Saltation is a mode of sediment transport in which particles move in repeated short hops above a bed, returning to the surface between successive movements. It occurs when wind or flowing water sets grains in motion, accelerates them during their trajectories, and causes them to rebound or dislodge other particles on impact. Saltation is especially important in the movement of windblown sand, but it also transports sediment along riverbeds and coastal seabeds. It connects fluid motion, grain collisions, and changes in surface landforms.
Relationship to other transport modes
Sediment transport is commonly divided into several modes, although their boundaries are gradual rather than absolute:
- Rolling and sliding: grains remain in frequent or continuous contact with the bed.
- Saltation: grains leave the bed in distinct hops and return to it repeatedly.
- Suspension: particles remain within the fluid for extended periods because turbulent motions counteract their tendency to settle.
In water, saltation, rolling, and sliding are generally included within bed load, meaning sediment transported close to the bed through frequent interactions with it. Classification depends partly on the observation scale: an individual grain may alternate between rolling, hopping, and suspension as local flow conditions change.
Grain size alone does not determine the transport mode. Particle density, shape, fluid density and viscosity, bed roughness, and flow strength all matter. Sand commonly saltates in air, whereas finer dust is more readily carried in suspension once released. In rivers, sand or gravel may saltate under suitable conditions, while the same material may remain stationary in weaker flows or enter suspension in stronger ones.
Physical mechanism
Initiation of motion
A resting grain begins to move when fluid forces and moments overcome the stabilizing effects of its submerged weight, contacts with neighboring grains, and any cohesive forces. The grain may initially roll or pivot out of its resting position before entering a hop.
Flow strength near the bed is often represented by the friction velocity:
where is the fluid shear stress at the bed and is fluid density. Friction velocity has the dimensions of speed but is a measure of shear stress, not the actual velocity of a grain or of the fluid at a particular height.
For relatively coarse, noncohesive grains, increasing grain size generally increases the stress needed for movement. For very fine particles, cohesion can also raise the threshold, so progressively smaller particles are not necessarily easier to entrain. Moisture, surface crusts, vegetation, and the sheltering of grains behind larger particles further modify the threshold.
Flight and impact
Once airborne or lifted into water, a grain follows a trajectory governed by gravity, fluid drag, and other fluid forces. Its path resembles a ballistic arc only approximately, because the surrounding flow continues to accelerate or decelerate it.
On striking the bed, a grain can:
- rebound into another hop;
- stop and become part of the resting bed;
- eject other grains in a process called splash;
- push neighboring particles into short hops, rolling, or sliding.
The repeated exchange between moving and resting particles makes saltation a population process rather than simply a series of independent projectile motions.
Feedback with the flow
Saltating grains extract momentum from the fluid. As particle transport increases, the near-bed flow is modified, affecting further entrainment and particle acceleration. Transport therefore depends both on the force exerted by the fluid and on the response of the moving grains and sediment bed.
If sediment is available and the flow persists over sufficient distance, transport may approach a statistically steady state. Following a change in wind or water velocity, however, the moving sediment population requires a finite distance and time to adjust. This adjustment is important in the development of ripples and dunes.
Wind-driven saltation
Saltation is a central mechanism of aeolian sediment transport across deserts, beaches, dry agricultural soils, and other exposed surfaces. Most windblown sand travels close to the ground, although hop dimensions vary substantially with grain properties, wind conditions, and surface characteristics.
A distinctive feature of aeolian saltation is the importance of impact-driven entrainment. Once transport has begun, grains striking a loose sand bed can eject replacements. Consequently, the wind strength needed to sustain established saltation can be lower than that needed to initiate it directly from a resting bed. These are commonly distinguished as the impact threshold and the fluid threshold. The difference produces hysteresis: whether transport occurs at a given wind strength can depend on whether grains were already moving.
Wind-driven saltation also mobilizes particles that do not themselves travel mainly by saltation:
- Impacts can drive larger grains into short movements known as reptation or surface creep.
- Impacts on soil aggregates can release fine particles into the atmosphere, linking saltation to dust emission.
This distinction is important because atmospheric dust need not have been lifted directly from rest by aerodynamic forces. Bombardment by saltating sand can provide the energy needed to detach it.
Saltation in flowing water
In rivers, tidal channels, and wave-agitated coastal settings, saltation is part of near-bed sediment movement. Turbulent fluctuations, particle exposure, and collisions with the bed all affect entrainment and hop length.
Water is much denser than air, so buoyancy, fluid drag, and the fluid response to particle motion have greater relative importance. Although impacts and rebounds occur, the strongly splash-maintained behavior characteristic of windblown sand cannot simply be assumed for underwater transport.
The initiation of noncohesive sediment motion in water is often analyzed using the Shields parameter:
where is sediment density, is gravitational acceleration, and is a representative grain diameter. This dimensionless ratio compares bed shear stress with a measure of submerged grain weight. Its critical value depends on flow and bed conditions; it is not a universal constant. Nor does exceeding the threshold specify whether grains will roll, saltate, or become suspended.
Under sufficiently intense transport, individual hops may become difficult to distinguish within a dense moving sediment layer. At higher turbulent intensities, particles can spend longer intervals in suspension.
Geomorphic and environmental significance
Saltation contributes to landform development by redistributing sediment and concentrating impacts near the surface.
Ripples and dunes. Differences in erosion, deposition, grain trajectories, and flow over uneven surfaces generate and modify bedforms. Impact-driven sorting is especially important for many wind ripples. The growth and migration of larger sand dunes also depend on interactions between sediment flux and airflow.
Abrasion. Repeated impacts can wear exposed rock, damage plant tissues, and abrade structures. Windblown sand often produces its strongest abrasive effects near the ground, where moving grains are concentrated.
Soil loss and dust production. On dry, exposed soils, saltation contributes directly to soil erosion and can release finer material for long-distance atmospheric transport. Its intensity depends on surface cover, moisture, aggregation, and the supply of erodible particles.
Sediment redistribution. In rivers and coastal environments, saltating grains contribute to bed-load flux, grain sorting, and the adjustment of channels and beaches. Their movement is one component of a broader sediment budget, rather than a complete description of sediment transfer.
Study and modeling
Modern experimental study of aeolian saltation was strongly advanced by Ralph Alger Bagnold, whose 1941 book The Physics of Blown Sand and Desert Dunes established influential descriptions of windblown sand transport.
Saltation is investigated using wind tunnels, water flumes, sediment traps, impact sensors, and high-speed imaging. Particle-tracking methods measure hop lengths, heights, velocities, and collision behavior. Numerical models range from empirical transport equations to simulations that couple fluid flow with the motion and collisions of individual grains.
Important limitations include the difficulty of measuring very short hops, separating saltation from rolling and suspension, and transferring laboratory results to heterogeneous natural surfaces. Transport rates also depend on sediment supply: strong flow over a crusted, vegetated, or sediment-depleted surface need not produce the flux predicted for a deep bed of loose sand. Consequently, saltation equations require attention to their threshold definitions, measurement methods, and range of applicable surface and flow conditions.