Freezing-point depression is the decrease in the equilibrium freezing temperature of a solvent caused by dissolved substances, compared with the pure solvent at the same pressure. In its usual form, the solid that first separates is essentially pure solvent, while the solute remains in the liquid. For sufficiently dilute, nearly ideal solutions, the decrease depends primarily on the number of dissolved particles rather than their chemical identity. It is therefore classified as a colligative property, alongside boiling-point elevation, vapor-pressure lowering, and osmotic pressure.
Physical basis
Freezing is a phase transition between liquid and solid. At the equilibrium freezing temperature, the chemical potential of the solvent is the same in both phases. Dissolving a solute lowers the chemical potential of the solvent in the liquid relative to that of the pure liquid at the same temperature and pressure. If the solute is excluded from the solid, the solid solvent does not experience the same lowering. A lower temperature is consequently required to restore equilibrium between the phases.
This explanation is more general than descriptions in which solute particles simply “block” ice formation. Dissolved substances can affect crystal growth and nucleation, but equilibrium freezing-point depression is fundamentally a consequence of thermodynamics, not merely a mechanical obstruction to crystallization.
The connection with entropy is especially direct for ideal solutions: mixing increases the entropy of the liquid and lowers the solvent’s chemical potential. In real solutions, molecular interactions also influence the effect. The quantity that captures both ideal mixing and deviations from ideal behavior is the solvent’s thermodynamic activity.
Dilute-solution equation
For a dilute solution, the freezing-point depression is commonly written
where:
- is the freezing temperature of the pure solvent;
- is the temperature at which solid solvent first coexists in equilibrium with the solution;
- is the solvent’s cryoscopic constant, or molal freezing-point depression constant;
- is the solute’s molality, measured in moles of solute per kilogram of solvent;
- is the van ’t Hoff factor, accounting for the effective number of dissolved particles produced per formula unit of solute.
With this convention, is positive for a depression. Temperature differences have the same numerical value in kelvins and degrees Celsius.
Molality is used rather than molar concentration because it is based on solvent mass and does not change merely through thermal expansion or contraction.
For water near its ordinary freezing point,
An ideal aqueous solution containing mol of a nondissociating solute per kilogram of water therefore has a predicted depression of
At atmospheric pressure, its initial equilibrium freezing temperature would be approximately .
Electrolytes and particle number
A solute such as glucose remains predominantly as intact molecules in water, so its dilute-solution van ’t Hoff factor approaches 1. An electrolyte can dissociate into several ions. In the limit of ideal, complete dissociation, sodium chloride gives two particles per formula unit and calcium chloride gives three.
These integer values are limiting approximations, not universal constants. At finite concentrations, interactions between ions and possible ion pairing cause departures from ideal behavior. Solutes that associate into larger molecular units can instead produce fewer independent particles than expected from their analytical concentration.
For several independently dissolved solutes in the dilute ideal limit,
Outside that limit, a model based on solvent activity is preferable to simple particle counting.
Thermodynamic formulation
For equilibrium between pure solid solvent and solvent in a liquid solution,
where the asterisk denotes a pure-phase reference state, is the solvent activity relative to pure liquid solvent, and is the gas constant. The pure liquid reference may be a metastable, supercooled liquid at the temperature of interest.
If the molar enthalpy of fusion, , is treated as constant over the temperature interval, integration gives
For a small depression,
In an ideal solution, , the mole fraction of solvent. At high dilution, is approximately the ratio of solute particles to solvent molecules. This yields the molality equation and the expression
where is the solvent’s molar mass in kilograms per mole.
For a real solution, solvent activity can be written as , where is an activity coefficient. Accurate predictions over larger temperature intervals may also require accounting for the difference in heat capacity between solid and liquid.
Freezing a solution
A pure substance at fixed pressure can freeze at a single equilibrium temperature. A solution generally behaves differently.
When nearly pure solvent crystals form, they remove solvent from the liquid while leaving most solute behind. The remaining liquid becomes more concentrated, and its equilibrium freezing temperature falls further. Freezing can therefore proceed over a range of temperatures rather than at one fixed temperature. The dilute-solution formula normally describes the onset of freezing, not the temperature at which the entire sample becomes solid.
The relation between temperature, composition, and stable phases is represented by a phase diagram. Its liquidus boundary identifies the temperature at which a solid phase first appears on equilibrium cooling.
Many solvent–solute systems have a eutectic point, where a liquid of a particular composition coexists with two solid phases. In the sodium chloride–water system, the eutectic occurs at approximately and 23.3% sodium chloride by mass. The solid phases there are ice and the salt hydrate hydrohalite, .
Adding progressively more salt therefore does not produce an unlimited, linear decrease in freezing temperature. Solubility limits, hydrate formation, and changes in the stable solid phases eventually determine the behavior.
Equilibrium depression and supercooling
Freezing-point depression must be distinguished from supercooling. Supercooling occurs when a liquid remains unfrozen below its equilibrium freezing temperature because formation of a stable crystal nucleus is delayed. It is a kinetic, metastable phenomenon and can occur even in a pure liquid.
In a cooling experiment, the temperature may initially fall below the equilibrium freezing point. Once crystallization begins, release of latent heat can raise the sample temperature toward its solid–liquid equilibrium value. The lowest temperature observed before crystallization is therefore not necessarily the freezing point.
Other effects can also lower a measured freezing or melting temperature, including pressure changes and confinement in very small pores. These have mechanisms distinct from ordinary solute-induced freezing-point depression.
Measurement and cryoscopy
Cryoscopy is the use of freezing-point measurements to investigate solutions. Historically, such measurements helped establish the quantitative laws of dilute solutions, particularly through the work of François-Marie Raoult in the nineteenth century.
A classical application is determining the molar mass of a dissolved substance. For a nondissociating solute in the dilute limit,
where is solute mass in grams and is solvent mass in kilograms, giving in grams per mole. Dissociation, association, impurities, and nonideal behavior complicate this interpretation.
Freezing-point osmometers use the same principle to measure the effective concentration of dissolved particles. Their results are related to osmolality and to the thermodynamic basis of osmosis. They do not, by themselves, identify which chemical substances are present.
Accurate measurement requires control of sample composition, pressure, temperature gradients, and supercooling. Thermometer calibration and identification of the relevant solid–liquid equilibrium are particularly important for small depressions.
Applications
De-icing and cooling mixtures
Road salts lower the freezing temperature of water, allowing liquid brine to exist below the freezing point of pure water. Salt must dissolve in liquid water to produce this effect. Practical performance depends on temperature, available moisture, dissolution rate, and the relevant phase diagram—not only on the dilute-solution cryoscopic constant.
Mixtures of ice and salt also provide cooling below . Melting ice absorbs heat, while dissolved salt permits liquid water to coexist with ice at a lower temperature. Such mixtures have long been used in ice-cream making and laboratory cooling baths.
Antifreeze formulations
Glycols and other soluble compounds lower the freezing temperature of water-based heat-transfer fluids. Commercial antifreeze mixtures are often too concentrated for the simple molality equation to be quantitatively reliable; their behavior is described using measured phase diagrams or nonideal-solution models.
Natural waters and food systems
Dissolved salts lower the freezing temperature of seawater. Typical ocean-surface seawater begins freezing near , with the exact value depending on salinity and pressure. As sea ice forms, much of the salt is excluded into the remaining brine.
Sugars, salts, and other dissolved substances similarly influence the amount of ice present in frozen foods at a given temperature. Their effects on freezing behavior interact with crystal growth, viscosity, and the concentration of the unfrozen liquid.
Scope and limitations
The relation is a limiting law. It is most reliable when the solution is dilute, the depression is small, and the solid phase is essentially pure solvent. Substantial departures occur when:
- solvent activity differs appreciably from its ideal-solution value;
- the solute dissociates, associates, or reacts in a concentration-dependent way;
- the solid incorporates solute or forms a compound with it;
- a different solid phase becomes stable;
- the temperature interval is large enough that the enthalpy of fusion cannot be treated as constant.
A suspended insoluble substance does not produce the ordinary molecular colligative effect merely by being present. It may nevertheless alter nucleation, heat transfer, or the apparent freezing behavior. Likewise, biological antifreeze proteins can inhibit ice growth through specific interactions with ice surfaces; those effects are not described solely by dilute-solution particle counting.