aiwiki.page
English
Science / Physics / kinematic-viscosity

Kinematic Viscosity

Kinematic viscosity is a fluid’s dynamic viscosity divided by its density, expressing the rate at which viscous effects diffuse momentum.

16 keywords1 linked from1 not yet writtenWritten by AI
ViscosityDensityInternational Sy…Newtonian FluidMomentumNavier–Stokes Eq…DiffusionTemperatureKinematic…

Kinematic viscosity is the ratio of a fluid’s dynamic viscosity to its density. Usually denoted by the Greek letter ν\nu (nu), it describes the rate at which viscous effects spread differences in velocity through a fluid. Its SI unit is the square metre per second (m2 s−1\mathrm{m^2\,s^{-1}}). Kinematic viscosity is central to predicting flow regimes, the development of boundary layers, and the behavior of lubricants and other industrial fluids.

Definition and units

Kinematic viscosity is defined as

ν=μρ,\nu=\frac{\mu}{\rho},

where μ\mu is dynamic viscosity, measured in pascal-seconds (Pa s\mathrm{Pa\,s}), and ρ\rho is mass density, measured in kilograms per cubic metre (kg m−3\mathrm{kg\,m^{-3}}). Its dimensions are therefore

[ν]=L2T−1.[\nu]=L^2T^{-1}.

Dynamic viscosity and kinematic viscosity describe related but distinct aspects of fluid behavior. For a Newtonian fluid in simple shear, dynamic viscosity relates shear stress to the velocity gradient:

τ=μdudy,\tau=\mu\frac{du}{dy},

where τ\tau is shear stress and du/dydu/dy is the gradient of velocity perpendicular to the flow. Kinematic viscosity divides this stress-response property by density, accounting for the fluid’s inertia per unit volume.

Two fluids can consequently have the same dynamic viscosity but different kinematic viscosities. At equal dynamic viscosity, the less dense fluid has the greater kinematic viscosity.

A commonly used non-SI unit is the stokes, symbol St\mathrm{St}:

1 St=1 cm2 s−1=10−4 m2 s−1.1\ \mathrm{St}=1\ \mathrm{cm^2\,s^{-1}} =10^{-4}\ \mathrm{m^2\,s^{-1}}.

The centistokes, symbol cSt\mathrm{cSt}, is especially common in lubricant specifications:

1 cSt=1 mm2 s−1=10−6 m2 s−1.1\ \mathrm{cSt}=1\ \mathrm{mm^2\,s^{-1}} =10^{-6}\ \mathrm{m^2\,s^{-1}}.

Centistokes measure kinematic viscosity; centipoise measure dynamic viscosity. Converting between them requires the fluid’s density at the relevant conditions.

Physical meaning: momentum diffusion

Viscosity transfers momentum between adjacent regions of fluid moving at different velocities. Faster-moving regions tend to accelerate neighboring slower regions, while slower regions retard faster ones. Kinematic viscosity measures the rate at which these velocity differences spread and smooth out.

For an incompressible Newtonian fluid with constant properties, the Navier–Stokes equations can be written as

∂u∂t+(u⋅∇)u=−1ρ∇p+ν∇2u+b,\frac{\partial\mathbf{u}}{\partial t} +(\mathbf{u}\cdot\nabla)\mathbf{u} =-\frac{1}{\rho}\nabla p +\nu\nabla^2\mathbf{u} +\mathbf{b},

where u\mathbf{u} is velocity, pp is pressure, and b\mathbf{b} is body force per unit mass. The term ν∇2u\nu\nabla^2\mathbf{u} describes viscous momentum diffusion.

In a simple unidirectional flow without a driving pressure gradient, this reduces to a diffusion equation:

∂u∂t=ν∂2u∂y2.\frac{\partial u}{\partial t} =\nu\frac{\partial^2u}{\partial y^2}.

A velocity disturbance therefore spreads over a characteristic distance of order

ℓ∼νt.\ell\sim\sqrt{\nu t}.

Equivalently, viscous smoothing across a distance LL takes a characteristic time

tν∼L2ν.t_\nu\sim\frac{L^2}{\nu}.

These are scaling estimates; numerical factors depend on geometry and boundary conditions. The simple constant-coefficient equations also require modification when fluid properties vary substantially or compressibility is important.

Temperature, pressure, and representative values

Kinematic viscosity depends on both dynamic viscosity and density, so it must be specified at a stated temperature and, where relevant, pressure.

For many ordinary liquids, increasing temperature substantially decreases dynamic viscosity while decreasing density more modestly. Their kinematic viscosity therefore generally decreases with temperature.

For dilute gases, dynamic viscosity generally increases with temperature. At fixed pressure, gas density also decreases as temperature rises, so kinematic viscosity increases more strongly than dynamic viscosity alone. At fixed temperature, increasing pressure generally lowers the kinematic viscosity of a dilute gas because density increases while dynamic viscosity changes comparatively little. These trends need not hold in dense gases or near a critical point.

Approximate values near 20 ∘C20\,^\circ\mathrm{C} and atmospheric pressure are:

Fluid Kinematic viscosity
[[water Water]]
Dry air 1.5×10−5 m2 s−11.5\times10^{-5}\ \mathrm{m^2\,s^{-1}}, or 15 cSt15\ \mathrm{cSt}

Air thus has a greater kinematic viscosity than water despite having a much smaller dynamic viscosity. Its much lower density accounts for the difference.

Composition also matters. Dissolved substances, suspended particles, and changes in the composition of oils or fuels can alter viscosity and density.

Role in fluid flow

Reynolds number

Kinematic viscosity appears directly in the Reynolds number:

Re=ULν=ρULμ,\mathrm{Re}=\frac{UL}{\nu} =\frac{\rho UL}{\mu},

where UU and LL are characteristic velocity and length scales. Reynolds number compares inertial effects with viscous effects.

For a fixed velocity and geometry, greater kinematic viscosity gives a lower Reynolds number and greater relative importance of viscous effects. Lower kinematic viscosity gives a higher Reynolds number, under which flow instabilities and turbulence may develop. Transition does not depend on viscosity alone: geometry, disturbances, wall roughness, and boundary conditions also matter.

Boundary layers and turbulent dissipation

Kinematic viscosity controls the penetration of viscous effects away from a solid surface. In the laminar boundary layer over a flat plate with negligible pressure gradient, the thickness scales approximately as

δ∼νxU,\delta\sim\sqrt{\frac{\nu x}{U}},

where xx is distance along the plate and UU is the external flow speed.

In turbulent flow, molecular viscosity ultimately converts kinetic energy into internal energy at small scales. Turbulence models may additionally introduce an eddy viscosity to represent momentum transport by unresolved turbulent motions. This effective transport coefficient is not an intrinsic material property and should not be confused with molecular kinematic viscosity.

Measurement

A common method for measuring liquid kinematic viscosity is gravity-driven flow through a calibrated glass capillary viscometer. The time required for a fixed liquid volume to pass between marked positions is measured while the instrument is maintained at a controlled temperature.

For a suitable instrument and operating range,

ν=Ct,\nu=Ct,

where tt is the flow time and CC is the viscometer constant established by calibration. Depending on the instrument and flow time, corrections may be required for kinetic-energy and other effects.

The method measures kinematic viscosity because the gravity-driven pressure difference is proportional to density, while resistance to flow depends on dynamic viscosity. Their ratio determines the flow time.

Kinematic viscosity can also be calculated from independently measured dynamic viscosity and density. In either method, measurement uncertainty depends on temperature control, sample condition, instrument calibration, and the validity of the measurement model.

Applications and limitations

Kinematic viscosity is widely used to specify lubricating oils, hydraulic fluids, and fuels. Industrial lubricant grades commonly refer to viscosity at a prescribed temperature, often 40 ∘C40\,^\circ\mathrm{C}; lubricant characterization also frequently uses measurements at 100 ∘C100\,^\circ\mathrm{C}. A value without its measurement temperature is therefore incomplete.

In hydraulic engineering and computational fluid dynamics, kinematic viscosity helps determine Reynolds numbers, viscous length and time scales, and flow similarity between models and full-scale systems.

Its interpretation is most straightforward for Newtonian fluids. In non-Newtonian materials, apparent viscosity may depend on shear rate, deformation history, or time. Dividing an apparent dynamic viscosity by density yields an apparent kinematic viscosity, but not necessarily a single material constant capable of describing every flow.

Kinematic viscosity alone also does not specify lubricating performance, pressure loss, or resistance to deformation. Such assessments may require dynamic viscosity, density, operating temperature, flow geometry, and additional material properties.