{
  "id": "stopping-potential",
  "title": "Stopping Potential",
  "lang": "en",
  "source_lang": "en",
  "summary": "Stopping potential is the retarding voltage required to prevent even the most energetic photoelectrons from reaching a collector, revealing their maximum kinetic energy.",
  "category": "science",
  "subcategory": "physics",
  "type": "concept",
  "aliases": [
    "Stopping voltage",
    "Cutoff potential",
    "Cutoff voltage"
  ],
  "generated_at": "2026-11-06",
  "model": "pro/gpt-6.1-sol",
  "url": "https://aiwiki.page/en/stopping-potential/",
  "translations": {
    "zh-Hans": {
      "url": "https://aiwiki.page/zh/stopping-potential/",
      "json": "https://aiwiki.page/zh/stopping-potential.json"
    }
  },
  "sections": [
    {
      "heading": "",
      "text": "Stopping potential is the magnitude of the retarding potential difference required to prevent even the most energetic emitted electrons from reaching a collecting electrode in a photoelectric-effect experiment. It converts a measurement of voltage into a measurement of maximum electron kinetic energy. For electrons emitted by monochromatic light under ideal single-photon conditions, the stopping potential \\(V_s\\) satisfies \\(eV_s=h\\nu-\\phi\\), where \\(e\\) is the elementary charge, \\(h\\) is Planck’s constant, \\(\\nu\\) is the light frequency, and \\(\\phi\\) is the emitting surface’s work function."
    },
    {
      "heading": "Physical principle and sign convention",
      "text": "A typical experiment uses an illuminated emitting electrode and a collector inside an evacuated enclosure. Incident light releases electrons from the emitting surface. When the collector is sufficiently positive relative to the emitter, it attracts the electrons, producing a measurable photocurrent. Making the collector negative relative to the emitter creates a retarding electric field.\n\nAn electron has charge \\(-e\\), where \\(e\\) is the positive elementary charge. As it moves toward a collector at lower electric potential, its electrical potential energy increases and its kinetic energy decreases. If the retarding potential difference has magnitude \\(V\\), the corresponding increase in potential energy is \\(eV\\).\n\nIn the ideal stopping condition,\n\n\\[K_{\\max}=eV_s,\\]\n\nwhere \\(K_{\\max}\\) is the maximum kinetic energy of the emitted electrons. Electrons with less energy are rejected at smaller retarding voltages; at the stopping potential, even the highest-energy electrons cannot produce a collected photocurrent.\n\nThe stopping potential is normally quoted as a positive magnitude. If the signed electrode voltage is instead defined as\n\n\\[\\Delta V=V_{\\text{collector}}-V_{\\text{emitter}},\\]\n\nthen the stopping condition occurs at \\(\\Delta V=-V_s\\). Explicitly stating this convention avoids an apparent sign disagreement between otherwise equivalent formulas.\n\nStopping potential is measured in volts, not units of energy. Multiplying it by \\(e\\) gives an energy in joules. Expressed in electronvolts, the maximum kinetic energy has the same numerical value as the stopping potential expressed in volts."
    },
    {
      "heading": "Relation to the photoelectric equation",
      "text": "In Einstein’s description of photoemission, one photon transfers energy \\(h\\nu\\) to an electron. The work function \\(\\phi\\) is the minimum energy required to remove an electron from the material into vacuum. Electrons that escape with the greatest available kinetic energy satisfy\n\n\\[K_{\\max}=h\\nu-\\phi.\\]\n\nCombining this relation with the stopping condition gives\n\n\\[V_s=\\frac{h}{e}\\nu-\\frac{\\phi}{e}.\\]\n\nThus, for a fixed emitting surface, the ideal stopping potential varies linearly with light frequency. The slope is \\(h/e\\), linking the measured voltage to the Planck constant.\n\nThe threshold frequency is\n\n\\[\\nu_0=\\frac{\\phi}{h}.\\]\n\nBelow this frequency, ordinary single-photon photoemission cannot occur, regardless of how many below-threshold photons arrive, provided multiphoton processes and other emission mechanisms are negligible. Above threshold,\n\n\\[V_s=\\frac{h}{e}(\\nu-\\nu_0).\\]\n\nUsing the vacuum wavelength \\(\\lambda\\) and the speed of light \\(c\\), the same relationship becomes\n\n\\[V_s=\\frac{hc}{e\\lambda}-\\frac{\\phi}{e}.\\]\n\nFrequency and intensity\n\nFrequency determines the energy supplied by each photon. Increasing frequency therefore increases the maximum electron energy and, consequently, the stopping potential.\n\nAt fixed frequency, increasing light intensity primarily increases the number of emitted electrons and hence the photocurrent. In the ideal single-photon regime, it does not increase the stopping potential. This distinction helped establish the quantum description of light: energy is transferred in discrete photon interactions rather than being accumulated continuously from a classical light wave.\n\nAt high intensities, multiphoton emission, heating, and interactions among emitted electrons can invalidate this simple separation."
    },
    {
      "heading": "Experimental determination",
      "text": "The stopping potential is obtained from a photocurrent–voltage curve. A typical measurement involves:\n\n- Illuminating a stable surface with light of known frequency and sufficiently narrow spectral bandwidth.\n- Measuring the collected current over a range of electrode voltages.\n- Increasing the retarding voltage until the photoemission contribution approaches zero.\n- Determining the cutoff using a specified background subtraction, fitting method, or current threshold.\n\nThe current usually decreases gradually rather than dropping abruptly because emitted electrons have a distribution of energies and directions. The stopping potential characterizes the upper-energy edge of the collected distribution, not its mean energy.\n\nCollector geometry also matters. In an ideal planar retarding field, the barrier tests the component of kinetic energy associated with motion perpendicular to the electrodes. The textbook identification of the cutoff with total maximum kinetic energy assumes that the collection geometry admits electrons whose motion samples that maximum appropriately.\n\nImportant experimental limitations\n\nSeveral effects complicate the interpretation of a measured cutoff:\n\n- Contact potentials: Differences between electrode work functions produce an internal potential difference. The externally applied stopping voltage may therefore require an offset correction before it can be identified with \\(K_{\\max}/e\\).\n- Surface condition: Adsorption, oxidation, contamination, and differences between crystal faces can alter the effective work function or create spatially varying emission thresholds.\n- Spectral bandwidth: Higher-frequency components of the illumination can determine the observed cutoff even when they represent only a small fraction of the incident light.\n- Background currents: Leakage, dark current, and photoemission from the collector can obscure the point at which the emitter’s photocurrent vanishes.\n- Space charge: Interactions among emitted electrons can modify the local field and distort the current–voltage curve.\n- Instrumental resolution: Voltage accuracy, current sensitivity, and the chosen cutoff procedure contribute to measurement uncertainty.\n\nConsequently, an uncorrected voltage intercept does not necessarily give the emitting surface’s work function directly. A constant contact-potential offset can shift the intercept while leaving the frequency-dependent slope unchanged."
    },
    {
      "heading": "Historical significance and applications",
      "text": "Albert Einstein introduced the photon-based photoelectric relation in 1905. Robert Millikan’s experiments, reported in 1916, quantitatively confirmed the predicted relationship between stopping potential and light frequency and yielded a determination of Planck’s constant. Such measurements became important evidence in the development of quantum mechanics.\n\nStopping-potential experiments remain common in physics education because they connect electrical measurements with photon energy and distinguish the effects of light frequency from those of intensity. Historically, they also provided a method for determining \\(h/e\\). In the modern International System of Units, both \\(h\\) and \\(e\\) have exact defined values, so such experiments test apparatus and physical models rather than determine previously unknown defining constants.\n\nThe underlying principle extends beyond photoemission. Retarding-potential analyzers use an adjustable electrostatic barrier to investigate charged-particle energy distributions, including those in plasmas. For particles with charge magnitude \\(|q|\\), a suitable retarding barrier of magnitude \\(V\\) corresponds to an energy threshold \\(|q|V\\). The analyzer geometry and particle trajectories determine which component of the energy is selected.\n\nStopping potential should not be confused with stopping power, which describes the energy a moving particle loses per unit distance while passing through matter, rather than the voltage required to reject it."
    }
  ],
  "links": [
    "electron",
    "photoelectric-effect",
    "kinetic-energy",
    "electrode",
    "electric-current",
    "electric-field",
    "elementary-charge",
    "electric-potential",
    "potential-energy",
    "electronvolt",
    "photon",
    "work-function",
    "planck-constant",
    "speed-of-light",
    "measurement-uncertainty",
    "albert-einstein",
    "quantum-mechanics",
    "international-system-of-units",
    "plasma"
  ],
  "sources": [],
  "license": "https://creativecommons.org/licenses/by/4.0/"
}