Hooke’s law states that, within a suitable range of deformation, an elastic system’s restoring force is proportional to its displacement from equilibrium. For an ideal spring, it is written , where is displacement and is the spring constant. In materials science, its more general form relates stress to strain through elastic constants. The law is an approximation rather than a universal property of matter: it applies where the mechanical response is approximately linear and reversible.
Spring form
For an ideal spring constrained to move along one axis,
where:
- is the force exerted by the spring;
- is the signed displacement from its unstretched equilibrium position;
- is the spring constant, or stiffness.
The minus sign indicates that the spring force opposes displacement. Stretching the spring produces a force tending to shorten it; compressing it produces a force tending to lengthen it. For slow loading in mechanical equilibrium, the applied external force balances the spring force, so .
In the International System of Units, is measured in newtons per metre, . A larger value means that a greater force is required to produce the same displacement.
For example, a spring with , extended by , exerts a restoring force of magnitude . This calculation is valid only if the extension remains within the spring’s linear operating range.
The spring constant characterizes an entire component, not just its material. It depends on geometry, dimensions, and how the component is loaded. Two springs made from the same material can therefore have very different stiffnesses.
Stress, strain, and material properties
To describe a material independently of a particular specimen’s size, Hooke’s law is expressed in terms of stress and strain.
For a straight, uniform bar under axial tension, the engineering normal stress is
where is the original cross-sectional area. Engineering axial strain is
where is the original length and is the change in length. For small strains under uniaxial loading,
where is Young’s modulus. Stress and Young’s modulus have the same units as pressure: pascals, or . Strain is dimensionless.
Combining these expressions gives
Thus, the axial stiffness of this bar is
A longer bar is less stiff, while a bar with a larger cross-sectional area is stiffer, assuming identical material and loading conditions. This result is specific to axial deformation; bending and torsional stiffness depend on geometry in different ways.
Other elastic constants
Several constants describe different modes of deformation:
- Shear modulus, : relates shear stress to engineering shear strain through .
- Bulk modulus, : relates an increase in hydrostatic pressure to fractional volume reduction, so for small changes.
- Poisson’s ratio, : describes transverse contraction or expansion accompanying axial deformation. Under uniaxial loading, .
For an isotropic, linearly elastic material, only two independent elastic constants are needed. Common relations are
These relations are not generally valid for anisotropic materials, whose properties depend on direction.
Three-dimensional form
A material element can experience normal and shear stresses simultaneously. In small-strain elasticity, the general linear relation is
where and are components of the stress and strain tensors, and is the elasticity tensor. This formulation includes coupling between different deformation directions.
For conventional elastic materials derived from a strain-energy density, the tensor symmetries reduce the maximum number of independent elastic constants to 21. Material symmetry reduces the number further. An isotropic material requires only two.
For isotropic linear elasticity,
where and are the Lamé parameters, is the sum of the normal strains, and is the Kronecker delta.
This expression distinguishes resistance to volume change from resistance to changes of shape. It also shows why the simple relation cannot be applied independently along each axis when stresses act in several directions: transverse coupling must be included.
Energy and oscillation
Deforming an ideal Hookean spring stores potential energy. The external work required to move it quasistatically from to is
The restoring force follows from the negative derivative of this energy:
For a mass attached to an ideal spring, with no damping or external driving, Newton’s laws of motion give
This is the equation of simple harmonic motion, with angular frequency and period
The ideal period is independent of oscillation amplitude because the force is exactly linear. Real systems can show amplitude-dependent periods when nonlinear effects become significant. Damping also removes mechanical energy and changes the motion.
For a linearly elastic continuum, the stored energy per unit volume is
when stress and strain are measured from an unstressed reference state.
Microscopic basis and approximation
Hookean behavior can often be understood as a local approximation near a stable equilibrium. If a system’s potential energy is smooth, it can be expanded about its equilibrium position:
The linear term vanishes at equilibrium, and positive curvature corresponds to local stability. At sufficiently small displacements, the quadratic term dominates, giving a restoring force approximately equal to .
In solids, deformation changes interatomic separations and bond angles, altering the energy associated with chemical bonding and other interactions. The collective response produces macroscopic elastic constants. Linear behavior can also arise from other mechanisms, including changes in molecular configurations in polymers.
This approximation underlies models of lattice vibrations and phonons, as well as the quantum harmonic oscillator. It does not imply that all systems have a useful Hookean range: the range depends on structure, loading conditions, and the required accuracy.
History
The law is named after Robert Hooke, who published it explicitly in 1678 in De Potentia Restitutiva. He had announced it in an anagram in 1676. Its familiar Latin formulation, ut tensio, sic vis, is commonly translated as “as the extension, so the force.”
Hooke’s formulation concerned the proportionality between loading and deformation in elastic bodies. The modern stress–strain formulation, tensor notation, and distinctions among elastic moduli developed later. His work helped establish the quantitative study of deformable bodies alongside the mechanics of idealized particles and rigid bodies.
Applications and measurement
Hooke’s law is used in spring balances, force sensors, mechanical suspensions, vibration analysis, and structural engineering. It supplies a constitutive relation—that is, a rule describing material response—for many calculations in classical mechanics.
In finite element analysis, linear elastic models are widely used when strains are small and permanent deformation is not expected. Elastic moduli also enter predictions of the speeds of small-amplitude waves in solids.
Experimentally, stiffness is obtained from the slope of a force–displacement curve:
A constant slope indicates a linear response over the measured interval. Young’s modulus is similarly obtained from the slope of a uniaxial stress–strain curve in its linear region. Calibration, specimen dimensions, machine compliance, alignment, and measurement uncertainty affect the inferred values. Elastic constants can also vary with temperature and other environmental conditions.
Limits of validity
Linearity and elasticity are distinct properties. A material is elastic if it recovers its deformation after unloading; its stress–strain relation need not be linear. Rubber-like materials, for example, can undergo large reversible deformations that require nonlinear models.
Important departures from Hooke’s law include:
- Exceeding the proportional range. The force–displacement or stress–strain curve ceases to be straight. This can occur before irreversible deformation begins.
- Plastic deformation. Beyond yielding, unloading can leave permanent strain. The proportional limit and the elastic limit therefore need not coincide.
- Time-dependent response. Viscoelastic materials respond differently depending on loading duration and rate, and can exhibit creep, stress relaxation, and hysteresis.
- Large deformation. Changes in geometry can make a component’s overall response nonlinear even when its material strains remain small.
- Instability and damage. Buckling, cracking, and other structural changes can invalidate a simple linear model.
Hooke’s law alone does not predict strength, fracture, fatigue life, or the load at which a structure becomes unstable. Those questions require additional material properties and mechanical models.