Fractional distillation is a form of distillation that separates a liquid mixture into fractions of different composition through repeated contact between rising vapor and descending liquid. Separation depends on differences in volatility—the tendency of a substance to enter the vapor phase under specified conditions. A fractionating column provides successive opportunities for vapor and liquid to exchange material, generally enriching the rising vapor in more volatile components and the descending liquid in less volatile components. The method is widely used in petroleum refining, chemical manufacture, solvent purification, and the separation of liquefied air.
Physical basis
Vapor–liquid equilibrium
When a liquid mixture partially vaporizes, the vapor usually has a different composition from the liquid. For many mixtures, the vapor contains a greater proportion of the more volatile component. Condensing that vapor and vaporizing the resulting liquid again can therefore increase its concentration further.
This behavior is described by vapor–liquid equilibrium. At a specified temperature and pressure, equilibrium relations determine how each component is distributed between the two phases. Fractional distillation exploits these relations repeatedly rather than relying on a single vaporization step.
For an ideal liquid mixture in equilibrium with an approximately ideal vapor, Raoult’s law gives
where and are the mole fractions of component in the liquid and vapor, is total pressure, and is the saturation vapor pressure of the pure component at temperature .
Real liquid mixtures may depart substantially from ideal behavior. At sufficiently low pressures, a common correction is
where is the liquid-phase activity coefficient. At higher pressures, additional corrections for vapor nonideality may be necessary.
Relative volatility
The ease of separating two components is often characterized by their relative volatility:
If , component is more volatile than component . As relative volatility approaches unity, enrichment at each contact becomes smaller, and more stages, greater internal circulation, or a different separation method may be required.
Pure-component boiling points are useful indicators, but boiling-point difference alone does not determine separability. Relative volatility can change with composition and operating pressure, and some mixtures form constant-boiling compositions that limit ordinary distillation.
Fractionating columns
A typical continuous fractionating system contains a column, a reboiler, a condenser, and equipment for collecting products and returning liquid to the column.
- Reboiler: Supplies heat to vaporize part of the liquid near the column bottom.
- Column internals: Trays or packing provide surfaces and flow paths for contact between vapor and liquid.
- Condenser: Removes heat from overhead vapor, causing condensation.
- Reflux system: Returns part of the condensed overhead liquid to the column.
- Product outlets: Withdraw overhead distillate, bottom liquid, and sometimes intermediate side streams.
Vapor generally rises while liquid flows downward. Their contact transfers both material and heat: more volatile components preferentially enter the vapor, while less volatile components preferentially enter the liquid. This is not simply mechanical sorting according to boiling point; both phases usually contain several components.
In many conventional columns, temperature increases from top to bottom. The actual profile depends on composition, pressure, feed condition, and heat flows.
Trays and packing
Tray columns use discrete contacting devices, such as sieve trays, valve trays, or bubble-cap trays. Vapor passes through liquid held on each tray, and liquid generally flows between trays through downcomers.
Packed columns contain randomly arranged packing pieces or structured packing. Liquid spreads over the packing while vapor passes through its open spaces. Packed columns can provide low pressure drop, an important advantage in vacuum service.
Both designs must balance contact efficiency, throughput, pressure drop, and operational reliability. Excessive flow can cause flooding, in which liquid cannot drain effectively. In tray columns, inadequate vapor flow can cause liquid to leak through tray openings, a condition called weeping. Poor liquid distribution can reduce the effectiveness of packing.
Equilibrium stages
Column performance is commonly expressed using the concept of a theoretical plate, or equilibrium stage: an idealized contact from which the outgoing vapor and liquid are in equilibrium.
An actual tray does not necessarily achieve one theoretical stage. Packed-column performance is often described by the height equivalent to a theoretical plate, or HETP. These measures connect equilibrium calculations to physical column dimensions, but their values depend on the mixture, flow rates, and equipment design.
Reflux and operating modes
Reflux is the condensed liquid returned to the top of the column. It supplies the descending liquid that contacts the rising vapor. For a conventional column with a total condenser, the reflux ratio is
where is the molar reflux flow and is the molar distillate product flow.
For a specified separation and otherwise comparable conditions, increasing reflux generally reduces the number of theoretical stages required, but increases reboiler and condenser duties. At total reflux, all overhead condensate is returned and no overhead product is withdrawn; this condition gives the minimum number of stages for a specified separation in conventional design calculations. At the limiting minimum reflux ratio, an idealized calculation requires infinitely many stages. Practical operation lies between these limits.
Batch distillation
In batch operation, a finite charge is placed in a vessel and distilled over time. As more volatile material is removed, the liquid remaining in the vessel changes composition. Successive portions of distillate may therefore be collected as different fractions.
Laboratory fractional distillation commonly uses a heated flask, a glass fractionating column, a distillation head, a condenser, and receiving vessels. A Vigreux column uses inward-pointing glass indentations to increase contact area; other laboratory columns use packing.
Unlike a continuously fed column at steady state, a batch column generally changes composition and temperature throughout the run.
Continuous distillation
In continuous operation, feed enters while products are withdrawn continuously. A conventional column often has a rectifying section above the feed, which enriches the vapor in more volatile components, and a stripping section below it, which removes more volatile components from the descending liquid.
Feed composition and thermal condition affect internal flows and the appropriate feed location. Design uses material balances, energy balances, equilibrium relations, and estimates of mass-transfer performance.
For a simple steady-state column without side streams,
where , , and are molar feed, distillate, and bottoms flow rates, and , , and are the corresponding mole fractions of component . These equations express conservation of mass but must be combined with equilibrium and energy calculations to determine the separation.
Applications
Petroleum refining
Crude oil contains many hydrocarbons and other compounds. Atmospheric fractional distillation separates it into streams characterized chiefly by boiling ranges, including naphtha, kerosene-range material, gas oils, and atmospheric residue. These are mixtures rather than pure substances, and they normally undergo further treatment or conversion.
Heavy residue can be fractionated under reduced pressure. Lowering pressure permits vaporization at lower temperatures, limiting thermal decomposition that would otherwise occur. Refinery columns often include side draws and auxiliary stripping equipment rather than functioning as simple two-product columns.
Air separation
Large air-separation plants use low-temperature distillation to separate liquefied air, principally into nitrogen and oxygen. Argon can also be recovered. Before cryogenic processing, contaminants such as water and carbon dioxide are removed to prevent freezing and blockage.
Chemical and solvent processing
Fractional distillation is used to separate chemical feedstocks and reaction products, recover solvents, and concentrate ethanol. It is especially useful when components have adequate relative volatility and remain stable at the operating temperature.
Limitations and specialized methods
Azeotropes
An azeotrope is a mixture whose equilibrium vapor and liquid have the same composition at a specified pressure. Ordinary fractional distillation cannot pass through an azeotropic composition at that pressure.
Ethanol and water form a minimum-boiling azeotrope at approximately 95.6% ethanol by mass at atmospheric pressure. Consequently, ordinary fractionation of a dilute ethanol–water mixture cannot produce anhydrous ethanol.
Specialized methods can alter or supplement the separation:
- Pressure-swing distillation exploits changes in azeotropic composition with pressure, where those changes are sufficiently large.
- Extractive distillation adds a relatively nonvolatile solvent that changes relative volatility.
- Azeotropic distillation introduces an additional component to alter the phase-equilibrium behavior.
- Adsorption or membrane separation can remove residual water or other impurities after distillation.
Adding stages alone cannot overcome a fixed-pressure azeotropic barrier.
Energy and thermal constraints
Distillation repeatedly vaporizes and condenses material, requiring substantial energy transfer associated with latent heat. Mixtures with close relative volatilities can demand tall columns and high internal flow rates. Heat integration, vapor recompression, and thermally coupled column arrangements can reduce external energy demand, although they introduce additional design and control requirements.
Heat-sensitive materials may decompose or react during processing. Vacuum operation lowers boiling temperatures, but the accompanying lower vapor density can require larger equipment. Where volatility differences are inadequate, alternatives such as chromatography, extraction, crystallization, or membrane processes may be more suitable.
Historical development
Distillation predates modern chemical engineering, but increasingly effective fractionation developed with improvements in contacting equipment, reflux control, and industrial heat exchange. Nineteenth-century continuous stills expanded the large-scale production of spirits. Petroleum refining and, later, cryogenic air separation extended the industrial importance of fractionating columns.
The subsequent development of equilibrium-stage calculations, thermodynamic models, and numerical simulation made it possible to design increasingly complex multicomponent separations. Modern column design combines these models with experimental equilibrium data and practical knowledge of hydraulics and mass transfer.