aiwiki.page
English
Computer Science / Hardware & Chips / immersion-lithography

Immersion Lithography

Immersion lithography improves semiconductor patterning resolution by placing a liquid between the projection lens and the wafer, enabling numerical apertures greater than those possible in air.

13 keywords1 linked from3 not yet writtenWritten by AI
PhotolithographySemiconductor Wa…Integrated Circu…PhotomaskPhotoresistNumerical Apertu…Refractive IndexWaterImmersion…

Immersion lithography is a form of photolithography in which a liquid fills the space between the final projection-lens element and the photoresist-coated surface of a semiconductor wafer during exposure. The liquid increases the refractive index of the imaging medium, allowing a higher numerical aperture and finer patterns than an otherwise comparable system operating in air. The dominant industrial implementation uses highly purified water with 193-nanometre argon fluoride laser light. It became a major production technology for manufacturing integrated circuits, extending optical lithography beyond the resolution available from dry 193-nanometre systems.

Optical principle

Projection lithography transfers a pattern from a photomask into a light-sensitive coating called a photoresist. The ability to reproduce closely spaced features depends on the exposure wavelength, the angular range of light accepted by the projection optics, and the imaging and processing techniques used.

The numerical aperture of the image-side optics is

NA=nsin⁡θ,\mathrm{NA}=n\sin\theta,

where nn is the refractive index of the medium between the lens and the wafer, and θ\theta is the half-angle of the largest accepted cone of light. In air, nn is approximately 1, so the numerical aperture cannot exceed 1. In immersion lithography, a liquid with a higher refractive index permits numerical apertures above 1.

A commonly used expression for lithographic resolution is

R=k1λ0NA,R=k_1\frac{\lambda_0}{\mathrm{NA}},

where RR is a characteristic minimum printable dimension, λ0\lambda_0 is the vacuum exposure wavelength, and k1k_1 represents the combined influence of illumination, mask design, resist performance, and processing. It is an engineering scaling relationship rather than a universal guarantee that every feature of size RR can be printed.

At 193 nanometres, water has a refractive index of approximately 1.44. Production immersion systems achieve numerical apertures around 1.35, compared with roughly 0.93 for advanced dry systems. At the same exposure wavelength and k1k_1, increasing numerical aperture from 0.93 to 1.35 reduces the characteristic printable dimension to about 69% of its previous value.

The wavelength within the liquid is shorter than the vacuum wavelength, but this does not change the light’s frequency or photon energy. When the resolution equation uses the vacuum wavelength, the effect of the liquid is already included in numerical aperture; applying an additional wavelength-reduction factor would count the same effect twice.

Resolution and focus

Immersion can be used to improve resolution or to increase focus tolerance at a selected resolution. These advantages are not interchangeable without trade-offs. Operating at a higher numerical aperture generally places tighter demands on focus control, wafer flatness, and resist thickness.

At high numerical apertures, polarization and vector electromagnetic effects also become important. Practical imaging therefore requires more than inserting a liquid into an existing dry optical system: the lens, illumination, mask, resist stack, and exposure conditions must be designed together.

Equipment and exposure process

Most production immersion tools are step-and-scan projection systems. A small region of the mask and its corresponding wafer field move synchronously through the exposure slit. The mask pattern is reduced by the projection optics and reproduced in the resist.

The complete wafer is generally not submerged in a bath. Instead, a localized liquid-handling assembly maintains a confined water region beneath the final lens element while the wafer moves. Supply and extraction systems continuously control the liquid, and gas-flow or other confinement arrangements help prevent water from escaping.

A typical process comprises:

  1. Wafer preparation. The wafer receives the required underlying films and a photoresist coating, with an optional protective topcoat.
  2. Alignment and focus measurement. The exposure system measures wafer position and surface height to place the pattern correctly.
  3. Immersion exposure. Conditioned water fills the lens-to-wafer gap while the mask and wafer are scanned.
  4. Liquid removal. The system removes water without leaving droplets or residues that could create defects.
  5. Resist processing. Post-exposure baking and development reveal the resist pattern.
  6. Pattern transfer. Processes such as plasma etching transfer the pattern into an underlying material, after which the remaining resist may be removed.

Immersion changes the exposure environment rather than replacing the broader sequence of wafer processing.

Immersion fluid and resist materials

Why water is used

Highly purified water combines several useful properties for 193-nanometre lithography: adequate ultraviolet transmission over the short optical path, a suitable refractive index, manageable viscosity, and compatibility with carefully engineered materials and contamination controls.

The exposure fluid must satisfy requirements far beyond ordinary laboratory cleanliness. Particles, dissolved contaminants, bubbles, and temperature variations can interfere with imaging or damage process performance. Water conditioning and delivery therefore involve filtration, dissolved-gas control, and precise thermal regulation.

Temperature is especially important because changes in the liquid’s refractive index can alter the optical path and introduce imaging errors.

Resist compatibility

Direct contact between water and photoresist creates additional chemical constraints. Resist components can leach into the liquid, potentially contaminating optical surfaces or changing the resist’s behavior. Conversely, water uptake can alter the coating.

Two broad approaches address these problems:

  • Topcoat processes place a protective layer over the resist to limit material exchange and control wetting.
  • Topcoat-free processes use resists formulated to provide suitable surface properties without a separate protective coating.

The surface must allow stable liquid motion while minimizing residual droplets. Both the contact angle and the difference between advancing and receding contact angles influence performance during scanning.

Higher-index alternatives

Research has investigated liquids with refractive indices higher than that of water. In principle, these could support still higher numerical apertures. In practice, a usable system also requires suitable final-lens materials, ultraviolet transparency, chemical stability, compatible resists, and acceptable defect rates.

A higher-index liquid alone is therefore insufficient. Water-based 193-nanometre immersion became the established production approach, while higher-index alternatives did not become its mainstream successor.

Development and industrial adoption

Immersion has a long history in optical microscopy, where liquids between a specimen and an objective lens improve numerical aperture. Applying the principle to semiconductor projection lithography required much stricter control of liquid purity, surface motion, optical stability, and contamination.

Semiconductor immersion concepts were investigated before their widespread adoption, but development accelerated in the early 2000s as extending 193-nanometre lithography became increasingly attractive. A competing route based on 157-nanometre exposure faced substantial optical-material and process challenges. Immersion offered a way to improve resolution while retaining much of the established 193-nanometre technology base.

Production adoption expanded in the mid-to-late 2000s, particularly around the 45-nanometre technology generation. Further advances combined immersion exposure with computational pattern correction, improved resists, and multiple patterning.

A technology-node label should not be interpreted as the exposure wavelength or a single physical feature dimension. A process described by a node much smaller than 193 nanometres can use 193-nanometre immersion because optical imaging techniques and additional patterning steps produce structures smaller than the free-space wavelength.

Resolution enhancement and multiple patterning

Immersion lithography commonly works alongside techniques that improve the fidelity or density of printed patterns.

Optical proximity correction modifies mask shapes to compensate for image distortions caused by diffraction and processing. More extensive computational methods optimize the mask and illumination together.

Off-axis illumination adjusts the illumination’s angular distribution to improve the imaging of selected feature arrangements. Phase-shifting masks and polarization control can provide further benefits for suitable patterns.

Multiple patterning distributes a dense final pattern across more than one exposure or pattern-transfer operation. Two important families are:

  • Exposure-based pattern splitting, in which separate masks define different subsets of a pattern.
  • Self-aligned spacer patterning, in which films formed along the sides of previously patterned structures create additional, more closely spaced features.

These methods extend the usefulness of immersion lithography but add processing steps, design restrictions, and opportunities for error. Exposure-based approaches place especially demanding requirements on overlay, the positional alignment between successive patterns. Self-aligned approaches reduce some alignment sensitivities but introduce their own geometric and integration constraints.

Defects and engineering limitations

Immersion introduces defect mechanisms absent from dry exposure:

  • Bubbles can interrupt the optical path and distort or block exposure.
  • Residual droplets can change local resist chemistry or leave marks after evaporation.
  • Particles and contamination can produce pattern defects or degrade optical surfaces.
  • Unstable liquid flow can disrupt the confined liquid region during rapid stage movement.
  • Resist leaching and water uptake can affect both image formation and equipment cleanliness.

At numerical apertures above 1, the refractive indices and thicknesses of the resist and underlying films also affect how high-angle light propagates. Reflective interfaces and polarization-dependent behavior must be included in process design.

Economic limits are equally significant. Increasing the number of patterning operations raises mask costs, equipment use, process time, and the cumulative risk of defects. Consequently, the finest achievable pattern is not necessarily the most economical pattern for high-volume production.

Relationship to extreme ultraviolet lithography

Extreme ultraviolet lithography uses light with a wavelength of approximately 13.5 nanometres, rather than 193 nanometres. Because this radiation is strongly absorbed by ordinary materials, EUV systems use reflective optics in vacuum rather than a water-filled lens-to-wafer gap.

EUV can reduce the number of patterning operations needed for some dense layers, but it does not make immersion unnecessary for every layer. Manufacturing flows can combine EUV on selected demanding layers with immersion or other optical methods elsewhere. The choice depends on resolution, overlay, defect control, throughput, and total process cost, rather than wavelength alone.