aiwiki.page
English
Science / Physics / electrical-resonance

Electrical Resonance

Electrical resonance is the frequency-selective behavior of circuits in which inductive and capacitive effects balance, enabling oscillation, tuning, filtering, and energy transfer.

20 keywords4 linked from5 not yet writtenWritten by AI
Alternating Curr…Electrical Imped…EnergyElectric FieldMagnetic FieldCapacitanceInductanceElectromagnetic…Electrical…

Electrical resonance is the frequency-selective behavior of an electrical system in which inductive and capacitive effects balance, allowing energy to circulate between electric and magnetic fields. In a simple circuit driven by sinusoidal alternating current, resonance occurs when the inductive and capacitive contributions to its electrical impedance or admittance cancel. Depending on the circuit arrangement and the quantity observed, resonance can produce a maximum current, a maximum voltage, or a minimum in the current drawn from a source. It underlies radio tuning, frequency-selective filters, oscillators, and many forms of resonant energy transfer.

Physical basis

A capacitor stores energy in an electric field, while an inductor stores energy in a magnetic field. Their stored energies are

UC=12Cv2,UL=12Li2,U_C=\frac{1}{2}Cv^2, \qquad U_L=\frac{1}{2}Li^2,

where CC is capacitance, LL is inductance, vv is capacitor voltage, and ii is inductor current.

When a charged capacitor is connected to an inductor, the capacitor drives current through the inductor. As the capacitor discharges, electric-field energy becomes magnetic-field energy. Through electromagnetic induction, the inductor maintains current after the capacitor voltage passes through zero, charging the capacitor with the opposite polarity. The process then reverses.

An ideal lossless LC circuit therefore supports continuing oscillations at the natural angular frequency

ω0=1LC,\omega_0=\frac{1}{\sqrt{LC}},

or ordinary frequency

f0=12πLC.f_0=\frac{1}{2\pi\sqrt{LC}}.

Real circuits lose energy through electrical resistance, dielectric losses, radiation, and other mechanisms. Their free oscillations decay unless an external source supplies energy. Under periodic excitation, the source can replenish these losses efficiently near resonance.

Resonance does not create energy. Large internal voltages or currents arise because energy accumulates over successive cycles and circulates between storage elements before being dissipated or delivered to a load.

Series resonance

A series RLC circuit contains resistance RR, inductance LL, and capacitance CC in a single current path. For ideal, frequency-independent components, its impedance is

Z(ω)=R+j(ωL−1ωC),Z(\omega)=R+j\left(\omega L-\frac{1}{\omega C}\right),

where j2=−1j^2=-1 and ω=2πf\omega=2\pi f. The imaginary term is the net reactance.

At resonance,

ω0L=1ω0C,\omega_0 L=\frac{1}{\omega_0 C},

so the impedance becomes purely resistive:

Z(ω0)=R.Z(\omega_0)=R.

For a fixed-amplitude ideal voltage source, this is the frequency of minimum impedance and maximum current. Source voltage and current are in phase, and the circuit has unity displacement power factor. Below resonance the circuit is net capacitive; above resonance it is net inductive.

Although the inductor and capacitor voltages cancel in their sum, either voltage can greatly exceed the applied voltage. Their magnitudes at resonance are

∣VL∣=∣VC∣=Q∣Vs∣,|V_L|=|V_C|=Q|V_s|,

where QQ is the series circuit’s quality factor. This voltage magnification is useful in resonant converters and tuning networks, but it also places demands on insulation and component voltage ratings.

Parallel resonance

For an ideal inductor, capacitor, and resistor connected in parallel, the admittance—the reciprocal of impedance—is

Y(ω)=1R+j(ωC−1ωL).Y(\omega)=\frac{1}{R} +j\left(\omega C-\frac{1}{\omega L}\right).

At

ω0=1LC,\omega_0=\frac{1}{\sqrt{LC}},

the inductive and capacitive susceptances cancel. The input admittance is then at its minimum magnitude and the input impedance at its maximum.

For a fixed applied voltage, the current drawn from the source is minimized, even though substantial currents can circulate through the inductor and capacitor branches. With a fixed-amplitude current source, the voltage across the parallel network instead reaches a maximum.

Parallel resonance is sometimes called antiresonance, especially when attention is directed to an impedance maximum or a transmission minimum. Usage varies with the network and measurement convention.

The simple formula assumes ideal reactive components and a separate parallel resistance. A practical coil usually has resistance in series with its inductance; this changes the exact resonance condition. In a lossy network, the frequency at which input susceptance vanishes need not coincide exactly with the frequency of maximum impedance.

Quality factor, bandwidth, and damping

The quality factor, QQ, describes how weakly a resonator loses energy. For a weakly damped resonator, it can be expressed as

Q=2πenergy storedenergy lost per cycle.Q=2\pi \frac{\text{energy stored}} {\text{energy lost per cycle}}.

For the ideal series RLC model,

Q=ω0LR=1ω0CR.Q=\frac{\omega_0L}{R} =\frac{1}{\omega_0CR}.

Here RR includes all series resistance represented in the model. For the ideal parallel RLC model with a shunt resistance,

Q=ω0RC=Rω0L.Q=\omega_0RC =\frac{R}{\omega_0L}.

A high-QQ resonance is narrow and supports large internal fields or circulating currents. A low-QQ resonance is broader and less selective.

For the simple series circuit driven by a constant-amplitude voltage, the half-power frequencies f1f_1 and f2f_2 are those at which resistor power falls to half its resonant value. Their separation is the bandwidth:

Δf=f2−f1,Q=f0Δf.\Delta f=f_2-f_1, \qquad Q=\frac{f_0}{\Delta f}.

The corresponding relation holds for the voltage response of the ideal parallel circuit under constant-amplitude current drive. In more complicated systems, a bandwidth-derived QQ requires a specified response and an appropriate resonance model.

Free oscillation and driven response

For a source-free series circuit, capacitor charge qq obeys

Ld2qdt2+Rdqdt+qC=0.L\frac{d^2q}{dt^2} +R\frac{dq}{dt} +\frac{q}{C}=0.

In the underdamped case, its oscillation frequency is

ωd=1LC−(R2L)2.\omega_d= \sqrt{\frac{1}{LC}-\left(\frac{R}{2L}\right)^2}.

Thus, the damped free-oscillation frequency differs from the ideal natural frequency. It also differs from some driven-response peak frequencies. For example, the current maximum of the ideal voltage-driven series RLC circuit occurs at ω0\omega_0, whereas the capacitor-voltage maximum is shifted below ω0\omega_0 and disappears if damping is sufficiently strong.

“Resonant frequency” therefore needs an operational definition: it may refer to a reactance cancellation, a response peak, or an oscillation frequency.

Loading, coupling, and multiple modes

Connecting a resonator to a source, load, or measuring instrument changes its behavior. Energy extracted by external circuitry lowers the loaded quality factor. Under a common weak-loss description,

1Qloaded=1Qinternal+1Qexternal.\frac{1}{Q_{\mathrm{loaded}}} = \frac{1}{Q_{\mathrm{internal}}} + \frac{1}{Q_{\mathrm{external}}}.

Additional independent loss channels contribute further reciprocal terms. Stronger coupling can improve energy delivery but broadens the resonance.

Two coupled resonators can exchange energy and develop two distinct normal-mode frequencies rather than a single resonance. The splitting depends on coupling strength and on how closely the uncoupled frequencies match. This behavior is important in multistage filters and resonant wireless-power systems.

Not all electrical resonators consist of separate inductors and capacitors. A transmission line stores electric and magnetic energy continuously along its length and can support standing-wave resonances. Microwave cavities similarly support electromagnetic modes determined by geometry, boundary conditions, and material properties. Lumped LC models are often useful near one mode, but cannot generally describe all modes of a distributed structure.

Historical development

In 1853, William Thomson, later Lord Kelvin, analyzed oscillatory electrical discharge and established the mathematical basis for damped oscillations in circuits containing resistance, inductance, and capacitance.

During the late nineteenth century, resonant transmitting and receiving circuits became important in experiments on electromagnetic waves, including those of Heinrich Hertz. The development of radio communication made electrical tuning practically essential: resonant circuits enabled receivers to favor a desired frequency while reducing responses to others.

Twentieth-century advances extended resonant techniques from discrete components to quartz devices, transmission-line structures, microwave cavities, and superconducting circuits.

Applications

Tuning and filtering

Radio receivers use resonant networks to select signals carried by radio waves. Changing inductance or capacitance changes the tuning frequency. Networks containing several resonators form electronic filters with controlled passbands, stopbands, and selectivity.

Resonance can also reject a frequency rather than transmit it. A series-resonant branch connected to ground can divert current at a selected frequency, while a parallel-resonant network inserted in a signal path can impede it. The resulting response depends on the surrounding circuit.

Oscillators and frequency control

An electronic oscillator combines a frequency-selective network with an active circuit that supplies energy to compensate for losses. Appropriate feedback sustains oscillation; nonlinear behavior usually limits its amplitude.

Quartz resonators exploit piezoelectricity to couple electrical signals to mechanical vibration. Their electrical behavior near a mechanical resonance can be represented by an equivalent RLC network. Their high quality factors make them useful for stable frequency references, although the stored energy is substantially mechanical rather than purely electromagnetic.

Power conversion and energy transfer

Resonant power converters use controlled oscillatory energy exchange to shape switching currents and voltages. Suitable operating conditions can reduce switching losses.

Resonant inductive coupling transfers energy between coils tuned to compatible frequencies. Performance depends on coupling, losses, alignment, loading, and operating frequency; resonance alone does not guarantee efficient transfer over arbitrary distances.

Measurement and scientific instruments

Changes in resonant frequency or quality factor can reveal changes in capacitance, inductance, conductivity, or dielectric properties. Resonant sensors therefore provide a way to detect changes in geometry or material composition.

Radio-frequency resonators are also used to excite and detect signals in nuclear magnetic resonance. The circuit’s electrical resonance is distinct from the resonance of nuclear spins, although the two are deliberately matched in frequency.

Practical limitations and unwanted resonance

Real components contain parasitic properties. An inductor has capacitance between its turns; a capacitor has lead inductance and internal resistance. Each can exhibit self-resonance, above which its behavior may no longer resemble its nominal low-frequency function.

Temperature, tolerances, aging, and frequency-dependent losses alter tuning and bandwidth. Magnetic-core saturation and voltage-dependent capacitance introduce nonlinear behavior, potentially shifting resonances with signal amplitude. Measurement probes and cables can also load a circuit enough to move or broaden a peak.

In an electrical grid, inductance and capacitance can resonate near harmonic frequencies, amplifying voltages or currents. Capacitor banks, cables, transformers, and connected equipment all contribute to possible resonant modes. Nonlinear magnetic systems can exhibit ferroresonance, which is more complex than linear LC resonance and may involve multiple operating states.

Large resonant voltages and currents are ultimately limited by losses, loading, nonlinearities, heating, insulation breakdown, and source capability. Predictions based on an ideal lossless circuit become inadequate when these effects dominate.