{
  "id": "transconductance",
  "title": "Transconductance",
  "lang": "en",
  "source_lang": "en",
  "summary": "Transconductance measures how much an electronic device’s output current changes in response to a change in its input voltage, usually at a specified operating point.",
  "category": "technology",
  "subcategory": "engineering",
  "type": "concept",
  "aliases": [
    "Mutual conductance",
    "transfer conductance"
  ],
  "generated_at": "2026-11-06",
  "model": "pro/gpt-6.1-sol",
  "url": "https://aiwiki.page/en/transconductance/",
  "translations": {
    "zh-Hans": {
      "url": "https://aiwiki.page/zh/transconductance/",
      "json": "https://aiwiki.page/zh/transconductance.json"
    }
  },
  "sections": [
    {
      "heading": "",
      "text": "Transconductance is the change in an electronic device’s output current per unit change in its input voltage. Usually denoted \\(g_m\\), it is a central parameter in the analysis of electronic amplifiers, especially those built with transistors or vacuum tubes. It describes how effectively a voltage variation controls a current variation, rather than directly specifying voltage gain. Transconductance depends on the device, its operating point, and, in general, signal frequency."
    },
    {
      "heading": "Definition and units",
      "text": "For an output current \\(I_{\\mathrm{out}}\\) controlled by an input voltage \\(V_{\\mathrm{in}}\\), small-signal transconductance is defined as\n\n\\[g_m= \\left. \\frac{\\partial I_{\\mathrm{out}}}{\\partial V_{\\mathrm{in}}} \\right|_Q,\\]\n\nwhere \\(Q\\) denotes the operating point and the other independent terminal voltages are held constant. It is therefore a local derivative of a device’s current–voltage characteristic.\n\nFor a sufficiently small input perturbation,\n\n\\[\\Delta i_{\\mathrm{out}}\\approx g_m\\,\\Delta v_{\\mathrm{in}}.\\]\n\nThe SI unit is the siemens, symbol \\(\\mathrm{S}\\), equivalent to an ampere per volt. Millisiemens and microsiemens are common practical units. Older literature often uses the unit mho, which is equivalent to the siemens.\n\nFor example, a device with \\(g_m=5\\,\\mathrm{mS}\\) produces an output-current change of approximately \\(50\\,\\mu\\mathrm{A}\\) for a \\(10\\,\\mathrm{mV}\\) input-voltage change, provided the signal remains within its approximately linear range.\n\nDistinction from related quantities\n\nTransconductance has the same dimensions as electrical conductance, but describes a different relationship:\n\n- Conductance relates current and voltage at the same port.\n- Transconductance relates output current to input voltage, generally at different ports.\n- Voltage gain relates output voltage to input voltage and is dimensionless.\n- Current gain relates output current to input current and is dimensionless.\n- Transimpedance relates output voltage to input current and is measured in ohms.\n\nAlthough transconductance and transimpedance have reciprocal units, the transimpedance of a circuit is not generally the reciprocal of its transconductance."
    },
    {
      "heading": "Small-signal circuit models",
      "text": "A transistor is nonlinear, but its behavior near a fixed bias point can be approximated by a linear circuit. In such a model, transconductance is represented by a voltage-controlled current source.\n\nFor a field-effect transistor, a simplified low-frequency drain-current relation is\n\n\\[i_d=g_m v_{gs}+g_{ds}v_{ds},\\]\n\nwhere lowercase variables represent small-signal changes. Here \\(v_{gs}\\) is the gate-to-source voltage, \\(v_{ds}\\) is the drain-to-source voltage, and \\(g_{ds}\\) is the output conductance. A more complete model can include body-voltage dependence and terminal capacitances.\n\nThe corresponding output resistance is\n\n\\[r_o=\\frac{1}{g_{ds}}.\\]\n\nIf the output current flows through a load resistance \\(R_L\\), a simplified inverting voltage amplifier has gain\n\n\\[A_v\\approx -g_m(R_L\\parallel r_o),\\]\n\nassuming the source or emitter is held at signal ground and other effects are negligible. The minus sign indicates inversion: an increasing input voltage produces greater device current and a lower output voltage.\n\nThus, high transconductance can increase voltage gain, but gain also depends on loading, output resistance, and circuit configuration. The product \\(g_m r_o\\) is commonly called the device’s intrinsic gain."
    },
    {
      "heading": "Transconductance in major device types",
      "text": "Bipolar junction transistors\n\nFor a bipolar junction transistor in forward-active operation, the ideal collector-current relation is approximately\n\n\\[I_C=I_S e^{V_{BE}/V_T},\\]\n\nwhere \\(I_S\\) is a scale current and\n\n\\[V_T=\\frac{kT}{q}\\]\n\nis the thermal voltage. Here \\(k\\) is the Boltzmann constant, \\(T\\) is absolute temperature, and \\(q\\) is the magnitude of the elementary charge.\n\nDifferentiation gives\n\n\\[g_m=\\frac{I_C}{V_T}.\\]\n\nAt about \\(300\\,\\mathrm{K}\\), \\(V_T\\) is approximately \\(25.9\\,\\mathrm{mV}\\). A collector current of \\(1\\,\\mathrm{mA}\\) therefore corresponds to a transconductance of approximately \\(38.6\\,\\mathrm{mS}\\).\n\nIn this ideal model, transconductance is proportional to collector current. It is distinct from the transistor’s common-emitter current gain, \\(\\beta\\). In the hybrid-\\(\\pi\\) small-signal model, the base input resistance satisfies\n\n\\[r_\\pi=\\frac{\\beta}{g_m}.\\]\n\nAt a fixed collector current, the ideal transconductance decreases as temperature rises. If the bias circuit does not hold collector current constant, however, temperature-induced changes in current also affect \\(g_m\\).\n\nMOS field-effect transistors\n\nFor a metal–oxide–semiconductor field-effect transistor operating in strong inversion and saturation, the ideal long-channel square-law model gives\n\n\\[I_D=\\frac{1}{2}\\mu C_{\\mathrm{ox}}\\frac{W}{L} (V_{GS}-V_{\\mathrm{th}})^2,\\]\n\nneglecting channel-length modulation. Here \\(\\mu\\) is carrier mobility, \\(C_{\\mathrm{ox}}\\) is gate-oxide capacitance per unit area, \\(W/L\\) is the channel width-to-length ratio, and \\(V_{\\mathrm{th}}\\) is threshold voltage.\n\nDefining the overdrive voltage as \\(V_{\\mathrm{ov}}=V_{GS}-V_{\\mathrm{th}}\\),\n\n\\[g_m=\\mu C_{\\mathrm{ox}}\\frac{W}{L}V_{\\mathrm{ov}} =\\frac{2I_D}{V_{\\mathrm{ov}}}.\\]\n\nThese expressions show how bias current, geometry, and overdrive affect transconductance within this model. They are not universally accurate for modern short-channel devices, in which velocity saturation, mobility degradation, and other effects alter the current–voltage relationship.\n\nIn weak inversion, an approximate expression is\n\n\\[g_m\\approx\\frac{I_D}{nV_T},\\]\n\nwhere \\(n\\) is the subthreshold slope factor. This gives a relatively high transconductance per unit drain current, although speed, device area, and signal-handling requirements impose additional trade-offs.\n\nThe ratio \\(g_m/I_D\\), often called transconductance efficiency, is widely used in analog integrated-circuit design to compare operating conditions and balance power consumption against other performance requirements.\n\nJunction field-effect transistors\n\nFor a junction field-effect transistor, an idealized transfer characteristic in saturation is\n\n\\[I_D=I_{DSS} \\left(1-\\frac{V_{GS}}{V_P}\\right)^2.\\]\n\nFor an n-channel device, \\(V_P\\) is the negative gate-to-source cutoff voltage. Within the model’s applicable range,\n\n\\[g_m=g_{m0} \\left(1-\\frac{V_{GS}}{V_P}\\right), \\qquad g_{m0}=\\frac{2I_{DSS}}{|V_P|}.\\]\n\nTransconductance therefore falls as the gate bias moves toward cutoff.\n\nVacuum tubes\n\nIn a vacuum tube, transconductance expresses how plate current changes with control-grid voltage while plate voltage remains fixed:\n\n\\[g_m= \\left. \\frac{\\partial I_a}{\\partial V_g} \\right|_{V_a}.\\]\n\nThe term mutual conductance is particularly associated with tube terminology. For a triode, the differential amplification factor \\(\\mu\\), plate resistance \\(r_p\\), and transconductance satisfy\n\n\\[\\mu=g_m r_p.\\]\n\nTransconductance was an important tube specification before semiconductor amplifiers became dominant and remains relevant to tube-circuit analysis and testing."
    },
    {
      "heading": "Circuit-level transconductance and applications",
      "text": "Transconductance can describe an entire circuit rather than a single device. An operational transconductance amplifier ideally produces\n\n\\[i_{\\mathrm{out}}=g_m(v_+-v_-).\\]\n\nUnlike an ideal voltage-output operational amplifier, it provides an output current proportional to differential input voltage. Its effective transconductance may be adjustable through a bias current.\n\nApplications include:\n\n- Voltage amplification: transistor stages convert an input voltage into a current that develops an output voltage across a load.\n- Tunable filters: transconductance–capacitor circuits combine transconductors with capacitors. Their characteristic frequencies scale with ratios such as \\(g_m/C\\), enabling electronic tuning.\n- Oscillators and variable-gain circuits: adjustable transconductance controls gain or supplies the energy needed to sustain oscillation.\n- Sensor interfaces: transconductance stages help process small signals from sensors, although performance also depends on noise, input impedance, and linearity.\n\nA resistor in a transistor’s source or emitter path introduces local negative feedback. Under simplified conditions, the resulting effective transconductance is approximately\n\n\\[G_m\\approx\\frac{g_m}{1+g_mR}.\\]\n\nWhen \\(g_mR\\gg1\\), \\(G_m\\) approaches \\(1/R\\). This reduces gain but makes the circuit less sensitive to variations in the transistor’s intrinsic transconductance and can improve linearity."
    },
    {
      "heading": "Frequency dependence and practical limits",
      "text": "The familiar real-valued \\(g_m\\) is chiefly a low-frequency, small-signal parameter. At higher frequencies, internal capacitances, carrier transit times, and parasitic elements introduce amplitude changes and phase shifts. More generally, a frequency-dependent short-circuit transfer admittance can be defined as\n\n\\[Y_{21}(\\omega)= \\left. \\frac{I_2(\\omega)}{V_1(\\omega)} \\right|_{V_2=0}.\\]\n\nAt sufficiently low frequencies and under appropriate terminal conditions, this may approach the device’s transconductance. At higher frequencies, capacitive feedthrough can contribute substantially.\n\nA common approximate relationship for a MOS transistor’s unity-current-gain frequency is\n\n\\[f_T\\approx\\frac{g_m}{2\\pi(C_{gs}+C_{gd})},\\]\n\nunder simplifying assumptions. This illustrates why increasing transconductance alone does not guarantee higher speed: capacitance matters as well.\n\nTransconductance also varies with bias, temperature, manufacturing variation, and signal amplitude. Increasing it may require more current or greater device width, with consequences for power dissipation and capacitance. Noise and signal-to-noise ratio depend on additional mechanisms, so a higher \\(g_m\\) is not by itself a complete measure of amplifier quality."
    },
    {
      "heading": "Measurement and specification",
      "text": "Transconductance can be determined by measuring an output-current versus input-voltage curve and calculating its local slope. A small-signal alternative applies a known AC input voltage and measures the resulting output current while maintaining the specified output-terminal voltage.\n\nA meaningful specification identifies the bias point, terminal connections, temperature, signal amplitude, and measurement frequency. A finite voltage step gives an average slope over an interval rather than an exact local derivative. Excessive test amplitude, self-heating, contact resistance, and parasitic capacitance can all influence the measured value."
    }
  ],
  "links": [
    "electronic-amplifier",
    "derivative",
    "international-system-of-units",
    "transistor",
    "bipolar-junction-transistor",
    "boltzmann-constant",
    "temperature",
    "electric-charge",
    "mosfet",
    "capacitor",
    "sensor",
    "resistor",
    "negative-feedback",
    "signal-to-noise-ratio"
  ],
  "sources": [],
  "license": "https://creativecommons.org/licenses/by/4.0/"
}