{
  "id": "spin-coating",
  "title": "Spin Coating",
  "lang": "en",
  "source_lang": "en",
  "summary": "Spin coating is a thin-film deposition technique in which rotation spreads a liquid across a substrate while excess liquid is expelled and solvent evaporates.",
  "category": "technology",
  "subcategory": "engineering",
  "type": "concept",
  "aliases": [
    "Spin-coating",
    "centrifugal coating"
  ],
  "generated_at": "2026-11-05",
  "model": "pro/gpt-6.1-sol",
  "url": "https://aiwiki.page/en/spin-coating/",
  "translations": {
    "zh-Hans": {
      "url": "https://aiwiki.page/zh/spin-coating/",
      "json": "https://aiwiki.page/zh/spin-coating.json"
    }
  },
  "sections": [
    {
      "heading": "",
      "text": "Spin coating is a method of depositing a thin film by applying a liquid formulation to a substrate and rotating it at high speed. Rotation drives the liquid outward, expelling excess material and leaving a progressively thinner layer; solvent evaporation usually helps determine the final thickness and solidifies the coating. The method is widely used to apply photoresists in semiconductor manufacturing and to prepare polymer, optical, and functional-material films. It is particularly suited to flat substrates where reproducible thickness and a smooth surface are required."
    },
    {
      "heading": "Operating principle",
      "text": "A spin coater typically consists of a motor-driven chuck, a substrate-holding mechanism, a liquid dispenser, and an enclosure that collects expelled liquid and controls exhaust. A vacuum chuck commonly holds wafers or glass plates, although mechanical fixtures are also used.\n\nThe liquid rotates with the substrate because of adhesion and viscous stresses. In the rotating reference frame, centrifugal acceleration promotes outward radial flow. The interaction between this driving force and viscosity governs how rapidly the liquid spreads and thins. Meanwhile, evaporation removes solvent, increases the concentration of dissolved or suspended material, and often raises viscosity substantially.\n\nSeveral overlapping stages are commonly distinguished:\n\n- Dispensing: A measured quantity of liquid is placed on a stationary or rotating substrate.\n- Spreading and acceleration: The substrate accelerates, distributing the liquid over its surface.\n- Flow-driven thinning: Liquid moves toward the perimeter and is expelled.\n- Evaporation and immobilization: Solvent loss reduces fluid mobility until the coating becomes effectively fixed.\n\nThese stages are not sharply separated. Evaporation begins during dispensing, and outward flow may continue while the coating is drying. Some formulations also undergo chemical reactions, gelation, or crystallization during spinning.\n\nSpin coating is a coating operation rather than necessarily a complete film-conversion process. Subsequent heating, curing, exposure, or other treatment may be required to produce the intended properties."
    },
    {
      "heading": "Process sequence and variants",
      "text": "Substrate preparation\n\nParticles, surface residues, and variations in surface chemistry can interrupt liquid spreading or weaken adhesion. Substrates are therefore commonly cleaned and, where appropriate, treated to adjust their wettability.\n\nWetting is often characterized using the contact angle, although a single contact-angle measurement does not fully describe the behavior of a rapidly evaporating, multicomponent coating liquid. Poor wetting can cause the film to retract and expose parts of the substrate.\n\nStatic and dynamic dispensing\n\nIn static dispensing, liquid is deposited before rotation begins. The initial volume must be sufficient to cover the substrate during acceleration.\n\nIn dynamic dispensing, liquid is introduced while the substrate is already rotating, usually at a relatively low speed. This can reduce material consumption or improve initial distribution for some formulations. Its effectiveness depends on dispensing position, flow rate, substrate wettability, and the rate of solvent loss.\n\nA coating program may include a low-speed spreading step followed by a higher-speed thinning step. More complex programs use several speeds, controlled acceleration ramps, or additional liquid additions.\n\nDrying and post-treatment\n\nAfter spinning, the coating may retain solvent even when it appears dry. Photoresist films commonly receive a post-application bake to reduce residual solvent before subsequent lithographic processing. Other materials may require thermal curing, ultraviolet curing, or conversion of a chemical precursor into an inorganic film.\n\nRepeated coating and treatment cycles can build multilayer structures or thicker coatings. However, a new solvent can dissolve, swell, or otherwise alter a previously deposited layer unless the materials and processing sequence are compatible."
    },
    {
      "heading": "Film-thickness control and physical models",
      "text": "Final thickness depends on more than rotational speed. Important variables include:\n\n- Solids concentration and molecular characteristics.\n- Liquid viscosity and its change during drying.\n- Solvent volatility and solvent mixtures.\n- Spin speed, duration, and acceleration.\n- Substrate dimensions, shape, and surface condition.\n- Ambient temperature, humidity, and airflow.\n- Dispensed volume and the timing of dispensing.\n\nFor many formulations within a limited processing range, dry-film thickness can be represented empirically as\n\n\\[h_{\\mathrm{dry}} = K\\omega^{-n},\\]\n\nwhere \\(h_{\\mathrm{dry}}\\) is the final thickness, \\(\\omega\\) is angular speed, and \\(K\\) and \\(n\\) are fitted parameters. An exponent near one-half is common in some evaporation-influenced regimes, but it is not a universal law. A manufacturer’s or laboratory’s thickness–speed curve applies only to the formulation and conditions under which it was established.\n\nIdealized hydrodynamic thinning\n\nA classical model considers a uniform, incompressible Newtonian liquid on a flat rotating disk, neglecting evaporation, edge effects, and changes in viscosity. Under thin-film flow assumptions,\n\n\\[\\frac{dh}{dt} = -\\frac{2\\rho\\omega^2}{3\\eta}h^3,\\]\n\nwhere \\(h\\) is wet-film thickness, \\(\\rho\\) is liquid density, and \\(\\eta\\) is dynamic viscosity. At constant speed, its solution is\n\n\\[h(t) = \\left[ h_0^{-2} + \\frac{4\\rho\\omega^2}{3\\eta}t \\right]^{-1/2},\\]\n\nwhere \\(h_0\\) is the initial thickness.\n\nThis model explains how a thicker region can thin faster than a thinner region, promoting uniformity under ideal conditions. It also predicts faster thinning at higher rotational speed and slower thinning at higher viscosity. It does not, by itself, predict the final thickness of a dried polymer film.\n\nA simplified evaporation-inclusive balance can be written as\n\n\\[\\frac{dh}{dt} = -\\frac{2\\rho\\omega^2}{3\\eta}h^3-E,\\]\n\nwhere \\(E\\) is an effective solvent-loss rate expressed as thickness per unit time. Realistic descriptions must account for concentration-dependent viscosity, solvent transport, and sometimes non-Newtonian flow. The viscoelastic behavior of concentrated polymer solutions can further limit simple models."
    },
    {
      "heading": "Materials and applications",
      "text": "Microelectronics and microfabrication\n\nSpin coating is a standard method for applying photoresist to semiconductor wafers. Coating uniformity affects exposure and development behavior, while edge and backside contamination can interfere with wafer handling.\n\nOther applications include spin-on dielectric materials, planarizing layers, and coatings used in microelectromechanical systems. Although some formulations smooth small surface variations, spin coating does not necessarily provide uniform coverage over deep trenches or steep steps.\n\nPolymers, optical coatings, and functional films\n\nSolutions of polymers can form smooth films for optical studies, surface modification, membranes, and electronic devices. Spin coating is also used with sol–gel precursors, which can be converted into oxide coatings through subsequent chemical and thermal treatment.\n\nDispersions containing nanoparticles or other solid constituents can be spin-coated, provided aggregation, sedimentation, and drying behavior are adequately controlled.\n\nResearch applications include active and interfacial layers in organic photovoltaics and perovskite solar cells. In perovskite processing, antisolvent addition during spinning is one method used to influence supersaturation and crystallization. Film quality depends strongly on the particular composition and processing environment."
    },
    {
      "heading": "Uniformity, defects, and measurement",
      "text": "A nominally uniform coating can exhibit several characteristic defects:\n\nDefect | Typical contributing factors\nEdge bead | Liquid accumulation and altered flow near the substrate perimeter\nRadial streaks | Particles, dispensing irregularities, or nonuniform flow and drying\nPinholes or uncovered regions | Contamination, trapped bubbles, or inadequate wetting\nDewetting | Retraction or breakup of a film that does not remain stable on the surface\nThickness gradients | Uneven airflow, substrate geometry, or nonuniform drying\nCracking | Drying or conversion stresses exceeding the film’s resistance to fracture\n\nEdge-bead removal can use a localized solvent stream to clear the perimeter. Backside rinsing may also be incorporated into automated equipment.\n\nFilm thickness is commonly measured by ellipsometry, optical reflectometry, or step-height profilometry. Measurements across multiple positions are necessary to distinguish average thickness from spatial uniformity. The condition of measurement also matters: an as-spun film and a baked film may have different thicknesses because of solvent removal, densification, or chemical conversion."
    },
    {
      "heading": "Historical development",
      "text": "Spin coating became an important industrial process through its use in photographic and microelectronic coatings. A foundational theoretical treatment was published in 1958 by Alfred G. Emslie, Francis T. Bonner, and Leslie G. Peck, who analyzed the flow of a viscous liquid on a rotating disk. Later work incorporated evaporation, changing solution concentration, and more complex fluid behavior.\n\nAs semiconductor fabrication developed, spin coating was integrated into automated processing tracks combining liquid dispensing, wafer handling, baking, and development. Laboratory spin coaters remain widely used because they can produce useful films from relatively small batches of material with comparatively simple equipment."
    },
    {
      "heading": "Advantages and limitations",
      "text": "Spin coating offers rapid processing, straightforward thickness adjustment, and good uniformity on suitable flat substrates. It is effective for small-scale materials screening and for wafer-based manufacturing supported by established recipes and process control.\n\nIts main limitations are:\n\n- Material loss: Much of the dispensed liquid may be expelled rather than incorporated into the film.\n- Geometric restrictions: Large, irregular, curved, or strongly textured surfaces are more difficult to coat uniformly.\n- Environmental sensitivity: Airflow, humidity, and temperature can change evaporation and film formation.\n- Formulation dependence: A successful recipe does not necessarily transfer to a different solvent, material concentration, or substrate.\n- Scale-up constraints: Results obtained on small samples may not transfer directly to larger areas or continuous production.\n\nAlternatives include dip coating, spray coating, blade coating, and slot-die coating. These methods differ in material utilization, substrate compatibility, and suitability for continuous manufacturing. Vapor-phase techniques such as chemical vapor deposition form films through different mechanisms and are preferable for some materials and coverage requirements.\n\nSolvent vapors, rotating components, and expelled chemicals also impose equipment and process-safety requirements. Enclosures, compatible exhaust systems, secure substrate retention, and appropriate waste collection are therefore integral to spin-coating installations."
    }
  ],
  "links": [
    "photoresist",
    "semiconductor",
    "viscosity",
    "lithography",
    "viscoelasticity",
    "polymer",
    "organic-photovoltaics",
    "perovskite-solar-cell",
    "process-control",
    "process-safety"
  ],
  "sources": [],
  "license": "https://creativecommons.org/licenses/by/4.0/"
}