treatment assumes a massless, inextensible rope and freely rotating, massless sheaves. Real ropes stretch and have weight; real sheaves require torque to overcome bearing resistance and to bend the rope around the groove. Tensions can consequently differ across a sheave during motion. Adding more supporting parts reduces the ideal effort but also lengthens the rope that must be hauled and introduces additional losses. For a heavy moving block, some of the supporting force lifts the apparatus itself rather than the useful payload.
Pulley principles also appear in cranes, elevators, sailing equipment, and theatre rigging, although these systems often include counterweights, powered drums, brakes, and control mechanisms. A traction elevator, for example, cannot be reduced to a freely turning fixed pulley: the drive sheave transmits force through frictional contact with the suspension members. Such applications show why the distinction between a guiding sheave, a force-multiplying tackle, and a powered traction element matters when interpreting an actual machine.
Inclined planes and controlled elevation
An inclined plane allows a load to rise through a given vertical height while moving along a longer sloping path. Let the slope length be , its vertical rise be , and its angle above the horizontal be . Since , an ideal frictionless load of weight , moved steadily by an effort parallel to the slope, requires
The ideal mechanical advantage is therefore
The force reduction follows from resolving the load’s weight into components parallel and perpendicular to the plane. The surface supports the perpendicular component through a normal reaction. In the ideal rigid model, this reaction does no work because the load’s motion is parallel to the surface. The effort supplies the increase in gravitational potential energy, , regardless of how long the ramp is. A longer ramp lowers the required force but increases the distance over which it acts.
For example, raising a 1,000-newton load by one metre along a five-metre frictionless ramp requires a constant parallel effort of 200 newtons. Both a direct vertical lift and the ramp require 1,000 joules of ideal work. The ramp changes how that work is delivered. This is particularly useful when the available force is limited but a longer movement is practical, as in loading ramps, access ramps, and sloping transport routes.
Sliding friction modifies this result. With a coefficient of kinetic friction , and with the applied effort still parallel to the plane, the normal force is . The force required for steady upward sliding becomes
Under this simplified model, frictional work over a slope of length is . Making the slope progressively shallower therefore does not reduce the effort toward zero when sliding friction remains significant. Rolling loads require a different resistance model, since wheel deformation and bearing losses cannot generally be represented by the same sliding-friction coefficient.
The direction of the applied force also matters. A horizontal push has both a component up the slope and a component pressing the object into it, changing the normal reaction and friction. Likewise, a load at rest is governed by static friction, which adjusts up to a limiting value rather than always equalling that value. These distinctions make the inclined plane an important model for force diagrams, equilibrium, and the transition between rest and motion.
Wedges, cutting, and separating forces
A wedge is a tapered body that converts motion along its length into displacement and force transverse to that motion. Unlike the usual fixed-ramp arrangement, the inclined surface itself advances into or beneath the load. Doorstops, splitting wedges, chisels, and many cutting edges use this geometry, although their detailed behavior differs considerably. A wedge can lift, separate, locate, or hold objects, depending on the constraints around it.
A simple ideal model is a single-sided wedge with a horizontal base and an upper surface inclined at angle . Suppose it advances horizontally beneath a vertically guided load, with all contacts frictionless. A horizontal advance raises the load by . Conservation of work then gives
so
For a wedge of horizontal length and rise , this becomes . A thin wedge can therefore generate a large lifting force from a smaller driving force, at the cost of requiring substantial insertion distance.
A symmetric splitting wedge has two inclined faces, and its force accounting must distinguish the force on each side from the combined separating action. If each face makes an angle with the direction of advance, the frictionless normal reactions have axial components that resist insertion and transverse components that push the material apart. A thinner wedge produces a larger transverse force relative to the axial driving force. Quoting a single mechanical-advantage ratio without defining the output force and displacement can therefore be misleading.
Practical wedges are strongly affected by friction and material deformation. Friction opposes both insertion and withdrawal, reducing the force multiplication available during insertion but sometimes helping the wedge remain in place. A doorstop works largely because contact friction prevents it from being expelled under load. In a splitting tool, meanwhile, the surrounding material may crack, bend, crush, or tear. The input work includes the energy associated with these processes, not merely reversible lifting against a fixed load.
Cutting edges also concentrate force over a small contact area, producing high local pressure and stress. A sharp blade generally initiates cutting more readily than a blunt one, but blade angle, edge radius, toughness, and wear resistance impose competing requirements. A very thin edge can chip or bend under conditions that a thicker edge survives. Consequently, the geometry of an ideal wedge explains part of cutting action, while fracture mechanics and the properties of the material being cut explain why different tools require different edge shapes.
Screws and helical motion
A screw uses a helical surface to couple rotation with axial displacement. Its elementary geometry can be represented by wrapping an inclined plane around a cylinder. One revolution advances a mating component through a distance called the lead. The pitch is the axial spacing between adjacent corresponding thread forms. For a single-start thread, lead and pitch are equal; for a thread with starts, the lead is times the pitch.
If an effort acts tangentially at handle radius , it supplies torque . During one revolution, the input work is . If the axial load is and the lead is , ideal output work is . Thus
A small lead combined with a long handle can generate very large axial forces, explaining the effectiveness of screw jacks, bench vises, and screw presses.
For example, a handle radius of 0.20 metres and a lead of 0.005 metres give an ideal force ratio of about 251. A 100-newton tangential effort would then correspond to an ideal axial force of roughly 25,100 newtons. This calculation is not a load rating. Actual capacity may be much lower because of thread friction, bearing resistance, thread stripping, shaft buckling, or other structural limits. The ideal result describes the work ratio associated with the geometry.
Friction is especially important in screws because sliding occurs along the thread surfaces, often under high contact loads. In a simplified square-thread model, self-locking depends on the relationship between the thread’s lead angle and the effective friction angle. If friction is sufficient, an axial load cannot drive the screw backward without an externally applied torque. This is valuable in holding and clamping devices. Conversely, ball screws use rolling elements to reduce losses and can often be back-driven by an axial load unless an additional restraint is present.
Threaded fasteners introduce further behavior beyond the elementary lifting model. Tightening a bolt usually stretches the bolt and compresses the joined parts, creating a clamping preload. Much of the applied torque is consumed by friction in the threads and under the rotating bearing surface. Torque therefore does not translate into a unique clamping force without information about lubrication, geometry, surface condition, and material response. Precision lead screws and micrometers use the same rotation-to-translation principle for controlled positioning rather than primarily for force multiplication.
Efficiency, friction, and structural limits
The efficiency of a machine is the ratio of useful output work to input work:
For constant forces over corresponding input and output strokes,
If a lifting arrangement has an ideal mechanical advantage of five but an actual advantage of four under a specified operating condition, its efficiency for that operation is 0.80, or 80 percent. Force ratios alone cannot establish efficiency unless the associated displacement ratio is also known.
Losses arise through several mechanisms. Sliding contacts generate heat; bearings resist rotation; flexible ropes dissipate energy as they bend and straighten; and components can vibrate or undergo internal damping. Lubrication, suitable bearings, larger sheave diameters, and appropriate surface finishes may reduce particular losses, but their effects depend on load, speed, temperature, and contamination. A single fixed efficiency is therefore often only an approximation to a device’s behavior over a limited operating range.
Friction is not always an unwanted defect. It allows a wedge to stay seated, a screw to hold a load, and a traction drive to transmit force. Static friction at an ideal stationary contact need not dissipate energy, because the contacting surfaces do not slide relative to each other. Energy dissipation becomes associated with sliding, deformation, or other irreversible processes. Confusing the presence of frictional force with an automatic loss of work obscures the operation of many useful mechanisms.
Structural capacity is separate from mechanical advantage. A lever with a very long effort arm may bend or break; a slender screw may buckle; a rope may fail in tension; and a pulley axle may overload its support. The machine’s theoretical ability to multiply force says nothing by itself about the maximum safe load. Material properties, geometry, joints, wear, fatigue, and manufacturing defects all influence the forces that an actual component can sustain.
Dynamic operation introduces additional limits. Accelerating a load requires a net force according to Newton’s laws of motion, and accelerating rotating parts requires torque associated with their rotational inertia. Impacts can produce brief forces much larger than those predicted from steady equilibrium. A dropped load caught by a rope, for example, involves energy absorption and elastic extension rather than simply a static multiplication of the load’s weight. Engineering analysis therefore distinguishes ideal kinematics, steady force transmission, energy losses, and structural response.
Compound machines and connected mechanisms
A compound machine combines two or more elementary mechanisms. Scissors join two first-class levers at a common pivot, while their sharpened blades provide wedge-like cutting action. A wheelbarrow combines a lever arrangement with a rolling wheel. A screw jack combines a rotating handle or geared drive with a screw that produces axial motion. The familiar six simple machines are consequently best understood as analytical building blocks, not mutually exclusive labels for complete objects.
When ideal stages act in series, their mechanical advantages multiply, provided that the output force and displacement of one stage are correctly matched to the input of the next. A lever with a force ratio of three driving a lifting arrangement with a ratio of four can, in an appropriate configuration, produce an overall ideal ratio of twelve. The total input travel is correspondingly twelve times the final output travel. This multiplication does not create an energy surplus; it compounds the exchange between force and distance.
Efficiencies also combine. If two stages transmit useful work in sequence with efficiencies and , and neither changes its stored energy over the interval, their combined efficiency is
Two stages each operating at 90 percent efficiency would yield 81 percent overall. Additional stages can make a load manageable while also increasing losses, mass, cost, compliance, and the number of components subject to wear. The best arrangement therefore depends on more than the largest attainable force ratio.
Gears provide an important extension of the wheel-and-axle principle. Meshing teeth constrain the relative rotations of two wheels. In an ideal gear pair, the angular-speed ratio is inversely proportional to the tooth-count ratio, while the torque ratio changes in the opposite way. Gears can transmit motion between different axes, reverse direction, and supply a nearly constant velocity ratio. Their detailed geometry and contact behavior go beyond the traditional six-machine classification, but their work balance follows the same principles.
Many mechanisms have a mechanical advantage that changes continuously with position. Linkages, toggle clamps, and cam-operated devices can produce large forces near particular configurations. An ideal toggle mechanism approaching alignment may have a very large calculated force ratio, but the available movement becomes very small, and deformation and clearances become decisive. More generally, for a lossless mechanism with input coordinate and output coordinate , the local relationship is
This differential form connects elementary machines to the broader study of kinematics and mechanism design, where geometry determines how motions and forces change throughout an operating cycle.
Historical development and the six-machine classification
The practical devices now grouped as simple machines appeared long before a unified theory of mechanics. Levers, wedges, and inclined surfaces were used in construction and craft traditions without necessarily being described as members of a common category. Their early histories are difficult to reduce to single inventions: a sharpened stone, a wooden lifting bar, and a sloping earthwork can embody relevant mechanical principles without sharing a documented theoretical explanation. Archaeological evidence establishes particular uses, but it does not identify one inventor of “the simple machine.”
In the mathematical traditions of ancient Greece, the lever became a central object of theoretical investigation. Archimedes, who lived approximately from 287 to 212 BCE, developed propositions concerning equilibrium in On the Equilibrium of Planes. His work connected weights and distances in a mathematical treatment of balance. Ancient accounts also associate him with powerful lifting arrangements, although later anecdotes should be distinguished from the surviving mathematical arguments.
Hero of Alexandria, active in the first century CE, discussed lifting devices in his Mechanics. The ancient mechanical tradition commonly treated five principal powers: the lever, windlass, pulley, wedge, and screw. The familiar modern list of six, with the inclined plane explicitly included, was not simply a classification transmitted unchanged from antiquity. It emerged through later efforts to compare machines and explain their shared principles. Ancient and medieval mechanical knowledge also developed through practical construction, commentary, translation, and the adaptation of devices to local tasks.
During the Renaissance, illustrated machine books and mathematical investigations brought mechanisms into closer contact with systematic analysis. Simon Stevin’s De Beghinselen der Weeghconst, published in 1586, included a celebrated argument for equilibrium on inclined planes using an imagined endless chain. The chain would otherwise move perpetually under its own weight, so its balance could be used to infer relationships between forces on differently inclined surfaces. This helped make the inclined plane a subject of rigorous statics rather than merely a practical construction device.
Galileo Galilei, in writings on mechanics dating from the 1590s, emphasized that machines do not overcome nature by producing a gain without compensation: an advantage in force corresponds to an increased distance of action. Later formulations of work, energy, and virtual work supplied a more general mathematical language for this relationship. Nineteenth-century engineering incorporated friction, efficiency, materials, and power transmission into increasingly detailed machine theory. The six simple machines retained a prominent educational role because they make force–motion trade-offs visible, while professional mechanics extended the analysis to mechanisms that do not fit neatly into the traditional list.