{
  "id": "vapor-liquid-equilibrium",
  "title": "Vapor–Liquid Equilibrium",
  "lang": "en",
  "source_lang": "en",
  "summary": "Vapor–liquid equilibrium describes the conditions under which liquid and vapor phases coexist without net transfer of matter between them.",
  "category": "science",
  "subcategory": "chemistry",
  "type": "concept",
  "aliases": [
    "Vapour–liquid equilibrium",
    "liquid–vapor equilibrium",
    "VLE"
  ],
  "generated_at": "2026-11-05",
  "model": "pro/gpt-6.1-sol",
  "url": "https://aiwiki.page/en/vapor-liquid-equilibrium/",
  "translations": {
    "zh-Hans": {
      "url": "https://aiwiki.page/zh/vapor-liquid-equilibrium/",
      "json": "https://aiwiki.page/zh/vapor-liquid-equilibrium.json"
    }
  },
  "sections": [
    {
      "heading": "",
      "text": "Vapor–liquid equilibrium (VLE) is the state in which a liquid phase and a vapor phase coexist with no net transfer of any chemical component between them. Molecules continue to cross the interface in both directions, but the opposing transfers balance. The equilibrium state determines the pressure above a liquid, the temperature at which boiling or condensation begins, and—when several substances are present—the compositions of the coexisting phases.\n\nVLE is a central subject of thermodynamics and a foundation of distillation, refrigeration, natural-gas processing, and solvent recovery. Its practical importance arises largely from the fact that a mixture’s vapor usually has a different composition from its liquid. This difference makes separation possible, but molecular interactions, high pressure, and critical behavior can make the relationship highly nonideal. Describing VLE therefore requires both general equilibrium principles and substance-specific experimental data or molecular models."
    },
    {
      "heading": "Thermodynamic conditions for coexistence",
      "text": "Vapor–liquid equilibrium is a particular form of thermodynamic equilibrium. For two macroscopic phases separated by a planar interface, equilibrium requires equal temperature, equal pressure, and equal chemical potential for every component that can pass between the phases. For a mixture containing \\(C\\) components, the material-equilibrium conditions are\n\n\\[\\mu_i^{L}(T,P,\\mathbf{x}) = \\mu_i^{V}(T,P,\\mathbf{y}), \\qquad i=1,\\ldots,C,\\]\n\nwhere superscripts \\(L\\) and \\(V\\) denote liquid and vapor, and \\(\\mathbf{x}\\) and \\(\\mathbf{y}\\) are their respective mole-fraction vectors. Equal temperature prevents net heat transfer; mechanical equilibrium prevents bulk motion driven by an unbalanced pressure difference; equal chemical potentials prevent net interphase transfer of individual components. Curved interfaces require a pressure difference associated with surface tension, so the equal-pressure statement is an approximation for sufficiently large phases.\n\nAt fixed temperature, pressure, and overall composition, the stable equilibrium state minimizes the total Gibbs free energy. Equality of chemical potentials is necessary for coexistence, but it does not by itself guarantee global stability: a mathematical solution can describe metastable or unstable phases. Stability testing is therefore important when calculating mixtures capable of splitting into more than two phases.\n\nFor practical calculations, chemical potential is commonly expressed through fugacity, a pressure-like measure of a component’s escaping tendency. Using a consistent reference state,\n\n\\[\\mu_i=\\mu_i^\\circ+RT\\ln\\left(\\frac{f_i}{f_i^\\circ}\\right),\\]\n\nwhere \\(R\\) is the gas constant. The equilibrium conditions then become \\(f_i^L=f_i^V\\). For an ideal-gas mixture, component fugacity equals its partial pressure, \\(y_iP\\); in a real vapor, it is written \\(y_i\\phi_iP\\), where \\(\\phi_i\\) is a fugacity coefficient.\n\nThe Gibbs phase rule specifies the number of independent intensive variables. For a nonreacting system,\n\n\\[F=C-\\Pi+2,\\]\n\nwhere \\(\\Pi\\) is the number of phases. A pure substance with liquid and vapor present has one degree of freedom: fixing its temperature fixes its saturation pressure. A binary two-phase mixture has two degrees of freedom; specifying temperature and pressure generally fixes both phase compositions. The amounts of liquid and vapor are not counted among these intensive degrees of freedom and require an additional overall material balance."
    },
    {
      "heading": "Pure substances and the saturation curve",
      "text": "For a pure substance, liquid and vapor coexist along a curve in pressure–temperature space. The pressure on this curve is the saturation vapor pressure, \\(P^{\\mathrm{sat}}(T)\\). Below the critical point, a liquid exposed to a vapor containing only that substance can evaporate or condense until the saturation condition is reached, provided sufficient material and volume are available. In a sealed vessel containing both phases at equilibrium, pressure is determined by temperature rather than independently by the relative amounts of liquid and vapor.\n\nThe slope of the coexistence curve follows the Clapeyron equation:\n\n\\[\\frac{dP^{\\mathrm{sat}}}{dT} = \\frac{\\Delta h_{\\mathrm{vap}}} {T\\left(v^{V}-v^{L}\\right)},\\]\n\nwhere \\(\\Delta h_{\\mathrm{vap}}\\) is the molar enthalpy of vaporization and \\(v^{V}\\) and \\(v^{L}\\) are molar volumes. Vaporization normally increases both enthalpy and volume, so saturation pressure increases with temperature. This relationship connects VLE directly to latent heat and explains why lowering external pressure lowers the boiling temperature.\n\nWhen vapor behaves approximately as an ideal gas and its volume greatly exceeds the liquid volume, the equation reduces to the Clausius–Clapeyron approximation:\n\n\\[\\frac{d\\ln P^{\\mathrm{sat}}}{dT} \\approx \\frac{\\Delta h_{\\mathrm{vap}}}{RT^2}.\\]\n\nIf the enthalpy of vaporization is treated as constant over a limited interval,\n\n\\[\\ln\\left(\\frac{P_2^{\\mathrm{sat}}}{P_1^{\\mathrm{sat}}}\\right) \\approx -\\frac{\\Delta h_{\\mathrm{vap}}}{R} \\left(\\frac{1}{T_2}-\\frac{1}{T_1}\\right).\\]\n\nThis is useful for interpolation and physical interpretation, but broad-range property calculations require the temperature dependence of latent heat and vapor nonideality to be represented more accurately.\n\nFor water, the normal boiling temperature is approximately \\(100\\,^\\circ\\mathrm{C}\\) at \\(101.325\\ \\mathrm{kPa}\\). Its critical temperature is about \\(647.096\\ \\mathrm{K}\\), and its critical pressure is approximately \\(22.064\\ \\mathrm{MPa}\\). At the critical point, liquid and vapor densities become equal and the distinction between the phases disappears. Below the triple-point temperature, the stable condensed phase is ice rather than liquid water, so equilibrium with vapor belongs to the sublimation curve.\n\nBoiling and evaporation are related but not identical. Surface evaporation can occur well below the boiling temperature, especially into unsaturated air. Boiling involves vapor-bubble formation within the liquid and requires the bubble pressure to balance surrounding pressure, including hydrostatic and interfacial contributions. Superheating and delayed bubble formation are kinetic effects; they do not redefine the equilibrium saturation curve."
    },
    {
      "heading": "Ideal mixtures and dilute-solution limits",
      "text": "The simplest mixture model combines an ideal liquid solution with an ideal vapor. Its central relation is Raoult’s law, associated with François-Marie Raoult’s late nineteenth-century studies of solution vapor pressures:\n\n\\[p_i=x_iP_i^{\\mathrm{sat}}(T).\\]\n\nHere \\(p_i\\) is the vapor partial pressure of component \\(i\\), and \\(x_i\\) is its liquid mole fraction. Summing the partial pressures gives the total equilibrium pressure,\n\n\\[P=\\sum_i x_iP_i^{\\mathrm{sat}}, \\qquad y_i=\\frac{x_iP_i^{\\mathrm{sat}}}{P}.\\]\n\nThe component with the higher pure-component saturation pressure is enriched in the vapor. Ideal-solution behavior is most plausible when the components have similar molecular sizes and intermolecular interactions; benzene–toluene mixtures are a familiar approximate example.\n\nFor a binary mixture at fixed temperature, the ideal bubble-pressure relation is linear in liquid composition. The corresponding dew-pressure relation is not linear in vapor composition:\n\n\\[\\frac{1}{P}=\\sum_i\\frac{y_i}{P_i^{\\mathrm{sat}}}.\\]\n\nThe distinction matters because a liquid just beginning to boil and a vapor just beginning to condense are specified by different composition vectors. Using a liquid composition in a dew-point expression, or treating overall composition as though it were automatically a phase composition, gives an incorrect equilibrium state.\n\nIdeal-solution assumptions have a molecular interpretation. Random mixing contributes an entropy of mixing, while the enthalpy and volume changes of mixing are taken as zero. The resulting liquid chemical potential is\n\n\\[\\mu_i^L=\\mu_i^{L,*}+RT\\ln x_i,\\]\n\nwhere the asterisk denotes the pure-liquid reference state at the same temperature and pressure. The logarithmic term lowers the chemical potential relative to pure liquid, reducing the component’s escaping tendency. This formulation also explains why a nonvolatile dissolved substance lowers a solvent’s equilibrium vapor pressure.\n\nFor a dilute solute, the appropriate limiting relation is often Henry’s law, associated with William Henry’s work in 1803. One common convention is\n\n\\[p_i=H_i x_i\\]\n\nat sufficiently low solute concentration and low gas pressure. Unlike Raoult’s law, which is approached by a solvent near its pure state, Henry’s law describes the infinite-dilution limit of a solute. Its constant depends strongly on temperature and on the identities of both solute and solvent. Henry constants are published in several reciprocal and concentration-based conventions, so their numerical values cannot be compared without checking definitions and units.\n\nDissolved oxygen or nitrogen in water illustrates the dilute-gas limit. For gases that react with the solvent, a Henry relation generally applies to the physically dissolved molecular species, not automatically to the total concentration of all chemically transformed forms."
    },
    {
      "heading": "Nonideality, relative volatility, and azeotropes",
      "text": "Real liquids depart from ideal-solution behavior because unlike molecular contacts differ from like contacts. Hydrogen bonding, molecular size differences, polarity, and association can all affect the free energy of mixing. These effects are commonly expressed using an activity coefficient, \\(\\gamma_i\\), defined relative to a specified liquid reference state. When vapor nonideality and liquid-pressure corrections are negligible, the resulting modified Raoult relation is\n\n\\[y_iP=x_i\\gamma_iP_i^{\\mathrm{sat}}.\\]\n\nA value \\(\\gamma_i>1\\) indicates a greater escaping tendency than predicted by the ideal-liquid reference; \\(\\gamma_i<1\\) indicates a smaller one.\n\nPositive deviations from Raoult’s law can produce a maximum in total pressure at fixed temperature and a corresponding minimum in boiling temperature at fixed pressure. Negative deviations can produce the reverse. Molecular explanations must account for all interactions disrupted and formed during mixing: the mere presence of hydrogen bonding does not establish the sign of the deviation. Mixing may break strong interactions already present in the pure components as well as create new ones.\n\nThe separation of components \\(i\\) and \\(j\\) is often characterized by relative volatility,\n\n\\[\\alpha_{ij} = \\frac{y_i/x_i}{y_j/x_j}.\\]\n\nFor an ideal vapor and an activity-coefficient liquid model,\n\n\\[\\alpha_{ij} = \\frac{\\gamma_iP_i^{\\mathrm{sat}}} {\\gamma_jP_j^{\\mathrm{sat}}}.\\]\n\nLarge values indicate substantial vapor enrichment of component \\(i\\) relative to \\(j\\). Values near unity indicate difficult separation by ordinary distillation. Relative volatility is generally composition- and temperature-dependent, even when it is approximated as constant in preliminary calculations.\n\nAn azeotrope is a boiling mixture whose equilibrium vapor and liquid have the same composition. For a homogeneous binary azeotrope, \\(y_i=x_i\\), and both component equilibrium ratios equal unity. At approximately atmospheric pressure, ethanol and water form a minimum-boiling azeotrope near \\(78.2\\,^\\circ\\mathrm{C}\\), containing about 95.6% ethanol by mass, or about 89.5% by mole. Ordinary distillation at that pressure cannot cross this composition to produce pure ethanol from a water-rich feed.\n\nAzeotropes are not compounds with fixed molecular formulas. Their compositions usually change with pressure, and some exist only within a limited pressure range. In systems with limited liquid miscibility, vapor may coexist with two distinct liquid phases, producing heterogeneous azeotropic behavior. These features distinguish azeotropy from the ordinary approach to equal volatility near a critical point and explain why separation methods may require pressure changes, an additional solvent, adsorption, or a membrane rather than simply more distillation stages."
    },
    {
      "heading": "Phase diagrams and the geometry of coexistence",
      "text": "A phase diagram represents the combinations of temperature, pressure, and composition at which phases are stable. For binary VLE, two particularly useful projections are temperature–composition diagrams at fixed pressure and pressure–composition diagrams at fixed temperature. Both distinguish a bubble point, where an initially liquid sample develops an infinitesimal vapor phase, from a dew point, where an initially vapor sample develops an infinitesimal liquid phase.\n\nAt fixed pressure, a conventional binary temperature–composition diagram has separate bubble and dew curves enclosing a two-phase region. A horizontal tie line at a selected temperature connects the equilibrium liquid composition \\(x_i\\) to the equilibrium vapor composition \\(y_i\\). The overall composition \\(z_i\\) lies between those endpoints, but it is generally equal to neither. The phase amounts follow the lever rule. If \\(\\beta\\) is the vapor fraction on a molar basis,\n\n\\[z_i=(1-\\beta)x_i+\\beta y_i,\\]\n\nand, for a suitable component,\n\n\\[\\beta=\\frac{z_i-x_i}{y_i-x_i}.\\]\n\nThe same geometry applies to pressure–composition diagrams at fixed temperature, although the ordering of the phase regions changes. At sufficiently high pressure, a typical subcritical mixture is liquid; lowering pressure reaches the bubble boundary, then a two-phase region, and finally the dew boundary. Azeotropes appear where the bubble and dew curves meet at an interior composition. Pure-component endpoints are additional meeting points when both pure substances possess liquid–vapor coexistence at the specified conditions.\n\nMulticomponent mixtures require a broader representation. At fixed overall composition, a pressure–temperature phase envelope contains bubble and dew boundaries that meet at the mixture critical point. The highest temperature on the envelope is called the cricondentherm, and the highest pressure is the cricondenbar. Neither is generally identical to the critical temperature or critical pressure of the mixture. This distinction is important in reservoir fluids and natural-gas processing, where phase appearance cannot reliably be inferred from a single “boiling point.”\n\nSome gas-condensate mixtures exhibit retrograde condensation: lowering pressure at fixed temperature can first produce liquid from an initially single gas-like phase and, upon further pressure reduction, reduce the liquid fraction again. Mixtures can also exhibit liquid–liquid equilibrium, yielding two liquids and sometimes an additional vapor. In such cases, a two-phase VLE diagram is only a partial representation of the stable phase behavior. Complete analysis must identify all stable phases rather than forcing every state into one liquid and one vapor."
    },
    {
      "heading": "Thermodynamic models and their historical development",
      "text": "Modern VLE modeling grew from experimental vapor-pressure laws into a framework based on chemical potentials and free energy. J. Willard Gibbs’s work on heterogeneous equilibrium in 1876–1878 supplied the general thermodynamic foundation. Later developments separated into two broad approaches: models that describe liquid nonideality through excess Gibbs energy, and equations of state that describe both liquid and vapor using a common pressure–volume–temperature formulation.\n\nIn the activity-coefficient approach, an excess molar Gibbs energy \\(g^E\\) measures departure from an ideal liquid solution. Activity coefficients are obtained by differentiation:\n\n\\[RT\\ln\\gamma_i = \\left( \\frac{\\partial ng^E}{\\partial n_i} \\right)_{T,P,n_{j\\ne i}}.\\]\n\nBecause all coefficients derive from the same free-energy expression, they are linked by the Gibbs–Duhem equation. At fixed temperature and pressure,\n\n\\[\\sum_i x_i\\,d\\ln\\gamma_i=0.\\]\n\nThus, component activity coefficients cannot be assigned independently without risking thermodynamic inconsistency.\n\nMargules and van Laar expressions provide relatively simple descriptions of binary mixtures. The Wilson model, introduced in 1964, uses a local-composition concept but does not represent liquid–liquid splitting. NRTL, introduced by Henri Renon and John Prausnitz in 1968, and UNIQUAC, introduced by Denis Abrams and Prausnitz in 1975, can represent strongly nonideal systems and liquid immiscibility when appropriately parameterized. UNIFAC, also introduced in 1975, estimates liquid nonideality from molecular functional groups, enabling predictions when direct mixture data are unavailable. Such predictions remain dependent on the coverage and quality of group-interaction parameters.\n\nFor high-pressure mixtures, cubic equations of state are widely used. The Soave modification of the Redlich–Kwong equation appeared in 1972, followed by the Peng–Robinson equation of state in 1976. These models use critical properties, molecular acentric factors, and mixing rules to calculate fugacity coefficients in both phases. Binary interaction parameters commonly improve mixture predictions, but their fitted values may not extrapolate reliably across temperature, composition, or chemically different systems.\n\nA general activity-coefficient–fugacity formulation is\n\n\\[y_i\\phi_i^VP = x_i\\gamma_i\\phi_i^{\\mathrm{sat}}P_i^{\\mathrm{sat}} \\exp\\left[ \\int_{P_i^{\\mathrm{sat}}}^{P} \\frac{v_i^L}{RT}\\,dP \\right].\\]\n\nThe exponential is the Poynting correction for liquid pressure. At low pressure, both it and the vapor fugacity coefficients often approach unity. Near critical conditions, or when a component has no pure-liquid saturation state at the system temperature, an equation-of-state treatment or another suitable reference-state formulation is needed. Model choice therefore depends on the physical regime rather than on algebraic convenience alone."
    },
    {
      "heading": "Flash calculations and numerical phase-equilibrium problems",
      "text": "A basic engineering calculation asks how a feed divides into equilibrium vapor and liquid at specified temperature and pressure. This is an isothermal flash calculation, named for flash evaporation, in which part of a liquid vaporizes after a pressure reduction. Let the feed mole fractions be \\(z_i\\), the vapor fraction be \\(\\beta\\), and the equilibrium ratios be\n\n\\[K_i=\\frac{y_i}{x_i}.\\]\n\nCombining these definitions with component material balances gives\n\n\\[x_i=\\frac{z_i}{1+\\beta(K_i-1)}, \\qquad y_i=K_ix_i.\\]\n\nRequiring both phase compositions to sum to unity leads to the Rachford–Rice equation, published in 1952:\n\n\\[\\sum_i \\frac{z_i(K_i-1)} {1+\\beta(K_i-1)} =0.\\]\n\nFor positive, fixed \\(K_i\\), the function is nonincreasing over the physically admissible interval. A root with \\(0<\\beta<1\\) gives a two-phase split. Boundary evaluations help determine whether the assumed equilibrium ratios imply a liquid-only state, a vapor-only state, or a two-phase state. This scalar calculation is efficient because it separates phase-fraction determination from much of the thermodynamic property evaluation.\n\nIn real mixtures, the \\(K_i\\) values are not generally known in advance. They depend on temperature, pressure, and the unknown phase compositions. A typical algorithm begins with estimated \\(K_i\\), solves for \\(\\beta\\), computes \\(\\mathbf{x}\\) and \\(\\mathbf{y}\\), evaluates phase fugacities, and updates the equilibrium ratios until the component fugacities agree. Successive substitution is simple but can converge slowly; Newton-type methods use derivatives to improve convergence. Near a critical point, where liquid and vapor compositions become similar, numerical conditioning becomes particularly difficult.\n\nBubble-point and dew-point calculations are limiting flash problems. For a known liquid composition, a bubble calculation finds the temperature or pressure at which\n\n\\[\\sum_i x_iK_i=1.\\]\n\nFor a known vapor composition, a dew calculation satisfies\n\n\\[\\sum_i\\frac{y_i}{K_i}=1.\\]\n\nThese relations may themselves require iteration because each \\(K_i\\) depends on the sought temperature or pressure and on the incipient phase composition. A robust calculation also tests phase stability rather than assuming that a converged two-phase solution is the stable one.\n\nPractical equipment often requires an energy balance in addition to phase equilibrium. An adiabatic flash specifies feed enthalpy and outlet pressure rather than outlet temperature. The unknown temperature and phase fraction must then satisfy both component balances and an enthalpy balance. Vaporization consumes latent heat, so pressure reduction commonly cools the remaining material. Equilibrium alone determines possible phase compositions; the conservation of mass and first law of thermodynamics determine how much of each phase forms under the imposed process constraints."
    },
    {
      "heading": "Experimental determination and data quality",
      "text": "VLE measurements establish the temperature, pressure, and phase compositions of a system after it reaches equilibrium. Static methods seal a known mixture in a cell and measure its equilibrium state without continuous bulk circulation. Circulation methods repeatedly move vapor, liquid, or both through an apparatus to promote contact and provide representative samples. Boiling-point instruments, including recirculating ebulliometers, are especially useful for low-pressure temperature–composition measurements. High-pressure work commonly uses pressure-resistant equilibrium cells, sometimes with windows that permit direct observation of phase appearance.\n\nReliable sampling is essential because a sample can change composition as soon as its pressure or temperature changes. Vapor may partially condense in a transfer line, while withdrawn liquid may flash. Either process fractionates the sample before analysis. Heated sampling lines, small sample volumes, and carefully controlled sampling procedures reduce these effects. Phase compositions are frequently determined by gas chromatography; other methods include spectroscopy, refractive-index measurements, and density-based analysis when the mixture is sufficiently well characterized.\n\nTemperature and pressure errors propagate nonlinearly into calculated equilibrium properties. Saturation pressure often varies steeply with temperature, making a small thermometer offset significant. Calibration, fluid purity, cell temperature uniformity, and elimination of leaks or noncondensable gases are therefore central to data quality. At low pressures, a small quantity of residual air can measurably alter total pressure. For water-containing or hygroscopic mixtures, unnoticed moisture can turn a nominally binary experiment into a ternary one.\n\nThermodynamic consistency tests use relations among measured properties rather than merely checking whether data points form a smooth curve. The Gibbs–Duhem equation constrains composition-dependent activity coefficients, and suitable integral or differential tests can reveal incompatible vapor and liquid compositions. However, tests must respect the experimental path: isothermal and isobaric datasets require different treatment because temperature-dependent excess enthalpy terms can enter. Passing a consistency test is not proof of accuracy; systematic errors or compensating errors may remain.\n\nAn experimental report is most useful when it includes measurement uncertainty, sample preparation, purity, analytical calibration, operating ranges, and the method used to establish equilibrium. Near the critical point, long relaxation times, weak density contrast, and small composition differences complicate both observation and sampling. At very low concentrations, analytical detection limits may dominate the uncertainty in a partition ratio. Data fitted over one interval should not automatically be extrapolated into dilute limits, liquid-immiscibility regions, or critical conditions without additional physical constraints."
    },
    {
      "heading": "Industrial and environmental applications",
      "text": "Distillation exploits the difference between equilibrium liquid and vapor compositions through repeated contacting. A theoretical equilibrium stage produces exiting phases that satisfy VLE at the stage temperature and pressure. Real trays and packed columns depart from this ideal because interphase mass transfer and heat transfer require finite driving forces. Stage efficiencies or rate-based models connect equilibrium predictions to actual equipment. Reflux and reboiling create opposing liquid and vapor flows, allowing successive enrichment beyond what a single equilibrium flash can achieve.\n\nAzeotropes impose important limits on conventional distillation. Ethanol dehydration, for example, requires a method beyond simple atmospheric rectification when purity above the ethanol–water azeotrope is needed. Industrial approaches include water-selective adsorption and processes that alter mixture equilibrium using an additional component. Pressure-swing distillation can separate some azeotropic mixtures when their azeotropic compositions shift sufficiently with pressure. The relevant feasibility question is not merely whether an azeotrope exists, but how the complete phase behavior changes under the proposed operating conditions.\n\nRefrigeration and heat-pump cycles rely on controlled condensation and evaporation. Pure refrigerants change phase at a single saturation temperature at fixed pressure, whereas many refrigerant blends have different bubble and dew temperatures. This temperature glide affects heat-exchanger temperature profiles, charging behavior, and interpretation of operating measurements. In petroleum and natural-gas systems, VLE calculations determine separator yields, hydrocarbon dew points, and the formation of condensate during pressure changes. High-pressure behavior often requires an equation of state rather than a low-pressure activity-coefficient model.\n\nEnvironmental partitioning also involves VLE, particularly the transfer of volatile substances between water and air. Henry-type relations help describe the equilibrium distribution of dilute organic compounds and dissolved gases. Actual exchange rates additionally depend on diffusion, turbulence, and interfacial transport. For carbon dioxide in water, physical dissolution is coupled to acid–base reactions; the total dissolved inorganic carbon cannot be inferred from a molecular carbon-dioxide partition coefficient alone. Likewise, humidity over saline water differs from that over pure water because dissolved salts lower water activity.\n\nThe distinction between equilibrium and transport is crucial across these applications. A wet surface exposed to moving, unsaturated air may have an interface close to local equilibrium while the surrounding gas remains far from saturation. Conversely, rapid depressurization can temporarily produce supersaturated or metastable states because bubble nucleation is delayed. In small pores and droplets, curvature, adsorption, and confinement can shift coexistence away from bulk-fluid predictions. Engineering and environmental models therefore use VLE as an interfacial or limiting thermodynamic condition while separately representing transport, reaction, and phase-formation kinetics."
    }
  ],
  "links": [
    "thermodynamics",
    "distillation",
    "thermodynamic-equilibrium",
    "temperature",
    "pressure",
    "chemical-potential",
    "surface-tension",
    "gibbs-free-energy",
    "fugacity",
    "gas-constant",
    "vapor-pressure",
    "critical-point",
    "clapeyron-equation",
    "enthalpy",
    "latent-heat",
    "ideal-gas",
    "water",
    "evaporation",
    "raoults-law",
    "henrys-law",
    "oxygen",
    "nitrogen",
    "hydrogen-bond",
    "activity-coefficient",
    "azeotrope",
    "ethanol",
    "phase-diagram",
    "dew-point",
    "equation-of-state",
    "gibbs-duhem-equation",
    "conservation-of-mass",
    "first-law-of-thermodynamics",
    "chromatography",
    "spectroscopy",
    "calibration",
    "measurement-uncertainty",
    "heat",
    "condensation",
    "diffusion",
    "carbon-dioxide"
  ],
  "sources": [],
  "license": "https://creativecommons.org/licenses/by/4.0/"
}