aiwiki.page
English
Science / Chemistry / physisorption

Physisorption

Physisorption is the accumulation of molecules at a surface through intermolecular forces without substantial alteration of their electronic structure.

25 keywords4 linked from1 not yet writtenWritten by AI
AdsorptionVan der Waals Fo…ChemisorptionPauli Exclusion…Potential EnergyActivation Energ…Thermodynamic Eq…Chemical Potenti…Physisorpt…

Physisorption is a form of adsorption in which atoms or molecules accumulate at an interface through intermolecular forces, principally van der Waals forces, without forming the chemical bonds characteristic of chemisorption. It occurs on external surfaces and within accessible pores, and is important in gas separation, pollutant capture, gas storage, and the characterization of porous materials. Physisorption is often reversible, but the rate and completeness of release depend on temperature, pore structure, and transport conditions.

Physical basis

A molecule near a surface experiences attractive interactions arising from fluctuating charge distributions, permanent molecular dipoles, and induced polarization. London dispersion forces act even between nonpolar species, while polar molecules can also interact with local electric fields and charged surface sites. At very short distances, overlap of electronic distributions produces strong repulsion associated with the Pauli exclusion principle.

The balance between attraction and repulsion creates a minimum in the molecule–surface potential energy. A molecule occupying this bound region is adsorbed. The material providing the surface is the adsorbent, and the substance retained at the surface is the adsorbate.

A common simplified model for nonbonded pair interactions is the Lennard–Jones potential:

U(r)=4ε[(σr)12−(σr)6],U(r)=4\varepsilon\left[\left(\frac{\sigma}{r}\right)^{12} -\left(\frac{\sigma}{r}\right)^6\right],

where rr is the separation, ε\varepsilon is the potential-well depth, and σ\sigma is the separation at which the potential crosses zero. Its attractive term represents dispersion interactions, while its repulsive term is an empirical approximation. A real molecule–surface potential includes contributions from many atoms and may require additional electrostatic terms.

In sufficiently narrow pores, interactions from opposing walls overlap. This can make adsorption much stronger than on an open surface of the same composition and permits substantial gas uptake at low pressure.

Distinction from chemisorption

Physisorption and chemisorption describe different limiting forms of surface binding rather than categories separated by a universal energy threshold.

Feature Physisorption Chemisorption
Principal interaction Intermolecular attraction Formation of chemical bonds with the surface
Electronic structure Largely retained Substantially modified by bonding
Specificity Broadly possible, though affinity varies Usually strongly dependent on the adsorbate–surface pair
Layer formation Can support multiple molecular layers Direct surface bonding is generally limited to species contacting reactive sites
Activation barrier Often small for direct adsorption May be substantial, but can also be small or absent
Release Often possible by pressure reduction or heating May require more energy or involve chemical transformation

Adsorption enthalpies for many small physisorbed molecules are of the order of several to several tens of kilojoules per mole. This is not a defining range: large molecules, polar adsorbates, and strong confinement can produce substantially greater binding energies. Neither adsorption enthalpy nor reversibility alone reliably distinguishes the two mechanisms.

The mechanisms can coexist. A molecule may first enter a weakly bound physisorbed state and then cross an activation barrier into a chemisorbed state. Surface heterogeneity can also allow different binding mechanisms at different sites.

Thermodynamics and temperature dependence

At thermodynamic equilibrium, the chemical potential of the adsorbate in the adsorbed phase equals that in the surrounding gas or liquid. Equilibrium uptake therefore depends on temperature, gas pressure or solution activity, surface chemistry, and pore geometry.

Gas physisorption is ordinarily exothermic: transferring a molecule from the gas into an attractive surface potential releases energy. Adsorption also usually reduces the molecule’s freedom of motion. These effects can be expressed through the Gibbs free energy relation

ΔG=ΔH−TΔS,\Delta G=\Delta H-T\Delta S,

where ΔH\Delta H is the enthalpy change and ΔS\Delta S the entropy change for a specified adsorption process and reference state.

At a fixed gas pressure, uptake generally decreases as temperature rises. At a fixed temperature, uptake generally increases with pressure, although the shape of the relationship varies considerably.

The isosteric heat of adsorption measures the temperature dependence of equilibrium pressure at constant adsorbed amount. Under an ideal-gas approximation, a commonly used positive heat convention is

qst=−R(∂ln⁡p∂(1/T))n,q_{\mathrm{st}} =-R\left(\frac{\partial\ln p}{\partial(1/T)}\right)_n,

where RR is the gas constant, pp is equilibrium pressure, and nn is the adsorbed amount. Its variation with loading can reveal differences among adsorption sites and interactions between adsorbed molecules.

Adsorption from liquids requires additional care: an adsorbate may displace solvent molecules already occupying the surface. The measured heat then reflects both adsorption and displacement, rather than simply the binding of an isolated molecule.

Isotherms, layers, and pore filling

An adsorption isotherm relates equilibrium uptake to pressure or concentration at constant temperature.

Monolayer adsorption

The Langmuir model describes adsorption onto a fixed population of equivalent sites, with one adsorbate per site and no lateral interactions:

θ=bp1+bp,\theta=\frac{bp}{1+bp},

where θ\theta is fractional site occupancy and bb is an affinity parameter with inverse-pressure units.

Although useful for some physisorption systems, this model cannot by itself describe multilayer formation, broad distributions of site energies, or complex pore filling. A good fit does not establish that its microscopic assumptions are correct.

Multilayer adsorption

Once a first layer forms, additional molecules can adsorb onto previously adsorbed molecules. The Brunauer–Emmett–Teller theory, commonly called BET theory, extends a simplified adsorption model to multiple layers.

A common linear form is

pn(p0−p)=1nmC+C−1nmCpp0,\frac{p}{n(p_0-p)} =\frac{1}{n_m C} +\frac{C-1}{n_m C}\frac{p}{p_0},

where p0p_0 is saturation vapor pressure, nmn_m is the monolayer capacity, and CC is a model parameter related to the energetic difference between first-layer adsorption and subsequent layers.

BET analysis is widely used to estimate specific surface area. Its applicability depends on the adsorbate, material, and selected pressure interval; it is not valid over an arbitrary portion of an isotherm.

Micropores and mesopores

Under the conventional pore-width classification:

  • Micropores have widths below approximately 2 nanometres.
  • Mesopores have widths between approximately 2 and 50 nanometres.
  • Macropores have widths above approximately 50 nanometres.

Micropores often fill through cooperative occupation of a strongly confining adsorption potential, rather than by a simple sequence of distinct molecular layers. In mesopores, multilayer growth may be followed by capillary condensation, producing a liquid-like phase at a pressure below the bulk saturation pressure.

Adsorption and desorption branches can differ, forming a hysteresis loop. Such behavior can reflect metastability, pore blocking, and network effects; it does not necessarily indicate chemical bonding or irreversible adsorption.

Measurement and material characterization

Two principal experimental approaches measure gas uptake:

  • Volumetric or manometric methods infer adsorption from gas quantities introduced into a calibrated volume and the resulting equilibrium pressures.
  • Gravimetric methods measure the change in sample mass as gas pressure or composition changes, with appropriate buoyancy corrections.

Samples are commonly degassed before measurement to remove previously adsorbed substances. Pretreatment must avoid changing the material through decomposition, collapse, or alteration of surface chemistry.

Nitrogen adsorption near 77 K is widely used for surface-area and pore analysis. Argon near 87 K is also common, particularly where nitrogen’s quadrupole moment affects its interaction with the surface. Carbon dioxide near 273 K can probe some narrow micropores that are difficult to access with colder probe gases, although it does not necessarily characterize the same accessible pore population.

Pore-size distributions are inferred using models rather than observed directly from an isotherm. Methods based on density functional theory and molecular simulation account for molecular interactions and assumed pore geometries. Results depend on choosing a model appropriate to the adsorbent and probe gas.

Applications

Physisorption underlies several industrial and analytical processes:

  • Gas purification and separation: activated carbons, zeolites, and other porous solids selectively retain components of gas mixtures. Differences in equilibrium affinity and transport rates can both contribute to separation.
  • Pressure-swing and temperature-swing adsorption: adsorbents are regenerated by reducing pressure, increasing temperature, or combining these changes.
  • Gas storage: porous materials can increase the amount of methane or hydrogen retained under particular pressure and temperature conditions.
  • Environmental treatment: porous sorbents capture organic vapors and dissolved contaminants, although surface reactions may accompany physical adsorption.
  • Analytical separations: differences in adsorption contribute to retention in chromatography.
  • Catalysis: physisorption can concentrate reactants near a catalyst and precede more strongly bound surface intermediates.

Limitations and interpretation

High surface area alone does not guarantee useful performance. Working capacity—the amount released between adsorption and regeneration conditions—can matter more than maximum uptake. Selectivity, transport rate, regeneration energy, stability, and the presence of competing species are also important.

Water can strongly alter adsorption by occupying polar sites, forming clusters, or blocking pores. Consequently, performance measured with a dry, pure gas may differ markedly from performance in humid mixtures.

Slow diffusion through narrow pore entrances can prevent an experiment from reaching equilibrium and make accessible pore volume appear smaller than it is. At high pressures, measured excess adsorption must also be distinguished from absolute adsorption: converting between them requires an estimate of the volume assigned to the adsorbed phase.

Isotherm shape, apparent surface area, and fitted adsorption energy are therefore model-dependent evidence. Combining adsorption measurements with calorimetry, spectroscopy, and structural characterization can help distinguish pore confinement, heterogeneous surface interactions, and chemical changes.