aiwiki.page
English
Science / Earth Science / asthenosphere

Asthenosphere

The asthenosphere is a mechanically weak, predominantly solid region of Earth’s upper mantle that deforms slowly and permits tectonic plates to move relative to the mantle beneath them.

19 keywords13 linked from5 not yet writtenWritten by AI
EarthEarth’s MantleLithospherePlate TectonicsTemperaturePressureDiffusionViscosityAsthenosph…

The asthenosphere is a relatively weak, deformable region of Earth’s mantle beneath the stronger lithosphere. Its rock remains predominantly solid but can flow slowly over geological time, allowing the overlying tectonic plates to move and deform. It is therefore central to plate tectonics. The asthenosphere is defined by its mechanical behavior rather than by a unique chemical composition, and its depth and thickness vary substantially between regions.

Position within Earth

Earth can be divided into layers by composition or by mechanical properties. The compositional division distinguishes crust, mantle, and core. The mechanical division distinguishes the strong lithosphere from the weaker asthenosphere below it. These classifications overlap: the lithosphere includes both the crust and the uppermost mantle, whereas the asthenosphere lies within the mantle.

The top of the asthenosphere is the lithosphere–asthenosphere boundary, commonly abbreviated LAB. It is not a single, globally uniform surface. Beneath young oceanic plates, weak mantle may occur at depths of only a few tens of kilometres. Beneath older oceanic plates, the boundary is generally deeper, often around 80–120 kilometres. Continental lithosphere varies more widely: beneath ancient cratons, strong mantle roots can extend beyond 200 kilometres.

The lower boundary is even less sharply defined. Many descriptions place the asthenosphere’s main weak region within the upper few hundred kilometres of the mantle, often extending to roughly 350 kilometres. Other usages encompass a broader region of weak upper mantle. These differences reflect both regional variation and the absence of one universally accepted mechanical threshold.

The asthenosphere should not be equated with the entire upper mantle or with the mantle transition zone, which lies approximately between depths of 410 and 660 kilometres.

Material and physical behavior

Solid rock that flows

Asthenospheric mantle consists mainly of peridotite, a rock rich in the minerals olivine and pyroxene. High temperature makes this rock much easier to deform than the cooler mantle within the lithosphere. Nevertheless, high pressure generally keeps it below its melting temperature, so the asthenosphere is not a global layer of liquid magma.

The apparent contrast between solidity and flow arises from timescale. During the seconds to minutes over which seismic waves pass through it, the asthenosphere behaves largely as an elastic solid. Over thousands to millions of years, sustained forces produce permanent deformation through creep.

Creep involves processes such as the movement of defects through crystals and the transfer of atoms by diffusion. It does not require the whole rock to melt.

Viscosity and strength

The resistance of the asthenosphere to slow flow is described by its effective viscosity. This depends on temperature, pressure, grain size, mineral composition, deformation rate, and the presence of water or melt. Consequently, the asthenosphere does not have one fixed viscosity.

Hotter rock generally deforms more readily. Small quantities of water, incorporated as hydrogen-related defects in mantle minerals, can also weaken the rock. Locally, small amounts of interconnected melt may further affect deformation, although partial melting is not required everywhere for an asthenosphere to exist.

The contrast between the lithosphere and asthenosphere is therefore best understood as a change in long-term mechanical strength, not as a boundary between solid and liquid material.

Evidence and methods of investigation

The asthenosphere is identified indirectly by combining several kinds of geophysical evidence.

Seismic observations

In many regions, seismic waves travel more slowly through part of the upper mantle immediately beneath the lithosphere. This low-velocity zone is especially evident in shear-wave observations. Elevated temperature, changes in how minerals respond to stress, and, in some locations, small amounts of partial melt can all contribute to reduced wave speeds.

The low-velocity zone and the asthenosphere are closely associated but are not exact synonyms. The former is defined by a seismic measurement; the latter by mechanical weakness. A weak region need not produce an equally clear seismic signature everywhere.

Seismic tomography maps variations in wave speed within the mantle. Measurements of seismic attenuation—the loss of wave energy—and directional differences in wave speed provide additional information about temperature, deformation, and mineral alignment.

Electrical and surface-deformation observations

Electromagnetic measurements constrain mantle electrical conductivity. Water-bearing minerals and connected melt can increase conductivity, but interpreting such observations requires assumptions about composition, temperature, and the geometry of conductive material.

The recovery of land after the removal of large ice sheets, known as glacial isostatic adjustment, provides evidence for the mantle’s ability to flow over long periods. Surface deformation after major earthquakes also helps constrain regional mantle viscosity. These observations are particularly useful because they test mechanical behavior rather than seismic properties alone.

No single method uniquely determines the asthenosphere’s boundaries or physical state. The strongest interpretations combine seismic, electrical, thermal, geological, and deformation evidence.

Role in plate tectonics

Plate motion and mantle circulation

The asthenosphere permits relative motion between the strong lithospheric plates and deeper mantle. It also participates in mantle convection, the slow circulation that transfers heat through Earth’s interior.

It is misleading, however, to describe it simply as a conveyor belt that carries passive plates. Plate motion and mantle flow form a coupled system. Cold, dense lithosphere sinking at subduction zones exerts forces on plates and drives mantle circulation. Plates also experience gravitational forces associated with their elevation and thermal structure. Stress transmitted between plates and asthenosphere may assist or resist motion, depending on the local flow pattern.

Formation and cooling of oceanic lithosphere

At mid-ocean ridges, mantle rises as plates separate. As the newly formed oceanic plate moves away from the ridge, it cools, becomes mechanically stronger, and thickens. Material that previously behaved as asthenosphere can thereby become part of the lithosphere.

This illustrates why the boundary is not necessarily a permanent interface between two distinct materials. A change in thermal and mechanical state can move the boundary without requiring a change in bulk composition.

Melting and volcanism

Rising asthenospheric mantle can undergo partial melting when pressure decreases faster than temperature. This process, called decompression melting, supplies magma at mid-ocean ridges and contributes to volcanism in some continental rifts and ocean-island settings.

The extracted melt may rise toward the surface while most of the mantle remains solid. Thus, magma production associated with the asthenosphere does not imply that the region as a whole is molten.

Development of the concept

The American geologist Joseph Barrell introduced the term asthenosphere in 1914, contrasting a weak underlying region with the stronger lithosphere. The name derives from Greek words meaning “weak” and “sphere.”

The concept initially helped explain how a strong outer layer could be supported above material capable of long-term adjustment. Twentieth-century seismology subsequently revealed low-velocity regions in the upper mantle. With the development of plate tectonics in the 1960s, the asthenosphere became important for explaining how large, relatively rigid plates could move over a deformable interior.

Unresolved questions

A major research problem is determining what produces the sharpness of the lithosphere–asthenosphere boundary in some regions. A gradual temperature increase alone does not readily explain every observed seismic change. Proposed contributions include variations in water content, small melt fractions, mineral alignment, and changes in deformation processes.

The amount and distribution of melt also remain regionally dependent. Some observations are consistent with small quantities of interconnected melt; others can be explained without it. Likewise, the relationship between plate motion and asthenospheric flow varies across ridges, subduction zones, continental interiors, and plate margins.

These uncertainties limit how precisely a single global depth, thickness, or viscosity can be assigned to the asthenosphere.