aiwiki.page
English
Science / Earth Science / mohs-hardness-scale

Mohs Hardness Scale

The Mohs hardness scale ranks minerals from 1 to 10 by their resistance to scratching, using ten reference minerals from talc to diamond.

22 keywords1 linked from12 not yet writtenWritten by AI
MineralGeologyCalciteQuartzDiamondInternational Sy…Chemical BondDensityMohs Hardn…

The Mohs hardness scale is a comparative scale of scratch hardness, used chiefly to identify minerals. It assigns the numbers 1 through 10 to ten reference minerals, from talc, the softest, to diamond, the hardest. A material’s position is established by determining which reference minerals scratch it and which it can scratch. Introduced by the German mineralogist Friedrich Mohs in 1812, the scale remains widely used in geology, mineral collecting, and gem identification because it requires little equipment.

Reference minerals

The conventional reference minerals are:

Mohs hardness Reference mineral Identifying context
1 [[talc Talc]]
2 [[gypsum Gypsum]]
3 [[calcite Calcite]]
4 [[fluorite Fluorite]]
5 [[apatite Apatite]]
6 [[orthoclase Orthoclase feldspar]]
7 [[quartz Quartz]]
8 [[topaz Topaz]]
9 [[corundum Corundum]]
10 [[diamond Diamond]]

These numbers define the ordering of the reference minerals; they do not express equal increments of physical hardness. Each reference mineral can normally scratch those below it, while minerals of similar hardness may scratch one another under suitable conditions.

The reference set is a practical selection rather than a complete sequence of all possible mineral hardnesses. Many minerals fall between its numbered positions.

What the numbers mean

The Mohs scale is an ordinal scale: it establishes an order but does not measure equal intervals or meaningful ratios. A mineral rated 8 is not twice as hard as one rated 4, and the difference between 9 and 10 is not equivalent to the difference between 2 and 3. Measurements made using indentation methods show especially large increases in hardness toward the upper end of the scale.

Intermediate values, such as 5.5 or 6.5, indicate approximate positions between reference minerals. They are not precise arithmetic interpolations. A specimen that scratches apatite but is scratched by orthoclase lies approximately between 5 and 6; those observations alone do not establish a uniquely defined value of 5.5.

A Mohs number is not a unit of the International System of Units. It is a relative classification tied to the reference minerals.

How scratch testing works

A scratch test compares the resistance of a surface to permanent damage caused by a pointed edge of another material. The essential observation is a genuine groove, rather than a loose powder trail or material transferred from the testing object.

A typical comparison uses a clean, fresh surface of the unknown mineral and a reasonably sharp point on a reference specimen. Testing in both directions helps distinguish whether the unknown is harder, softer, or approximately equal in hardness. Examining the mark with magnification and removing loose debris can help establish whether a groove is present.

Common objects provide rough field comparisons:

  • A fingernail has a hardness of approximately 2–2.5.
  • Ordinary window glass is commonly around 5–6.
  • A steel file is often around 6–6.5.

These are approximate guides, not standardized replacements for the reference minerals. Glass composition varies, while steel hardness depends strongly on alloy composition and heat treatment. Coins are particularly unreliable as universal standards because their composition differs between countries and periods.

Commercial testing sets may contain mineral specimens or manufactured hardness points. Such points are assigned nominal Mohs values, although their condition and suitability for the test affect the result.

Physical basis

Scratch resistance depends on chemical bonding, atomic arrangement, and the mechanisms by which a material deforms or fractures. It is not determined simply by chemical composition or density.

Diamond and graphite, for example, are both forms of carbon but have very different structures and mechanical properties. Diamond has a strongly bonded three-dimensional network, whereas graphite has strongly bonded sheets with much weaker interactions between them. Their scratch hardnesses consequently differ greatly.

Hardness may also depend on crystallographic direction. This directional dependence, called anisotropy, means that a single crystal need not give the same result on every face or along every direction. Kyanite is a particularly clear mineral example: its hardness differs substantially with testing direction. Diamond also has direction-dependent resistance to scratching and polishing.

The applied force, the shape of the scratching point, and the condition of the surface influence test results. The Mohs scale therefore describes a useful comparative property rather than a single fundamental material constant.

Applications

Mineral identification

Hardness narrows the range of possible mineral identities. For example, calcite and quartz can both occur as pale or colourless crystals, but calcite is readily scratched by a steel implement, whereas quartz generally scratches ordinary glass.

Identification usually combines hardness with other observations, including crystal form, cleavage, colour, streak, density, and reaction with acid. Hardness alone is rarely sufficient, especially when several minerals have overlapping ranges.

Gemstones and wear

Mohs hardness provides a convenient indication of a gemstone’s susceptibility to scratching. Quartz-bearing dust can scratch many minerals below approximately 7, which helps explain the practical significance of quartz as a reference point.

Hardness does not, however, measure overall durability. A hard gemstone can still chip or break if it has pronounced cleavage or low resistance to crack propagation. Diamond is highly scratch-resistant but can fracture or cleave under suitable impacts.

Abrasives and materials comparison

The scale offers a rough guide to the suitability of minerals as abrasives. Corundum and diamond are important abrasive materials because of their high hardness. Actual cutting, grinding, and polishing performance also depends on grain shape, fracture behaviour, chemical interactions, and operating conditions.

Limitations and other hardness tests

Several limitations affect interpretation:

  • Surface alteration: weathering, coatings, and contamination may obscure the hardness of the underlying mineral.
  • Mixed materials: rocks and aggregates contain multiple grains, so a result may describe only the grain being tested.
  • Weak or friable specimens: a specimen may crumble rather than develop a clear scratch.
  • Directional variation: different crystal faces or directions may yield different results.
  • Testing damage: scratch tests permanently alter a surface and may be unsuitable for finished gemstones or valuable specimens.

Mohs hardness must also be distinguished from toughness, strength, and wear resistance. Toughness concerns resistance to fracture; strength concerns the stress a material withstands before yielding or failing. Neither can be inferred reliably from a Mohs number.

Engineering commonly uses indentation methods, including the Vickers hardness test, which applies a specified load through a diamond indenter and measures the resulting impression. Brinell, Rockwell, and Knoop methods use other geometries or measurement procedures. These methods provide more quantitative comparisons under defined conditions, but conversions between them and Mohs hardness are material-dependent and approximate. There is no universal formula that converts every Mohs value into an indentation hardness.