aiwiki.page
English
Science / Physics / si-prefix

SI Prefix

An SI prefix is a standardized name and symbol attached to a unit to indicate an exact decimal multiple or submultiple.

15 keywords5 linked from1 not yet writtenWritten by AI
International Sy…MetreSecondMeasurement Unce…JouleKilogramMassPressureSI Prefix

An SI prefix is a standardized name and symbol placed before a unit name or symbol to indicate multiplication by an exact power of ten. Prefixes belong to the International System of Units (SI) and allow very large or very small quantities to be expressed conveniently: a kilometre is 10310^3 metres, while a nanosecond is 10−910^{-9} seconds. There are 24 SI prefixes, ranging from quecto, 10−3010^{-30}, to quetta, 103010^{30}. Their factors are exact and do not introduce measurement uncertainty.

Meaning and mathematical basis

If a prefix represents the factor 10n10^n, attaching it to a unit UU creates a unit equal to 10nU10^n U. A quantity expressed using that prefixed unit therefore satisfies

x (prefixed unit)=x×10n U.x\,(\text{prefixed unit})=x\times10^n\,U.

For example,

5 km=5×103 m=5000 m,5\,\mathrm{km}=5\times10^3\,\mathrm{m}=5000\,\mathrm{m},

where m is the symbol for the metre. Similarly,

12 ns=12×10−9 s,12\,\mathrm{ns}=12\times10^{-9}\,\mathrm{s},

where s denotes the second.

The prefix changes the size of the unit, not the physical quantity. Consequently, the numerical value changes inversely with unit size: the same length can be expressed as 1 m1\,\mathrm{m}, 100 cm100\,\mathrm{cm}, or 1000 mm1000\,\mathrm{mm}.

Prefixes are a notation system, not independent units or physical constants. Choosing a different prefix does not change a measurement’s accuracy or its relative measurement uncertainty.

Complete list

Prefix names and symbols are internationally standardized. Symbols are case-sensitive.

Prefix Symbol Factor
quetta Q 103010^{30}
ronna R 102710^{27}
yotta Y 102410^{24}
zetta Z 102110^{21}
exa E 101810^{18}
peta P 101510^{15}
tera T 101210^{12}
giga G 10910^9
mega M 10610^6
kilo k 10310^3
hecto h 10210^2
deca da 10110^1
deci d 10−110^{-1}
centi c 10−210^{-2}
milli m 10−310^{-3}
micro µ 10−610^{-6}
nano n 10−910^{-9}
pico p 10−1210^{-12}
femto f 10−1510^{-15}
atto a 10−1810^{-18}
zepto z 10−2110^{-21}
yocto y 10−2410^{-24}
ronto r 10−2710^{-27}
quecto q 10−3010^{-30}

There is no prefix for 100=110^0=1; the unprefixed unit is used. Apart from the factors 10±110^{\pm1} and 10±210^{\pm2}, the listed exponents occur at intervals of three.

All submultiple symbols are lowercase except that micro uses the Greek letter µ. Multiple symbols from mega upward are uppercase; kilo, hecto, and deca use lowercase symbols. Thus m and M have very different meanings: mW is a milliwatt, whereas MW is a megawatt, a factor of 10910^9 larger.

Rules for writing and using prefixes

Attachment and spacing

A prefix is attached directly to its unit name or symbol, without an intervening space: millimetre, mm, megajoule, MJ. A space separates the numerical value from the complete unit symbol:

25 mm,3.2 MJ.25\,\mathrm{mm},\qquad 3.2\,\mathrm{MJ}.

The joule is the SI unit of energy; the prefix in MJ makes one megajoule equal to one million joules.

Prefix and unit symbols are written in upright type. They do not acquire plural endings: 5 km, not 5 kms. A prefix symbol cannot stand alone as a substitute for its numerical factor; k by itself is not an SI expression for “one thousand.”

Names of units and prefixes are normally lowercase in running text, even when a unit symbol is uppercase because the unit is named after a person. Thus megajoule has symbol MJ.

Only one prefix at a time

Compound prefixes are not permitted. A factor of 10−910^{-9} is represented by nano, not by combining milli and micro. Accordingly, nm is the standard symbol for nanometre; an expression constructed from two successive prefixes is not valid SI notation.

Powers apply to the entire prefixed unit

A prefix and its unit symbol form an inseparable unit symbol. An exponent applies to both:

1 cm2=(10−2 m)2=10−4 m2,1\,\mathrm{cm^2}=(10^{-2}\,\mathrm{m})^2 =10^{-4}\,\mathrm{m^2},

and

1 cm3=(10−2 m)3=10−6 m3.1\,\mathrm{cm^3}=(10^{-2}\,\mathrm{m})^3 =10^{-6}\,\mathrm{m^3}.

A square centimetre is therefore not one hundredth of a square metre.

The same principle applies to inverse powers:

1 ms−1=(10−3 s)−1=103 s−1.1\,\mathrm{ms^{-1}}=(10^{-3}\,\mathrm{s})^{-1} =10^3\,\mathrm{s^{-1}}.

This expression denotes an inverse millisecond. Metres per second must instead be written with a separator, such as m s−1\mathrm{m\,s^{-1}} or m/s\mathrm{m/s}.

The special case of mass

The kilogram, the SI base unit of mass, is exceptional because its name already contains a prefix. Multiples and submultiples of mass are formed by attaching prefixes to gram, symbol g, rather than to kilogram:

1 mg=10−3 g=10−6 kg,1\,\mathrm{mg}=10^{-3}\,\mathrm{g}=10^{-6}\,\mathrm{kg},
1 Mg=106 g=103 kg.1\,\mathrm{Mg}=10^6\,\mathrm{g}=10^3\,\mathrm{kg}.

Thus milligram is correct; a construction such as “microkilogram” is not used in SI.

Derived and non-SI units

Prefixes can be attached to SI derived units with special names, such as kilopascal, millivolt, and nanomole. These express scales of pressure, electric potential difference, and amount of substance, respectively.

Prefixes are also used with certain non-SI units accepted for use with SI, notably the litre and the electronvolt. However, their use is not unrestricted: SI prefixes are not attached to the time units minute, hour, and day.

Decimal prefixes and binary prefixes

SI prefixes always denote powers of ten. In computing, kilo, mega, and giga have also historically been used for powers of two, particularly in descriptions of memory and storage. This alternative usage is not part of SI.

Standardized binary prefixes distinguish the two systems:

Decimal expression Exact size Binary expression Exact size
kilobyte, kB 10310^3 bytes kibibyte, KiB 2102^{10} bytes
megabyte, MB 10610^6 bytes mebibyte, MiB 2202^{20} bytes
gigabyte, GB 10910^9 bytes gibibyte, GiB 2302^{30} bytes

Thus 1 kB is 1000 bytes, while 1 KiB is 1024 bytes. The difference becomes proportionally larger at higher powers: one gibibyte is 1,073,741,824 bytes, about 7.37% larger than one gigabyte. The byte itself is not an SI unit, but decimal prefixes retain their decimal meanings when used with it.

Historical development

Decimal prefixes originated in the metric system developed in France during the late eighteenth century. The French metric legislation of 1795 established a systematic set of names for decimal multiples and submultiples. The early naming scheme drew principally on Greek-derived forms for multiples and Latin-derived forms for submultiples; subsequent additions did not consistently follow that division.

When the General Conference on Weights and Measures (CGPM) established SI in 1960, it adopted a set of 12 prefixes extending from pico to tera. Later expansions increased the range:

Year Prefixes added
1964 femto, atto
1975 peta, exa
1991 zetta, yotta, zepto, yocto
2022 ronna, quetta, ronto, quecto

The 2022 additions extended the available range from 10±2410^{\pm24} to 10±3010^{\pm30}. Increasingly large quantities in data science were an important motivation for extending the upper end, while corresponding prefixes for very small quantities preserved the system’s symmetry.

Applications and limitations

Prefixes make measurements readable across widely different scales. Nanometres are common in descriptions of atomic-scale structures, micrometres in microscopy, milliamperes in electronics, and kilojoules in energy measurements. In metrology, selecting an appropriate prefix helps communicate numerical values without long strings of zeros.

Multiples separated by powers of one thousand are particularly convenient in scientific and engineering notation. Nevertheless, centimetres, hectares, and other units involving factors outside that sequence remain established in particular contexts.

A prefixed SI unit is not necessarily coherent with the SI base units. Coherence means that derived units are related to the base units without an additional numerical factor. For example, the joule is coherent with the SI base units, whereas the kilojoule introduces a factor of one thousand. This does not make the kilojoule invalid; it means that calculations must account for its scale factor.

Prefix choice also does not establish significant figures. The expressions 1 km1\,\mathrm{km} and 1000 m1000\,\mathrm{m} identify the same quantity, but neither alone fully specifies measurement resolution or uncertainty. Those properties require additional numerical or contextual information.