The Mohs scale is a comparative scale of hardness that ranks materials by their resistance to scratching. Introduced in 1812 by the German mineralogist Friedrich Mohs, it assigns values from 1 to 10 to ten reference minerals, from talc to diamond. A material that scratches a reference mineral but is scratched by the next harder one has a hardness between those reference values. The scale is widely used in geology and mineral identification because it requires little equipment, but it is ordinal rather than linear: equal numerical steps do not represent equal increases in scratch resistance.
Reference minerals
The original reference sequence remains the standard form of the scale.
| Mohs hardness | Reference mineral | Identifying context |
|---|---|---|
| 1 | [[talc | Talc]] |
| 2 | [[gypsum | Gypsum]] |
| 3 | [[calcite | Calcite]] |
| 4 | [[fluorite | Fluorite]] |
| 5 | [[apatite | Apatite]] |
| 6 | [[orthoclase | Orthoclase]] |
| 7 | [[quartz | Quartz]] |
| 8 | [[topaz | Topaz]] |
| 9 | [[corundum | Corundum]] |
| 10 | Diamond | The hardest reference mineral |
These numbers describe the ordering of the reference minerals, not a measured quantity with a physical unit. A hardness of 8 does not mean that a material is twice as hard as one rated 4. Decimal values, such as 6.5, indicate an intermediate position; they do not establish a uniformly spaced numerical scale.
Principle and testing method
A scratch test compares two surfaces by attempting to make a permanent groove in one with a pointed edge of the other. Under suitable conditions, the harder material scratches the softer one. Specimens of approximately equal hardness may scratch one another, and borderline results can depend on the surfaces and testing conditions.
A typical comparison proceeds as follows:
- Select a fresh, representative surface of the unknown material.
- Draw a pointed edge of a reference mineral across it with controlled force.
- Remove loose powder and inspect the surface for a genuine groove.
- Repeat with other references to bracket the unknown material’s hardness.
- Where practical, reverse the comparison by testing whether the unknown scratches the reference.
The distinction between a scratch and a streak is important. A softer material can leave powder on a harder surface without cutting it. Wiping away the residue, followed by inspection with a hand lens or microscope, helps distinguish a deposited mark from a groove.
Common objects provide rough comparisons when reference minerals are unavailable. A fingernail has a hardness of about 2–2.5, while ordinary window glass is commonly about 5–6. Knife blades and steel files vary with alloy and heat treatment, so they are less dependable than a well-characterized reference set.
Scratch testing removes or damages material. This limits its suitability for finished gemstones, polished objects, museum specimens, and thin coatings.
What the scale measures
The Mohs scale measures scratch resistance, not every property commonly described as hardness or strength. It does not directly measure resistance to breaking, bending, crushing, or impact.
In particular, hardness differs from fracture toughness, which describes resistance to crack propagation. Diamond is extremely scratch-resistant but can chip or split along particular crystallographic planes. A softer material may withstand an impact better than a harder, brittle one.
Hardness depends partly on chemical bonding and crystal structure, but it also reflects defects, microstructure, and the mechanism by which a surface deforms or fractures. The contrast between diamond and graphite, both forms of carbon, illustrates how different atomic arrangements can produce very different mechanical properties.
Scratch resistance can also vary with direction within a crystal. This directional dependence is an aspect of crystallography. Kyanite, for example, has markedly different hardness values in different crystallographic directions. Even diamond does not offer identical resistance to abrasion in every direction.
Interpretation and limitations
Unequal intervals
The gaps between successive reference minerals are unequal. The difference between corundum and diamond is much greater than several of the lower steps, but there is no universal conversion factor between their Mohs values and their hardness measured by another method.
Statements that one reference mineral is a fixed number of times harder than another require a specified test method. Scratch, indentation, and abrasion tests probe related but different responses.
Surface and specimen effects
Weathering, alteration, coatings, and contamination can cause a tested surface to behave differently from fresh material. A loose aggregate may crumble rather than develop a clean scratch. In a rock containing several minerals, a scratch test may characterize an individual grain rather than the rock as a whole.
The force applied, the shape of the scratching point, and the support beneath the specimen also affect the result. Very thin coatings may yield responses influenced by their underlying substrate. Consequently, reporting a highly precise Mohs value can imply more certainty than the method supports; a bracketed range is often more informative.
Limited identification power
Many minerals share similar hardness values. Hardness is therefore used alongside properties such as color, streak, luster, density, cleavage, and crystal habit. It can eliminate possibilities, but usually cannot identify a mineral by itself.
Relation to other hardness tests
Engineering and laboratory applications often require more reproducible measurements than a reference-mineral scratch comparison provides.
The Vickers hardness test uses a diamond pyramid indenter and derives hardness from the applied load and the dimensions of the resulting impression. The Knoop hardness test uses an elongated diamond indenter and is useful for small specimens, brittle materials, and thin sections. Rockwell testing instead uses indentation depth under specified loading conditions.
These methods have defined procedures for loading, indenter geometry, and measurement. Their results are not interchangeable with Mohs rankings, and any conversion is approximate and material-dependent. Instrumented scratch tests can quantify scratching under controlled loads, but their outputs likewise require a specified test procedure.
Uses and historical significance
Mohs developed the scale within an approach to mineral classification that emphasized observable physical properties. Its ten reference minerals supplied a practical comparison system that did not require chemical analysis.
The scale remains useful in field geology, mineralogy teaching, and preliminary gemstone examination. It also helps explain why quartz-bearing dust can scratch many softer materials. However, a Mohs value alone does not establish a product’s overall durability: wear also depends on contact conditions, particle shape, repeated loading, and fracture behavior.
Commercial descriptions such as “9H” should not automatically be read as Mohs hardness 9. In coatings and screen-protector advertising, such labels may refer to a pencil-hardness test, which uses a different reference system and procedure.